Yard Machines MTD PS Operator's Manual page 9

For Parts Call 606-678-9623 or 606-561-4983 For Parts Call 606-678-9623 or 606-561-4983
A. GRIP SAW FIRMLY: Hold the chain saw firmly with
both hands when the
good firm grip on the saw with both hands, the right
hand on the rear handle, and the left hand on the
front handle.
B. Do not over reach.
C. Keep proper footing and balance at all times.
D. Do not let the nose of the guide bar contact a log,
branch, ground or other obstruction.
E. Do not cut above shoulder height.
F. Use devices, such as low-kickback chain, guide bar
nose guards, chain brakes and special guide bars,
which reduce the risks associated with kickback.
G. Use only replacement bars and chains specified by
the manufacturer or the equivalent.
H. There are no other replacement components for
achieving kickback protection in accordance with
CSA Z62.3.
20.POWER SUPPLY: Connect the chain saw to correct
voltage; be sure that the voltage supplied is the same
as that specified on the nameplate of the tool.
21.DO NOT operate a chain saw that is damaged,
improperly adjusted, or not completely and securely
assembled. Be sure that the saw chain stops moving
when the trigger is released.
22.DO NOT attempt operations beyond your capacity or
experience.
23.DO NOT operate a chain saw with one hand! Serious
injury to the operator, helpers, or bystanders may
result from one-handed operation. A chain saw is
intended for two-handed use.
24.TO REDUCE potential for electric shock, do not oper-
ate the saw on wet or slippery surfaces, or during
snow storms, rain storms, and other adverse weather
conditions.
25.DO NOT allow dirt, debris or sawdust to build up on
the motor or outside air vents.
26.Follow the manufacturer's sharpening and mainte-
nance instructions for the saw chain.
27.Cut at high motor speeds.
28.Operation of a chain saw should be restricted to
mature, properly instructed individuals.
29.Your chain saw is intended for occasional homeowner
use. It is not made for heavy continuous use.
30.DO NOT FORCE a small saw to do a job requiring a
heavier duty unit.
motor is running. Keep a
www.mymowerparts.com www.mymowerparts.com
31.EXAMINE THE ELECTRICAL SWITCHES. Do not use
the chain saw if the switches do not properly turn on and
off. Do not attempt to make any repairs to the electric
switches. Take your saw to a MTD Authorized Service
Center.
32.MAINTAIN EXTENSION CORDS. Inspect the exten-
sion cords periodically and replace if damaged. Only
use power cords that are suitably marked for outdoor
use.
33.DO NOT OPERATE YOUR CHAIN SAW near or
around flammable liquids or gases, whether in or out
of doors. An explosion and/or fire may result.
34.This electric powered saw is classified by CSA as a
Class 2C saw. It is intended for infrequent use by
homeowner's, cottagers and campers, and for such
general applications such as clearing, pruning, cutting
firewood, etc. It is not intended for prolonged use. If
the intended use involves prolonged periods of opera-
tion, this may cause circulatory problems in the user's
hands due to vibration. It may be appropriate to use a
saw having an anti-vibration feature.
35.NEVER REMOVE, modify or make inoperative any
safety device furnished with your unit.
36.Safety clothing required by your safety organizations,
government regulations, or your employer should be
used; otherwise, snug fitting clothing, safety footwear,
and hand and ear protection should be worn.
37.When felling, keep at least 2 tree lengths between
yourself and your fellow workers.
38.All chain saw service, other than the items listed in the
user manual safety and maintenance instructions,
should be performed by competent chain saw person-
nel. Do not attempt to repair it yourself; there are no
user serviceable parts inside.
NOTE: Low-kickback saw chain is chain that has met the
kickback performance requirements of ANSI B175.1-1991
and is in accordance with CSA Z62.3. Do not use other
replacement chain unless it has met these requirements for
your specific model.
39.
DO NOT USE ANY OTHER CUTTING ATTACH-
MENT OR ACCESSORIES. Use only MTD
replacement parts and accessories, which are designed
specifically to enhance the performance and maximize
the safe operation of our products. Failure to do so may
cause poor performance and possible injury. Use only
the chain and bar supplied with this product. Do not use
any other cutting attachment. Use of such attachments
will void your factory warranty and could result in serious
bodily injury.
8