Elecom M-BT6BL Series User Manual

Do not drop or hit this product.
If this product is damaged, immediately stop using the
product and turn the mouse body off, and remove the battery
from the mouse.
If you continue to use the product under these conditions, it
may cause a fire or electric shock.
Do not attempt to disassemble, modify or repair this product by
yourself, as this may cause a fire, electric shock or product damage.
Do not put this product in fire, as the product may burst,
resulting in a fire or injury.
Bluetooth® Do not place this produc t in any of the following
environments:
• In a car exposed to sunlight, a place exposed to direct
Laser Mouse
sunlight, or a place that becomes hot (around a heater, etc.)
• In a moist place or a place where condensation may occur
M-BT6BL Series
• In an uneven place or a place exposed to vibration
•
In a place where a magnetic field is generated (near a magnet, etc.)
• In a dusty place
User's Guide
This product does not have a waterproof structure. Use and
store this product in a place where the product body will not
be splashed with water or other liquid.
Rain, water mist, juice, coffee, steam or sweat may also cause
product damage.
When you no longer need to use this product and the
battery, be sure to dispose of it in accordance with the local
ordinances and laws of your area.
Thank you for purchasing the ELECOM M-BT6BL Series Bluetooth® Laser
Mouse. The M-BT6BL is a wireless laser mouse that employs Bluetooth® Batteries
„ „
wireless technology. It is equipped with Back and Forward buttons that are
handy for browsing the Internet, as well as a resolution adjustment button
for changing mouse speed.
Use AAA alkaline batteries, AAA manganese batteries, or
This manual describes the operating instructions and safety precautions
rechargeable AAA nickel hydride battery with this product.
for using the M-BT6BL Series. Ensure that you have read this manual before
using the product. After reading this manual, store it somewhere safe for
If this product will be unused for a long period of time,
future reference.
remove the battery to avoid battery leakage and failure.
* Except in certain cases, the M-BT6BL Series is referred to as "this product" in
this manual.
Cleaning the Mouse
„ „
If the product body becomes dirty, wipe it with a soft, dry cloth.
Use of a volatile liquid (paint thinner, benzene, alcohol, etc.)
may affect the material quality and colour of the product.
Cautions for Wireless Equipment
This product is wireless equipment using the entire range
of the 2.4 GHz band and it is possible to avoid the band of
mobile object identification systems. FH-SS is used for the radio wave method. The
interference distance is 10 m.
Meaning of symbols The 2.4 GHz band is also used by medical equipment, Bluetooth, and wireless LAN
„ „
equipment conforming to the IEEE802.11b/11g /11n standard.
Failure to observe precautions may result in
• Before using this product, check that there are no other "radio
WARNING
serious personal injury or death due to fire,
stations"* operating nearby.
electric shock, or other causes.
• If electromagnetic interference occurs between this product and
Failure to observe precautions may result in other "radio stations", move this product to another location or stop
CAUTION
personal injury due to electric shock or other using this product.
* Other "radio stations" refer to industrial, scientific and medical devices using the
causes, and may damage other equipment.
2.4 GHz band like this product, other radio stations of this type, licensed radio
Prohibited action station premises for mobile object identification system that is used in factory
production lines, certain non-licensed low power radio stations and amateur
Mandatory action
radio stations.
Situation that needs attention
Notes and reference information
● Do not use this product with a device that may have a serious
Information that is handy to know
function or influence. There are rare cases where an external
radio wave at the same frequency or the radio wave emitted
from a mobile phone causes this product to malfunction, slow
Package Contents
down, or fail to operate.
●
Do not use this product in a hospital or other locations where
This product's packaging contains the items listed below. Before using
the use of radio waves is prohibited. The radio waves of this
the product, check that all items are present. We make every effort to
product may affect electronic and medical devices (e.g.
ensure that all products are packaged correctly. However, in the event
pacemaker).
that an item is missing or damaged, contact the retailer from whom you
● The use of a wireless mouse in an aircraft is prohibited by
purchased the product.
aviation law because doing so may interfere with flight safety.
•
Mouse x1 Turn off the power of the mouse body before boarding an
• AAA alkaline battery x2 aircraft and do not use it in the aircraft.
• User's Manual x1 * ELECOM is not liable for any accident or social damages
incurred by the failure of this product.
Safety Precautions
Cautions for Laser Mouse
Observe these precautions carefully to avoid personal injury, damage,
fire, and other problems.
Though this product complies with the IEC60825-1 Class 1 laser safety
standard to ensure safety, pay special attention to the following before use.
WARNING
(1) Never observe the laser beam by using an optical measure such as
If a foreign object (water, metal chip, etc.) enters the product,
a microscope or magnifier or view the laser with the naked eye for
immediately stop using the product, and remove the battery
a long period of time. Doing so may have an adverse effect on the
from the mouse. If you continue to use the product under
eye. (Some laser beams cannot be seen with the naked eye.)
these conditions, it may cause a fire or electric shock.
(2) Never aim the rear surface of the mouse at a person's eyes, as this is
very dangerous.
If an abnormality is found with this product (emission of heat,
(3) The laser sensor may not work on glass or mirrored surfaces.
smoke or abnormal smell from the product), immediately stop
(4) Do not use this product for any application other than as a PC
using the product, shutdown the PC, and after thoroughly mouse.
checking that heat from the product will not cause burns,
(5) I f this produc t is subjec ted to temperatures beyond its
remove the battery from the mouse. After doing this, contact
specifications, turn off the PC, and do not use the product until the
the retailer from whom you purchased the product. temperature returns to the operable range.
(6) If this product is not operating normally, turn off the PC.
WARNING Part Names





CAUTION
a Wheel
The wheel can be turned back and forward with your finger or pressed
like a button to operate the PC.
 Right button
Used for right-click operation.
 Left button
Used for left-click operation.
d Remaining battery level indicator lamp/ Resolution
switch indicator lamp/pairing indicator lamp
y Turns red when the mouse is in a pairing standby state.
y Indicates when to replace the batteries.
* When a battery has been inserted, if there are sufficient
remaining battery levels, it will illuminate in red for a certain
period of time, and if low, it will flash continuously. If the
remaining battery level becomes low during use, it will flash
continuously in red for a certain period of time.
y Flashes when the resolution (mouse cursor speed) is changed.
* Flashes twice when switching from 800 to 1600
CAUTION
Flashes once when switching from 1600 to 800
e Pairing button
Pairs the mouse with a PC Bluetooth module or a Bluetooth adapter.
f Power switch
Used to turn the mouse body on and off.
g Laser sensor
When the mouse body is moved, this sensor detects mouse
movement.
* Never observe the laser beam using an optical means such as a
microscope or magnifying glass or view the laser with the naked
eye for a long period of time. Doing so may damage the eyes.
(Some laser beams cannot be seen with the naked eye.)
h Battery cover
This cover is removed to install batteries.
There is battery housing inside, batteries are inserted there.
i Resolution switch
Switches the resolution (mouse cursor speed) between 800 and 1600
each time the button is pressed.
Initial Setup Procedure
When using this product for the first time, operate and configure this
product and the PC in the order shown below.
• To use this product, your PC must support the Bluetooth HID
profile or have a Bluetooth adapter connected.
• Do not remove your existing mouse until this product is
successfully connected. You need to use your existing mouse
WARNING
to configure the PC.
1
Insert the batteries
2
Turn on the power
3
Pair the mouse with the PC
4
Check mouse operation
1
Installing / Replacing the Battery

 Before using this product, install two AAA batteries in the mouse body.

Remove the battery cover.
(Bottom)

Hook a nger on part  to remove
 the cover easily.
Insert the batteries.
Make sure that the polarity is correct.
y
Install the battery cover as
before.
Replacing the Battery
„ „
When batteries are drained, replace them following the instructions below.
Remove the battery cover.

Hook a nger on part  to remove
the cover easily.
Remove the batteries.
Insert the battery.
Do not mix different types of batteries or use old
y
batteries with new batteries to avoid battery leakage
and failure.
Install the battery cover as before.
2
Turning on the mouse
* Refer to the back of this sheet.
When using this product, turn the mouse body power on.
Slide the power switch to the ON position.
The remaining battery level indicator lamp is
illuminated in red for a certain period.
When not using this product, turn the mouse
body off to save battery power.
Slide the power switch to the OFF position.
Restoring from sleep state
„ „
Click the right mouse button.
To reduce battery drain, the mouse enters sleep mode automatically
if it is left without being operated for a certain period of time with
the power or switch turned on.
- 1 -
3
Pairing the Mouse with the PC
To connect this product to the PC using Bluetooth, you need to pair the product with the PC.
• Pairing involves registering Bluetooth devices (in this case, the mouse and the PC) with each other, and authorising a connection with a registered
device.
•
Use your existing mouse or touch pad to operate the PC until the pairing process is completed successfully.
When using Windows®
Windows Vista® (–SP1) and Windows® XP
This section describes the procedure when using the standard „ „
Windows® Bluetooth function.
* Screen appearance may change depending on operating system, but
Windows® 7 and Windows Vista® SP2 the procedure is the same.
„ „
I n t h e t a s k t r a y o r t h e
* Screen appearance may change depending on operating system, but
the procedure is the same. notification area, right-click the
Bluetooth icon (
In the notification area,
[Add a Bluetooth Device].
click , then right-click
the Bluetooth icon ( )
The [Add Bluetooth Device
and click [Add a Device]. Wizard] is displayed.
The [Add a Device] window
is displayed.
Select the [My device is set
up and ready to be found.]
• If the is displayed in the notification area in Windows® 7,
check box and then click
right-click and then click [Add a Device].
• If no icon is displayed, click the [Start] button, click
[Control Panel], and then click [Add a Device].
The system starts searching for
Bluetooth devices to add.
Press the pairing button
on this product.
Hold down the pairing button
on this product while the
torch icon (
The pairing indicator lamp turns
on during the pairing procedure
and turns off when the procedure
The pairing indicator lamp turns
is complete (step ).
Pairing button on during the pairing procedure
and turns off when the procedure
is complete (step
If this product is not displayed in the list, check that its
power is turned on, press the pairing button, and then
click .
Click [ELECOM BLUETOOTH
LASER MOUSE] and then click
.
Click [ELECOM BLUETOOTH
Product registration starts.
LASER MOUSE] and then
click
Click .
Select [Don't use a passkey],
and click
Product registration starts.
[ELECOM BLUETOOTH LASER
MOUSE] is added to the [Bluetooth
Devices] window.
Click
You can now use the mouse.
Refer to "4. Checking Mouse Operation" on the back of this sheet to
confirm that the mouse works correctly.
[ELECOM BLUETOOTH LASER MOUSE] is added
to the [Bluetooth Devices] window.
Click
You can now use the mouse.
Refer to "4. Checking Mouse Operation" on the back of this sheet to
confirm that the mouse works correctly.
) and click
If the icon is not displayed, click the [Start] button, click
[Control Panel], click [Hardware and Sound], and then
click [Bluetooth Devices]. When the [Bluetooth Devices]
window is displayed, click [Add].
.
is displayed.
).
Pairing button
If this product is not displayed in the list, check that its
power is turned on, press the pairing button, and then
click .
.
.
.
.