Specialized Turbo Elite Instruction Manual

Specialized Turbo Elite Instruction Manual

Specialized 2004 turbo elite cyclocomputer instruction manual

Advertisement

2004 TURBO® ELITE
CYCLOCOMPUTER
Congratulations on your purchase! You are now the
owner of one of the world's most advanced cyclocomput-
ers. Your Specialized Turbo® Elite features a wireless
speed transmitter and a wired cadence sensor.
Additionally, it incorporates a revolutionary new backlit
three-line LCD screen. The large, easy to read, digits
allow you to view two functions simultaneously and the
alphanumeric dot matrix display provides a quick refer-
ence to the currently displayed function. The Turbo® Elite
has been designed to provide the best combination of
performance, features, durability and ease of use.
3
7
4
5
6
8
2
1
FIGURE 1
This illustration describes the screen display
and buttons
MODE/SET rocker switch
TOP Button (Backlight & Start/stop)
Dot-matrix Display Area
Digital Display Area
Wheel Option Indicator
MPH or KM/H indicator
1

Advertisement

Table of Contents
loading

Summary of Contents for Specialized Turbo Elite

  • Page 1 CYCLOCOMPUTER Congratulations on your purchase! You are now the owner of one of the world’s most advanced cyclocomput- ers. Your Specialized Turbo® Elite features a wireless speed transmitter and a wired cadence sensor. Additionally, it incorporates a revolutionary new backlit three-line LCD screen.
  • Page 2 Magnet with screw (1) Lap-timer Adhesive backed magnet FIGURE 2 • CAD – Cadence • AVCAD – Average Cadence magnet (1) CR2032, Specialized wheel circumference set- Cadence Cable tie wraps (10) P/N 481-3004) with the tings before removing it. • MXCAD – Maximum...
  • Page 3: Mounting

    the case with a coin. ambient temperatures are (See figure 5). computer forward onto the below 40 °F (4 °C). To mount until it ‘snaps’ into FIGURE 3: BATTERY reduce signal loss in colder For wheels with place with an audible INSTALLATION temperatures, the transmit- bladed spokes:...
  • Page 4: Operation And Programming

    cadence option you must crank arm. (See figure 8). modes available: 1) Clock install the cadence wire Do not tighten the tie-wrap Mode, 2) Distance Mode, CLOCK provided with your Turbo® until final placement of the 3) Speed Mode, 4) Timer magnet is correct.
  • Page 5 14 play only kilometers. (See This mode is useful if you entered as your existing Specialized tire sizes: “Setting the Display have replaced the battery 26 X 1.0 Language” above). To and would like to retain 26 X 2.2...
  • Page 6 This chart is for non- ters. Press the “MODE” FIGURE 11 place the valve at the 6:00 Specialized tires button until the flashing for three seconds. The position (at the bottom) 26 X 1.75 digit is correct. (Note: The...
  • Page 7 ence for wheel option #2. the “SET” button to confirm Follow the same procedure your selection. The hour The TIMER function is just 7. Interval Timer (INT) to program the wheel #2 digit will now begin flash- like a conventional stop- tire size and tap the “SET”...
  • Page 8 COMPUTER programmed, press the Dot-matrix Display Area. FUNCTIONS “TOP” button to start/stop Note: if your display says the countdown. (See fig- “INT, press the “SET” but- ure 15). Note: The shortest ton to change to “DISTÚ” Speedometer (SPEED)- interval that can be set is 5 To set the Distance Your current speed is seconds.
  • Page 9 when the “TOP” button is Cadence (CAD)- Trip Distance (DST)- The total distance is shown pressed. The stopwatch will Cadence mode will display Trip distance mode will on the lower line if the record the total time after your pedaling speed in record up to 999.99 miles screen.
  • Page 10 • See your authorized Stopwatch (TM) the backlight is on, the cur- when it was parked? If so, Specialized dealer if you 0 to 9hrs, 59min, 59sec. rent-speed display will be move the bike to the shade. have any trouble installing recycling type frozen.
  • Page 11 If within two authorized to assume any liability (2) year from the date of that orig- WWW.SPECIALIZED.COM on behalf of Specialized Bicycle inal purchase, this product is found Components, Inc. in connection to be defective in material or work- DESCRIPTION PART# with the sale of this product.

Table of Contents