Lamp Replacement - Dimplex SP1 Wallfire User Manual

The Standby switch must first be turned 'ON' to operate the
heater manually or by remote control.
Note: It takes some time for the receiver to respond to the
transmitter. DO NOT PRESS the buttons more than once within
two seconds for correct operation.
To go to the previous settings press the
Pressing the button on the remote turns off the light &
settings. To resume press the button until the desired setting
is reached - see Fig. 8.
To increase or decrease the brightness of the flames, use the
dimmer button or the
heat setting will remain the same.
To turn off the power the Standby Switch must be turned 'OFF'.
Instructions for fitting pebbles - SP8 only
The SP8 model is provided with a pebble fuel effect. To fit follow
the instructions given below.
Warning - The pebbles should only be placed on to the fuel
effect once the fire has been fully secured to the wall.
This should only be done when the appliance is switched
off.
The front panel will need to be removed in order to place the
pebbles on the fuel bed.
Warning - The front panel is heavy and easily damaged.
1. Remove the two screws which hold the front panel in place -
see Fig. 9.
2. While holding the front by its sides with both hands carefully
tilt forwards and then lift up and out - see Fig. 9b.
3. Place the front panel flat on a protective surface such as a
matt with the glass facing away from the floor.
4. Remove the pebbles from the packaging and arrange on the
fuel bed.
5. Refit the front panel ensuring that its base is held in place i.e.
that it slots into the channel on the frame (see Fig. 10c) reversing
the steps as outlined previously.

Lamp Replacement

WARNING – ALWAYS DISCONNECT FROM THE POWER
SUPPLY BEFORE REMOVING LAMPS.
Warning - The lamps reach high temperatures during operation.
For this reason, allow the lamps to cool down after switching off
the appliance.
The front panel will need to be removed in order to change lamps
– see Fig. 9.
Warning - The front panel is heavy and easily damaged.
The front panel is fixed with two screws on top and is supported
underneath by the chassis see Fig. 9.
Care is needed to avoid the front panel falling forward while
removing the screws see Fig. 9a.
While holding the front by its sides with both hands carefully tilt
forwards and then lift up and out - see Fig. 9b.
Place the front panel flat on a protective surface such as a matt
with the glass facing away from the floor.
To gain access to lamps please apply the following procedure:
Remove two screws securing fuel effect. Holding the logs
carefully lift up (1) and out (2) for SP1,2 & 3 models - see Fig.
10.
For the SP8 model remove the pebbles and carefully place to
one side.
Carefully slide the flexible rotisserie (see Fig. 11a) to one side
ensuring that the rubber grommet is not lost – see Fig. 11b.
Remove the defective lamp by unscrewing it (see Fig. 12).
Replace with a 60W E14 SES Clear Candle bulb, rotating it.
button.
button on the Remote Control. The
Take care not to over-tighten the lamp.
Steps for reassembling the heater
1. Refit the rotisserie making sure that the rubber grommet is
carefully pushed into the slotted hole on the axial bracket (see
Fig. 11c).
2. Refit the fuel effect ensuring that the fuel effect bracket (see
Fig. 10b) on the fuel effect slots in between the fuel effect
heat
retaining bracket and the inner glass (see Fig. 10a).
3. Refit the front panel (ensuring that its base is held in place i.e.
that it slots into the channel on the frame (see Fig. 10c) reversing
the steps as outlined previously.
Thermal Safety Cut-out
For your safety, this appliance has been fitted with thermal cut-
out. In the event that the product overheats, the cut-out switches
the heat off automatically.
To bring the heat back into operation, remove the cause of the
overheating, then unplug or turn off the electrical supply to the
heater for up to 10 minutes.
When the heater has cooled sufficiently, re-connect and switch
on the heater.
Caution: In order to avoid a hazard due to inadvertent resetting
of the thermal cut-out, this appliance must not be supplied
through an external switching device, such as a timer, or
connected to a circuit that is regularly switched on and off by
the utility.
Cleaning
WARNING – ALWAYS DISCONNECT FROM THE POWER
SUPPLY BEFORE CLEANING THE HEATER.
For general cleaning use a soft clean duster – never use
abrasive cleaners. The glass viewing screen should be
cleaned carefully with a soft cloth. DO NOT use proprietary
glass cleaners.