Hilti DEG 500-D Operating Instructions Manual
Angle grinder
Hide thumbs
Also See for DEG 500-D:
- Operating instructions manual (18 pages) ,
- Operating instructions manual (20 pages) ,
- Operating instructions manual (18 pages)
Subscribe to Our Youtube Channel
Related Manuals for Hilti DEG 500-D
Summary of Contents for Hilti DEG 500-D
- Page 1 DEG 500-D/ DEG 600-D/-P Operating instructions Mode d’emploi Manual de instrucciones Manual de instruções Printed: 07.07.2013 | Doc-Nr: PUB / 5138162 / 000 / 00...
- Page 2 +≠ +± This Product is Certified Ce produit est homologué Producto homologado por Este produto está registrado Printed: 07.07.2013 | Doc-Nr: PUB / 5138162 / 000 / 00...
- Page 3 Printed: 07.07.2013 | Doc-Nr: PUB / 5138162 / 000 / 00...
- Page 4 Printed: 07.07.2013 | Doc-Nr: PUB / 5138162 / 000 / 00...
-
Page 5: Table Of Contents
ORIGINAL OPERATING INSTRUCTIONS DEG 500‑D/DEG 600‑D/‑P angle grinder 1 These numbers refer to the corresponding illustra- It is essential that the operating instructions tions. The illustrations can be found on the fold-out cover are read before the power tool is operated for pages. -
Page 6: Description
The tool may be used only for dry cutting or grinding. Cutting or grinding materials containing asbestos is not permissible. When grinding stone, a vacuum cleaner equipped with a stone dust filter, e.g. a suitable Hilti vacuum cleaner, must be used. - Page 7 Observe the information printed in the operating instructions concerning operation, care and maintenance. The power tool is designed for professional use and may be operated, serviced and maintained only by trained, authorized personnel. This personnel must be informed of any special hazards that may be encountered. The power tool and its ancillary equipment may present hazards when used incorrectly by untrained personnel or when used not as directed.
-
Page 8: Insert Tools, Accessories
Abrasive cutting disc AC-D Universal Super Premium Abrasive grinding disc AG-D Universal Super Premium Diamond cutting discs DC-D 150/6" Items not supplied by Hilti Designation Wire brushes Rubber backing pads Accessories for the DEG 500 and DEG 600 Designation Guard with side cover... -
Page 9: Technical Data
4 Technical data Right of technical changes reserved. Tool DEG 500-D DEG 600-D/-P Rated current input Rated voltage 120 V: 11.5 A Rated voltage 120 V: 11.5 A Rated frequency 60 Hz 60 Hz Rated speed 11,000/min 9,300/min Cutting discs (Ø) 125 mm (5") - Page 10 the tool. Carrying power tools with your finger on the 5.2 Additional safety instructions switch or energising power tools that have the switch 5.2.1 Safety warnings common for grinding, on invites accidents. danding, wire brushing, polishing or abrasive d) Remove any adjusting key or wrench before turn- cutting-off operations ing the power tool on.
- Page 11 of workpiece or of a broken accessory may fly propel the tool in direction opposite to the wheel’s away and cause injury beyond immediate area of movement at the point of snagging. operation. d) Use special care when working corners, sharp Hold the power tool by insulated gripping surfaces edges etc.
- Page 12 Hilti Service d) Avoid touching rotating parts. Switch the power Center. tool on only after bringing it into position at the Take steps to ensure that flying sparks from the workpiece.
-
Page 13: Before Use
Dirty or dusty power tools which have been used frequently for work on conductive materials should be checked at regular intervals at a Hilti Service Center. Under unfavorable circumstances, dampness or dust adhering to the surface of The user and any other persons in the vicinity must wear ANSI Z87.1-approved eye protection, a hard... -
Page 14: Operation
Do not use the power tool if it starts with a jolt.This may be an indication that the electronic control unit is WARNING defective. Have the tool repaired at an authorized Hilti Breathing protection must be worn if the power tool service center right away. -
Page 15: Care And Maintenance
Have insulation. Under such conditions, the tool should be the power tool repaired by Hilti Service. plugged into a ground fault circuit interrupter (GFCI) and use of a stationary dust removal system and WARNING frequent cleaning of the tool’s cooling air slots is... -
Page 16: Disposal
10 Disposal Most of the materials from which Hilti power tools or appliances are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, Hilti has already made arrangements for taking back your old power tools or appliances for recycling. - Page 17 Fax:+423 / 234 29 65 www.hilti.com 3 609 929 B10 Hilti = registered trademark of Hilti Corp., Schaan W 3105 | 0313 | 10-Pos. 3 | 1 Printed in Germany © 2013 Right of technical and programme changes reserved S. E. & O 285964 / A2 Printed: 07.07.2013 | Doc-Nr: PUB / 5138162 / 000 / 00...
Need help?
Do you have a question about the DEG 500-D and is the answer not in the manual?
Questions and answers