Sony SRW-5000 Operation Manual page 84

4-4 CUE Menu
4
Press the [F7] (SET LETTER) button or the center
cursor button.
The selected character is entered.
F O R M A T
R E C D A T E [ 2 0 0 3 / 0 2 / 2 5 ]
T - F i l
T I T L E [ S O N Y
N o . I N
U N D O
A L L
0 0 0 : 0 0 : 0 4 : 0 5
1 0 0 : 0 3 : 4 5 : 2 1 0 1 : 0 0 : 3 6 : 0 6 5 9 i 1 0 8 0
A T T R I B
2 0 1 : 0 4 : 2 7 : 2 3 0 1 : 0 5 : 3 1 : 2 4 5 9 i 1 0 8 0
E D I T
3 - - : - - : - - : - - - - : - - : - - : - - - - - - - - -
C O P Y
t o C U E
T - F i l W R I T E
M O D E P R T E C
p a n e l o f f
5
Repeat steps 3 and 4 to enter more characters.
To enter a space
Press the [F5] (SPACE) button.
If you enter a wrong character
Press the [F6] (BACK SPACE) button to go back.
Then re-enter the character.
To start the procedure over again
Press the [F9] (CANCEL) button to start again.
To change a character
Press the cursor R button to move the cursor to the
title box. Then press the cursor T or t button to
change the insertion position.
If entered title exceeds the length of the title box
t or T appears to the left or right of the box.
6
Press the [F10] (SAVE/EXIT) button.
The screen that was on before the title was entered
is displayed again.
To change IN/OUT point time data
1
Use the cursor buttons to move the cursor (B) to
the line where you want to change IN/OUT point
time data.
4-44
Chapter 4 Menu Settings
E O S [ - - : - - : - - : - - ]
] R a s t 8 5 %
O U T T a p e F o r m a t
0 0 : 0 0 : 0 9 : 2 3 5 9 i 1 0 8 0
W R I T E
E X I T
To move the cursor using the numeric buttons
With the cursor specifying IN or OUT, enter the
line number using the numeric buttons. Then press
the [F9] (CUENUM POINT) button. The cursor
will move to the line specified by the numeric
buttons.
Note
If the cursor (B) is not linked with the cursor
buttons, the cursor (B) will not move when the
cursor buttons are pressed.
To link the cursor (B) with the cursor buttons
Press the center cursor button. Each press of the
button alternately links and unlinks the cursor B.
2
Press the ENTRY button.
When the cursor buttons are aligned with the IN
point, and the IN point is at the OUT point, when
you press the ENTRY button at the OUT point, the
time code is either entered as a new value or
updated. To update the data, the winding diameter
measurement must be completed, and the drum
locked, and then the tape information read in.
Note
If the cursor (B) is not on the screen when the
ENTRY button is pressed, the time data on the line
currently specified by the cursor (B) changes to the
current time data, and the line is automatically
displayed.
To clear the data
With the cursor buttons, align the cursor with the data
you want to clear, and in the case of the IN point hold
down the IN button, and in the case of the OUT point
hold down the OUT button, and press the CLR button,
to clear the data.
You can also clear the data by holding down the CLR
button, and pressing the IN button or OUT button.
Effect on other data of data entry or update
When you enter or update the IN point or OUT point,
other data is updated as shown in the following table.