Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Tecnoware EXA LCD 1.5
Summary of Contents for Tecnoware EXA LCD 1.5
-
Page 1: Uninterruptible Power Supply
Uninterruptible Power Supply EXA LCD 1.5 EXA LCD 2.0 EXA LCD 2.6 User’s manual... -
Page 3: Table Of Contents
Edition: April 2013 – version: 1.0 No part of this manual may be reproduced, even partially, without the authorisation of TECNOWARE s.r.l. TECNOWARE s.r.l. reserves the right to change specifications at any time and without notice. UPS EXA LCD 1.5 – 2-0 – 2.6... -
Page 4: Safety Warnings
Safety Warnings Read this manual carefully and completely before installing and using the TECNOWARE EXA LCD Uninterruptible Power Supply, which, from here after, will also be referred to as UPS. This manual should be kept close to the UPS and read before the UPS is installed and used. -
Page 5: Introduction
• EXA LCD 1.5 (1.5 KVA) • EXA LCD 2.0 (2.0 KVA) • EXA LCD 2.6 (2.6 KVA) In this manual EXA LCD will simply be referred to as UPS. UPS EXA LCD 1.5 – 2-0 – 2.6 User’s manual... -
Page 6: General Characteristics
Do not keep liquids, flammable gases or corrosive substances near the unit. • Install the UPS on a properly tiled floor. Avoid the installation on a floor that is not tiled flat. • User’s manual UPS EXA LCD 1.5 – 2-0 – 2.6... -
Page 7: External Description
LCD display provides information about Input and Output Voltage, Battery Level percentage, Load Level percentage, functioning modes, alarm and fault conditions. ON/OFF button: enables the user to turn ON/OFF the UPS. Figure 1 – Front panel UPS EXA LCD 1.5 – 2-0 – 2.6 User’s manual... -
Page 8: Lcd Display
BATTERY MODE: this icon is on to indicate the UPS is working in Battery mode. LOW BATTERY: is on to indicate the Low Battery condition. OVER LOAD: is on to indicate the Overload condition. FAULT: is on to indicate the Fault condition. User’s manual UPS EXA LCD 1.5 – 2-0 – 2.6... -
Page 9: Rear Side
Grounded AC Input power socket: IEC C14 type; to connect the UPS to the AC utility line. Input fuse: electrical specification: max current 10 A (EXA LCD 1.5 – 2-0) or max current 15 A (EXA LCD 2.6), voltage 250 V. -
Page 10: Electrical Installation And First Start Up
There are no internal parts in the UPS that are user serviceable. Any repair or maintenance work must be performed exclusively by qualified technical personnel authorized by TECNOWARE. TECNOWARE declines any responsibility if this warning is disregarded. Disregard for these warnings may lead to a risk of electric shock to operators. -
Page 11: Functioning
After a complete discharge, the UPS needs 4 hours to recharge completely the batteries. The UPS recharges batteries automatically if it works in Normal mode or if it is off and connected to the AC Input Line. UPS EXA LCD 1.5 – 2-0 – 2.6 User’s manual... -
Page 12: Load Control
The RS-232 and USB signals are all isolated through photo-couplers from the dangerous voltages that are present inside the UPS. Connecting to the Web site www.tecnoware.com, it is possible to download, free of charge, the update UPS management Software ViewPower, compatible with the most popular Operative Systems. -
Page 13: Technical Characteristics
14,5 x 20 x 38 cm Net Weight 13,8 Kg 14,2 Kg 16 Kg Technical data may change without prior notice (*) Connect the printers to the ONLY FILTERED Output sockets UPS EXA LCD 1.5 – 2-0 – 2.6 User’s manual... -
Page 14: Maintenance
The recommended environmental specifications for a correct use of batteries are listed in the “Technical Specifications” section. Battery Replacement Figure 4 – Battery Replacement User’s manual UPS EXA LCD 1.5 – 2-0 – 2.6... -
Page 15: Operator Safety
Reassemble the battery cover and then the front panel. Battery replacement must be performed exclusively by qualified technical personnel authorized by TECNOWARE. TECNOWARE declines any responsibility if this warning is disregarded. When replacing batteries, replace with the same type and number. -
Page 16: Troubleshooting
TECNOWARE. TECNOWARE declines any responsibility if this warning is disregarded. Warning to the technical personnel authorized for service: since internal components are connected to the batteries, they will remain powered, and therefore dangerous, even after the UPS has been disconnected from AC power mains. -
Page 17: Conformity To The European Directives
Conformity to the European Directives TECNOWARE S.r.l. confirms that EXA LCD models comply with the requirements set out in: the Low Voltage Directive (Safety) 2006/95/EC and following amendments, the EMC (Electro-Magnetic Compatibility) Directive 2004/108/EC and following amendments. The following standards were applied:... - Page 20 TECNOWARE s.r.l. www.tecnoware.com...