Switching The Speaker System - Pioneer sc-9540 Operating Instructions Manual

09 Using other functions
4 Press RETURN to confirm and exit the menu.
Setting What it does
Converts video signals for output
V.CONV
(Digital Video from the MONITOR OUT jacks
Conversion) (including HDMI OUT connector)
for all video types (see page 25).
Specifies the output resolution of
a
RES
the video signal (when analog
(Resolution)
video input signals are output at
the HDMI OUT connector, select
this according to the resolution of
your monitor and the images you
wish to watch).
b Specifies the aspect ratio when
ASP
analog video input signals are
(Aspect)
output at the HDMI output. Make
your desired settings while
checking each setting on your
display (if the image doesn't match
your monitor type, cropping or
black bands appear).
c,d This setting optimizes the picture
PCINEMA
for film material when the video
(PureCinema)
output is set to progressive.
Usually set to AUTO; but try
switching to OFF if the picture
appears unnatural.
Additionally, certain PAL movie
video (576i, 25 frames/second STB
video output or DVD disc playback,
etc.) that contain film progressive
material cannot be recognized as
such by this receiver.
c,d Adjusts the motion and still picture
P.MOTION
quality when video output is
(Progressive
progressive.
Motion)
c Adjusts the amount of noise
YNR
reduction (NR) applied to the Y
(brightness) component.
Adjusts how sharp edges appear.
c
DETAIL
c,e Adjusts the sharpness of the high-
SHARP
frequency (detailed) elements in
(Sharpness)
the picture.
c Adjusts the overall brightness.
BRIGHT
(Brightness)
Adjusts the contrast between light
c
CONTRAST
and dark.
c,f Adjusts the red/green balance.
HUE
Note
1 • The subwoofer output depends on the settings you made in Manual speaker setup on page 108. However, if SPB is selected above, no sound
is heard from the subwoofer (the LFE channel is not downmixed).
• Depending on the settings in Surround back speaker setting on page 109 output from the surround back pre-out terminals may change.
• All speaker systems (except Speaker B connections) are switched off when headphones are connected.
84
en
Setting
Option(s)
CHROMA
(Chroma
ON
Level)
OFF
a.• When set to a resolution with which the TV (monitor) is not
compatible, no picture is output. Also, in some cases no picture will
AUTO
be output due to copyright protection signals. In this case, change
the setting.
PURE
• When AUTO is selected, the resolution is selected automatically
480p/576p
according to the capacity of the TV (monitor) connected by HDMI.
When PURE is selected, the signals are output with the same
720p
resolution as when input (At this time, video signals are only output
1080i
from the same type of terminals to which they were input).
• When a display is connected by HDMI, if this is set to something
1080p
other than PURE and 480i/576i analog signals are input, 480p/576p
THROUGH
signals are output from the component output terminals.
• Conversion to 1080p is only performed for 480i, 576i, 480p and
NORMAL
576p input signals.
b.• If the image doesn't match your monitor type, adjust the aspect
ratio on the source component or on the monitor.
• This cannot be set when the resolution is set to PURE.
• NORMAL setting is only displayed when 480i/p or 576i/p video
signals are being input.
c.This setting is only displayed when 480i or 576i video signals are
being input.
AUTO
d.This setting is only valid for component outputs.
PAL
e.This setting is not valid for HDMI outputs.
f. This setting is not displayed for component inputs.
OFF

Switching the speaker system

If you selected Speaker B in Surround back speaker
setting on page 109, three speaker system settings are
possible using SPEAKERS. If you selected Normal, Front
Bi-Amp or ZONE 2, the button will simply switch your
main speaker system on or off. The options below are for
–4 to +4 the Speaker B setting only.
set to
Default: 0
0 to +8
Default: 0
–4 to +4
•
Default: 0
speaker system setting.
–4 to +4
As mentioned above, if you have selected Normal, the
Default: 0 button will simply switch your main speaker system (A)
on or off.
–6 to +6
Press repeatedly to choose a speaker system option:
Default: 0
• SPA – Sound is output from speaker system A and
–6 to +6
Default: 0
• SPB – Sound is output from the two speakers
–6 to +6
Default: 0
What it does
Adjusts saturation from dull to
c
bright.
1
AUDIO PARAMETER VIDEO
(TUNE)
TUNER EDIT BAND AUTO SURR/ALC/ HOME
STREAM DIRECT THX
(PRESET) ENTER (PRESET)
HDMI 4
(TUNE)
HOME MENU RETURN VIDEO CAMERA
Use SPEAKERS on the front panel to select a
the same signal is output from the pre-out terminals.
connected to speaker system B. Multichannel
sources will not be heard. The same signal is output
from the surround back channel pre-out terminals.
Option(s)
–6 to +6
Default: 0
CONTROL ON/OFF
STANDARD ADVANCED STEREO MULTI-ZONE SPEAKERS
SURROUND SURROUND
iPod
iPhone
USB MCACC
SETUP MIC PHONES