SkyLink MOTION ALERT HA-318 User Manual

Motion Alert
1. INTRODUCTION
The Motion Alert is designed to monitor movement around your
house. The motion sensor can be placed either indoor or outdoor.
Once motion is detected, the receiver will beep & flash.
In this package, you should find an Indoor/Outdoor Motion Sensor, a
Houselink ® Receiver, an adapter, ball-head joint, screws and a clip.
Ball-head joint
Indoor/Outdoor
Motion Sensor
Adapter
®
Houselink
Receiver
2 pcs 3 x 18 screws Clip
(Included)
Please follow the instructions below to setup your motion sensor
and the receiver.
1. POWER UP
After setting up all the connectors properly, both units are now ready to be powered up.
Insert a 9V alkaline battery (not included) to the motion sensor and its LED will be on for 2 seconds. The
receiver will beep and red LED flash. The sensor requires a warm up time of approx. 45 seconds before
it can function properly. After powering up the sensor, face it to the wall where no motion will be
detected. After 45 seconds, the sensor is ready. Wave your hand in front of the sensor, the receiver will
beep and red LED will flash for
approx. 15 seconds.
Plug in the adapter to the receiver,
the green LED will start flashing
indicating the receiver unit is
powered up but no sensor is
detected.
Plug in the adapter to the receiver
Model HA-318
1. CODE CONNECTORS
In order for the sensor to communicate with the receiver properly,
the sensor's code must match with the receiver's code. Code
connectors 1 to 6 can be found by opening the battery cover and
back cover of the receiver. User is required to set these code
connectors randomly and the code settings on both sensor and
receiver must be the same. Each position of the code connector
can be set to "+", "-' or "0" positions. Refer to the diagram below
to set the code connectors properly.
Code Connectors on Motion Sensor
Note: If you experience interference from a nearby system, which could accidentally trigger your
system, please change the code settings on the sensor and receiver. The code setting on the
sensor and receiver should still match after changing the code setting.
3. POWER UP THE INDOOR/OUTDOOR MOTION SENSOR AND RECEIVER
Insert 9V alkaline battery to the sensor
2. SET UP THE INDOOR/OUTDOOR MOTION SENSOR AND HOUSELINK
Clip
Note: A connector can be
removed with the clip,
as shown.
' '
0
'+'
Code Connectors on Receiver
2. SENSOR SENSITIVITY
The sensitivity of the motion sensor is adjustable. Change the
setting by placing the connector on either the "High" or "Low"
position. When the sensitivity is set to "Low", more movement
is required to trigger the sensor. It is recommended to set the
sensitivity to "Low" and perform a "Walk Test" (Described in
Section 3 - "Walk Test"). If the walk test result is satisfied, the
sensitivity does not require to be adjusted further. If the walk
test result shows the sensitivity is too low, then you can change
the sensitivity setting to
"High". Please perform the
walk test after chang-
ing the sensitivity setting.
Sensitivity Connectors
on Motion Sensor
® RECEIVER
2. ZONE CONNECTORS
Each receiver can work with up to 4 different sensors (to represent 4
different zones on the receiver). There are 2 connectors that determine
the zone number 1, 2, 3 and 4. These 2 connectors can be found by
opening the battery cover. Please follow table 1 to set the zone.
'-'
Zone connectors
"+" in the table means the connector for that position should be placed on
the posts.
"-" in the table means the connector for that position should be removed.
3. MOUNTING
A ball-head joint is necessary to mount the sensor at a desire location.
A height of 5-6 ft is recommended, depending on your application. Once
a location is selected, mount the ball-head joint to this location by screws
provided, (see diagram 1). Once the ball-head joint is mounted to the
wall, slide the back of the sensor into the ball-head joint (see diagram 2).
The mounting angle can be adjusted. Please refer to Section 3 "Walk
Test" to determine the best mounting angle.
Diagram 1
A B
Zone 1 + +
Zone 2 + -
Zone 3 - +
Zone 4 - -
Table 1
Diagram 2