Related Manuals for Compaq 154060-002
Summary of Contents for Compaq 154060-002
- Page 1 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide Second Edition (July 2000) Part Number 154060-002 Compaq Computer Corporation...
- Page 2 All other product names mentioned herein may be trademarks and/or registered trademarks of their respective companies. Compaq shall not be liable for technical or editorial errors or omissions contained herein. The information in this document is subject to change without notice.
-
Page 3: Table Of Contents
SCSI Termination ....................1-4 SCSI Cables......................1-5 SCSI Cable Connectors ................... 1-6 Chapter 2 Installing the Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Items Needed ......................2-1 Preparing the Server ....................2-2 Opening the Server ....................2-2 Installing the 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter....2-2... - Page 4 Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installing the Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter continued Cabling the 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter ....2-3 External SCSI Connections................2-3 Internal SCSI Connections................2-4 Completing the Installation..................
-
Page 5: About This Guide
About This Guide This guide is designed to be used as step-by-step instructions for installation and upgrades to the Compaq StorageWorks 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter. WARNING: To reduce the risk of personal injury from electrical shock and hazardous energy levels, only authorized service technicians should attempt to install this equipment. -
Page 6: Text Conventions
Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Text Conventions This document uses the following conventions to distinguish elements of text: Keys appear in boldface. A plus sign (+) between Keys two keys indicates that they should be pressed simultaneously. -
Page 7: Symbols In Text
About This Guide vii Symbols in Text These symbols may be found in the text of this guide. They have the following meanings. WARNING: Text set off in this manner indicates that failure to follow directions in the warning could result in bodily harm or loss of life. CAUTION: Text set off in this manner indicates that failure to follow directions could result in damage to equipment or loss of information. -
Page 8: Getting Help
A technical support specialist will help you diagnose the problem or guide you to the next step in the warranty process. In North America, call the Compaq Technical Phone Support Center at 1-800-OK-COMPAQ . -
Page 9: Compaq Website
Operating system type and revision level Detailed, specific questions Compaq Website The Compaq website has information on this product as well as the latest drivers and Flash ROM images. You can access the Compaq website at http://www.compaq.com. Compaq Authorized Reseller For the name of your nearest Compaq Authorized Reseller: In the United States, call 1-800-345-1518. -
Page 10: Introduction
Chapter Introduction The Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter contains one low voltage differential (LVD) SCSI channel that interfaces directly between the server Peripheral Component Interface (PCI) Local Bus and up to 15 SCSI devices. The adapter supports industry-standard interfaces and protocols. -
Page 11: Wide Ultra3 Scsi Support
1-2 Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide Contains one 68-pin wide SCSI external connector that supports Wide Ultra3 SCSI, Wide Ultra2 SCSI, Wide-Ultra SCSI-3, and Fast-Wide SCSI-2 Contains one 50-pin narrow SCSI internal connector to support legacy... -
Page 12: Scsi Connectors
Introduction 1-3 SCSI Connectors The 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter has the following connectors: Figure 1-1. 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter 1 Internal 50-pin Narrow SE SCSI legacy connector at J4 (cannot be used simultaneously with 4) 2 TE (Termination Enable) SEC jumper at J6 (should be jumpered) 3 TE (Termination Enable) PRI jumper at J2 (should be left open) 4 Internal 68-pin Wide SE SCSI legacy connector at J5 (cannot be used... -
Page 13: Scsi Ids
6 to 0, then 15 to 8, with 6 being the highest priority and 8 being the lowest priority. SCSI IDs on all peripherals must be either manually set with switches or jumpers on the device itself, or automatically set on Compaq products that support hot-pluggable drives. The SCSI IDs determine the priority of the peripheral device when attempting to access the SCSI bus. -
Page 14: Scsi Cables
SCSI Cables Cables are provided with most Compaq server products that require cabling. If you find that you need an additional cable or that one was not provided with your server product, you can order the necessary cables from your local Compaq Reseller or authorized Compaq Service Provider. -
Page 15: Scsi Cable Connectors
1-6 Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide SCSI Cable Connectors To identify the various SCSI cables required 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter installation in the various configurations of Compaq servers, see Figure 1-2. -
Page 16: Items Needed
Installing the Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter This chapter discusses the installation of the Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter in a Compaq server. WARNING: To reduce the risk of personal injury from electrical shock and hazardous energy levels, only authorized service technicians should attempt to install this equipment. -
Page 17: Preparing The Server
2-2 Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide Preparing the Server Use the following general guidelines to prepare the server for installation of the 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter. WARNING: When working with equipment installed in a rack, be sure that the equipment/rack is stable before beginning. -
Page 18: Cabling The 64-Bit/66 Mhz Single Channel Wide Ultra3 Scsi Adapter
Installing the Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter 2-3 6. Locate the PCI bus expansion slots. Refer to the documentation that came with your server for the specific location of these slots. 7. Depending on your server model, remove the retaining screw or open the expansion slot latches that secure the PCI slots. -
Page 19: Internal Scsi Connections
To connect to a wide Ultra3 SCSI peripheral, use a standard Wide SCSI-Wide SCSI cable. If this cable is not furnished with your Compaq external SCSI device, it can be obtained from your local Compaq Reseller. See “SCSI Cables” in Chapter 1 for information on ordering the correct cables. - Page 20 Installing the Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter 2-5 CAUTION: If your server has an integrated Wide Ultra3 SCSI controller, the controller must be terminated at all times to prevent boot error messages. IMPORTANT: In order to run in LVD mode (Wide Ultra3), all components, including the...
- Page 21 2-6 Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide Replacing the Integrated SCSI Controller Use the following guidelines if you are replacing the integrated SCSI controller with the 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter: 17. Unplug the original SCSI cable from the system board.
-
Page 22: Completing The Installation
Installing the Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter 2-7 3. Route the cable(s) according to the instructions in your server documentation. 4. Attach the cables to the new SCSI devices. Completing the Installation After all cabling and connections have been completed, reassemble the server by following these guidelines: 1. -
Page 23: Installing The Firmware And Software
Chapter Installing the Firmware and Software This chapter outlines driver installation steps to set up the Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter in a server running any of the following operating systems: Microsoft Windows NT 3.51 and 4.0 Microsoft Windows 2000 SCO UnixWare 7.x... -
Page 24: Upgrading The System Rom
3-2 Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide Upgrading the System ROM System ROM can be upgraded by flashing the ROM using a special Compaq utility called System ROMPaq. This utility replaces the existing contents of the ROM with another version stored in a disk file. -
Page 25: Running System Rompaq
Since it is difficult to determine when the firmware needs to be updated, Compaq recommends that you run the latest System ROMPaq on all servers when installing a 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter. -
Page 26: Installing The Drivers
3-4 Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide If you have not yet installed your new 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter, you can do so at this time. See Chapter 2 for general hardware installation and cabling information, then proceed to the next section, “Installing the Drivers.”... -
Page 27: Windows 2000
64-Bit/66-MHz Single Channel Wide Ultra3 SCSI Adapter. 1. Start Windows 2000 on the system and log on to an account with administrative privileges. 2. Insert the Compaq SmartStart and Support Software CD into the CD drive. 3. Click Start, choose Settings, and click Control Panel. -
Page 28: Sco Unixware 7.X
7.xx EFS diskette containing HBA drivers. NOTE: Compaq Extended Feature Supplement (EFS) version 7.xx or later for SCO UnixWare 7.x is required for operation with the Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter. 1. Start the system and log in with root privileges. - Page 29 Installing the Firmware and Software 3-7 Building the EFS Diskettes EFS diskettes can be built either from the Web or from a Compaq SmartStart and Support Software CD. To build the diskettes from the Web, download the latest EFS for SCO OpenServer 5 from the site www.compaq.com/support/files/server/us/index.html...
- Page 30 3-8 Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide 6. Press Tab to highlight the software selections, and use the arrow keys to highlight Compaq Extended Feature Supplement. Press Enter. 7. Press Tab to go back to the menu bar. Choose Software and press Enter.
-
Page 31: Novell Netware 5.1
11. When prompted, enter the IP address, broadcast address, and network mask for each installed network controller. 12. When prompted, insert diskette Volume 2 of the Compaq EFS for SCO OpenServer Release 5 into the drive and press Enter. 13. When installation of the drivers and utilities is complete, the following message is displayed: During this installation, the kernel was relinked. -
Page 32: Ibm Os/2
3-10 Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide 3. Insert the SmartStart and Support Software CD into the CD drive. 4. Copy the following files from the subdirectory \CPQSUPSW\NSSD\NWPA into your NetWare directory: ADPT160.HAM ADPT160.DDI 5. Remove the CD and shutdown the system. - Page 33 Installing the Firmware and Software 3-11 4. Select Compaq OS/2 Support Software - 4.50A Or Later Version and move to the next screen. 5. Chose the option Create Software Diskettes To Floppy Only, then click through the following screens until a screen indicating Please Insert Diskette 4 Of 5…...
-
Page 34: Regulatory Compliance Notices
Appendix Regulatory Compliance Notices Federal Communications Commission Notice Part 15 of the Federal Communications Commission (FCC) Rules and Regulations has established Radio Frequency (RF) emission limits to provide an interference-free radio frequency spectrum. Many electronic devices, including computers, generate RF energy incidental to their intended function and are, therefore, covered by these rules. -
Page 35: Class A Equipment
A-2 Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide Class A Equipment This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. -
Page 36: Declaration Of Conformity For Products Marked With Fcc Logo, United States Only
To identify this product, refer to the Series number found on the product. Modifications The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Compaq Computer Corporation may void the user's authority to operate the equipment. Cables... -
Page 37: Canadian Notice (Avis Canadien
A-4 Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide Canadian Notice (Avis Canadien) Class A Equipment This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. -
Page 38: Japanese Notice
Regulatory Compliance Notices A-5 Japanese Notice Taiwanese Notice... -
Page 39: Electrostatic Discharge
Appendix Electrostatic Discharge To prevent damaging the system, be aware of the precautions you need to follow when setting up the system or handling parts. A discharge of static electricity from a finger or other conductor may damage system boards or other static-sensitive devices. -
Page 40: Grounding Methods
B-2 Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide Grounding Methods There are several methods for grounding. Use one or more of the following methods when handling or installing electrostatic-sensitive parts: Use a wrist strap connected by a ground cord to a grounded workstation or computer chassis. - Page 41 2-2 grounding 2-2 adding a separate SCSI bus 2-5 terminating SCSI cables 1-5, adding internal SCSI devices 2-6 attaching cables 2-4 Compaq authorized reseller ix Compaq System Configuration Utility 2-7 Compaq website ix building diskettes completing installation 2-7...
- Page 42 2 Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide data transfer rates 1-1 help defined additional sources viii Single Channel Wide Ultra3 Compaq website ix SCSI Adapter 1-1 Compq authorized resellers, diskettes telephone numbers ix EFS, for OpenServer 5 3-6...
- Page 43 Index 3 NetWare 5.1 drivers 3-9 SCO OpenServer 5 drivers 3-6 SCO UnixWare 7.x drivers 3-6 SCSI bus adding 2-5 opening the server 2-2 separate 2-5 OpenServer 5 drivers 3-6 SCSI cabling guidelines operating system drivers 3-4 cabling SCSI devices 2-3 operating systems connecting SCSI cables 1-3 UnixWare 7.x 3-6...
- Page 44 4 Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide tagged command queuing 1-2 UnixWare 7.x drivers 3-6 Taiwanese notice A-5 updating technical support viii firmware 2-7 telephone numbers ix system ROM 2-7 terminating, SCSI devices 1-4 text conventions vi...