Download
Share
Print this page
  1. Manuals
  2. Brands
  3. White Knight Manuals
  4. Dryer
  5. BG 43A
  6. Installation and service instructions manual

White Knight BG 43A Installation And Service Instructions Manual

Gas tumble dryer
Hide thumbs Also See for BG 43A:

Advertisement

Quick Links

Download this manual
Gas Tumble dryer BG 43A_
INSTALLATION AND SERVICE INSTRUCTIONS
Keep this booklet for future reference.
The dryer must be fitted by a competent person. In the U.K. CORGI Registered Installers undertake
to work to safe and satisfactory standards.
The dryer must be installed in accordance with the Gas Safety (Installation and Use) Regulations
1998.
Guidance may be obtained from the relevant parts of B.S. 6172: B.S. 5440 parts 1 and 2,
B.S. 7624:2004, B.S. 6891: current editions, I.E.E. Wiring Regulations, and relevant Building
Regulations.
Failure to install the appliance correctly could invalidate the warranty liability claims and could lead to
prosecution.
FOR USE IN GREAT BRITAIN AND EIRE WITH NATURAL GAS ONLY.
GAS CATEGORY I
GAS SUPPLY PRESSURE 20 MBAR.
2H
THE INSTALLER MUST LEAVE THIS BOOKLET WITH THE CUSTOMER

Advertisement

loading
Need help?

Need help?

Do you have a question about the BG 43A and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for White Knight BG 43A

Summary of Contents for White Knight BG 43A

  • Page 1 Gas Tumble dryer BG 43A_ INSTALLATION AND SERVICE INSTRUCTIONS Keep this booklet for future reference. The dryer must be fitted by a competent person. In the U.K. CORGI Registered Installers undertake to work to safe and satisfactory standards. The dryer must be installed in accordance with the Gas Safety (Installation and Use) Regulations 1998.
  • Page 2 Contents Page Technical Data ..... . . Installation ......Service instructions .

  • Page 3: Technical Data

    TECHNICAL DATA CONTROL Type: Pactrol full sequence flame control, P16A GTD(CE) 414601. Ignition electrode gap to burner 3 to 4mm Flame GENERAL failure electrode (4213 078 52641). Height from heater Front loading tumble dryer with gas heating. Reverse action base to centre of electrode 27.0±0.5mm. drum tumble.
  • Page 4 INSTALLATION 1 INSTALLATION 5 POSITION OF DRYER AND CONNECTIONS The dryer is designed for installation using a flexible gas connection with tubing in accordance with B.S. 669. Ensure that the supply gas sizing is adequate. When installing, position the appliance so that the plug is Y = 150 to 330 mm accessible.
  • Page 5 6. OPERATIONAL CHECK PROGRAMME 6.1 Remove the pressure test point screw from the gas Clockwise rotation of the control knob closes switch contacts within the timer to: a) energise the drive motor, tee connection at the back of the dryer and connect a gas pressure gauge.

  • Page 6: Service Instructions

    SERVICE INSTRUCTIONS RECOMMENDATIONS FOR DISMANTLING Note: Re-assembly should be done in reverse sequence to these instructions. Heat Heat HEATER ASSEMBLY REMOVAL Heater Assy. (32), Solenoid Coil (45 or 45A), Flame failure Electrode (33), lgnition Electrode (39). Withdraw the 2-screws securing the Plinth (199) to the Cabinet, unhook the bottom edge fixing, and remove it.
  • Page 7 Withdraw the 3-screws and shakeproof vvashers (13) securing the Flame Tube Assy. (34) to the Cabinet base. Note: On re-assembly the shakeproof washers must be replaced to ensure a good earth connection. Lift out the Heater Assy. To remove either solenoid coil (45 or 45A) disconnect the electrical connectors, unscrew the nut (44) or remove circlip (52) from the top of the valve and lift off.

  • Page 8: Fault Finding

    FAULT FINDING In the event of an electrical fault carry out the preliminary electrical system checks i.e. earth continuity, polarity, and resistance to earth. Use each chart to locate the fault causing the dryer to operate incorrectly as follows: Chart No. 1 Motor does not run.
  • Page 9 Chart 2. Motor runs but full sequence control does not produce ignition spark START With timer ON (30 min) is voltage between output B2 on timer and TB-N 230v? Exchange timer, Does control spark? Does control spark with high heat selected? Does control spark with low heat selected? Disconnect both red wires at timer B2.
  • Page 10 Chart 3. Motor runs Full Sequence Control produces ignition sparks, but gas does not ignite...
  • Page 11 Chart 4. Motor runs, gas ignites but stays on for only short period Before proceeding, ensure polarity of 13 Amp supply socket and earthing is correct. Start Is weight of load suitable? Is filter clean? Is vent hose or terminal unobstructed? Is vent terminal unaffected by wind conditions that may...
  • Page 12 WHITE KNIGHT BG 43A_ CROSSLEE P.L.C. FUNCTIONAL FLOW WIRING DIAGRAM BG 43A_...
  • Page 13 WHITE KNIGHT BG 43A_ CROSSLEE P.L.C. EXPLODED VIEW 1...
  • Page 14 WHITE KNIGHT BG 43A_ CROSSLEE P.L.C. EXPLODED VIEW 2 REAR ASSEMBLY VIEWED FROM FRONT...
  • Page 15 WHITE KNIGHT BG 43A_ CROSSLEE P.L.C. EXPLODED VIEW 3 INTERNALS VIEWED FROM REAR...
  • Page 16 WHITE KNIGHT BG 43A_ CROSSLEE P.L.C. EXPLODED VIEW 4 INTERNALS VIEWED FROM REAR...
  • Page 17 WHITE KNIGHT BG 43A_ CROSSLEE P.L.C. EXPLODED VIEW 5 HEATER ASSEMBLY...
  • Page 18 White Knight BG43A_ Parts List Item Description Part Number Expl. View Control Unit 4213 092 25451 Control Unit Bracket Assembly 4213 070 08623 Screw M4 x 10 821313037161 2,4&5 Rear Seal Assembly 4213 092 08511 External Feed Pipe (Bundy Tube Assy 3)
  • Page 19 White Knight BG43A_ Parts List Cable Clip 4213 078 26231 Door Handle Insert 4213 077 52982 Pan/W Screw St Zn 6 x 7/16 2513 139 03011 1 & 4 No 8 x 1 Fl Head S/Tap Screw MC 8213 130 28241...
  • Page 20 White Knight BG43A_ Parts List Lifter 4213 077 41009 Front Bearing (long) 4213 077 40962 4213 077 40895 Access Cover (fan) 447/1 Access Cover Assembly 4213 092 18081 Fan Spring Clip 4213 075 71162 Fln Tap Scr St Zn 8 x 1/2...

This manual is also suitable for:

43a