Carrier 30GTN Service And Troubleshooting Manual page 37

Table 15 — Configuration Mode and Sub-Mode Directory (cont)
SUB-MODE KEYPAD ENTRY
OPT2
ENTER
RSET
ENTER
SLCT
ENTER
ITEM DISPLAY
CTRL X
CCNA XXX
CCNB XXX
BAUD X
LOAD X LOADING SEQUENCE SELECT
LLCS X LEAD/LAG CIRCUIT SELECT
LCWT XX.X F HIGH LCW ALERT LIMIT
DELY XX MIN MINUTES OFF TIME
CRST X COOLING RESET TYPE
CRT1 XXX.X °F NO COOL RESET TEMP
CRT2 XXX.X °F FULL COOL RESET TEMP
DGRC XX.X F DEGREES COOL RESET
DMDC X DEMAND LIMIT SELECT
DM20 XXX % DEMAND LIMIT AT 20 MA
SHNM XXX LOADSHED GROUP NUMBER
SHDL XXX % LOADSHED DEMAND DELTA
SHTM XXX MIN MAXIMUM LOADSHED TIME
DLS1 XXX % DEMAND LIMIT SWITCH 1
DLS2 XXX % DEMAND LIMIT SWITCH 2
LLEN ENBL/DSBL LEAD/LAG CHILLER ENABLE
MSSL SLVE/MAST MASTER/SLAVE SELECT
SLVA XXX
LLBL ENBL/DSBL LEAD/LAG BALANCE SELECT
LLBD XXX HRS LEAD/LAG BALANCE DELTA
LLDY XX MIN
CLSP X COOLING SETPOINT SELECT
RL.S ENBL/DSBL
CRMP X.X COOLING RAMP LOADING
Z.GN X.X DEADBAND MULTIPLIER
ITEM EXPANSION
CONTROL METHOD
CCN ADDRESS
CCN BUS NUMBER
CCN BAUD RATE
SLAVE ADDRESS
LAG START DELAY
RAMP LOAD SELECT
37
COMMENT
Default: 0
0 = Switch
1 = 7 Day Schedule
2 = Occupancy
3 = CCN Control
Default: 1
Range: 1 to 239
Default: 0
Range: 0 to 239
Default: 3
1 = 2400
2 = 4800
3 = 9600
4 = 19,200
5 = 38,400
Default: 1
1 = Equal
2 = Staged
Default: 1 (size 080-420) 2 (size 040-070)
1 = Automatic
2 = Circuit A Leads
3 = Circuit B Leads
Default: 60
Range: 2 to 60 F
Default: 0 Minutes
Range: 0 to 15 Minutes
0 = No Reset
1 = 4 to 20 mA Input
2 = Outdoor Air Temperature
3 = Return Fluid
4 = Space Temperature
Default: 125 F
Range: 0 to 125 F
Default: 0° F
Range: 0 to 125 F
Default: 0° F
Range: −30 to 30 F
Default: 0
0 = None
1 = Switch
2 = 4 to 20 mA Input
3 = CCN Loadshed
Default: 100%
Range: 0 to 100%
Default: 0
Range: 0 to 99
Default: 0%
Range: 0 to 60%
Default: 60 minutes
Range: 0 to 120 minutes
Default: 80%
Range: 0 to 100%
Default: 50%
Range: 0 to 100%
Default: Disable
Default: Master
Default: 0
Range: 0 to 239
Default: Disable
Default: 168 hours
Range: 40 to 400 Hours
Default: 5 minutes
Range: 0 to 30 minutes
Default: 0
0 = Single
1 = Dual Switch
2 = Dual Clock
3 = 4 to 20 mA Input
Default: Enable
Default: 1.0
Range: 0.2 to 2.0
Default: 1.0
Range: 1.0 to 4.0