Index - Carrier 17 Start Up & Operation Manual

Abbreviations, 4
Accidental Start-Up (To Prevent), 60
Alignment (Open-Drive Machines), 70
Attach to Network Device Control, 43
Automatic Soft Stop Amps Threshold, 46
Auto. Restart After Power Failure, 39
Auxiliary Oil Pump Control (Open-Drive
Machines Only), 36
Calibrate Motor Current Demand Setting, 60
Capacity Override, 36
Carrier Comfort Network Interface, 53
Charge Refrigerant Into Machine, 57
Chilled Water Recycle Mode, 46
Cold Weather Operation, 62
Compressor Bearing and Gear Maintenance, 81
Compressor Fits and Clearances, 102
Condenser, 8
Condenser Freeze Protection, 39
Condenser Pump Control, 39
Contact Seal Maintenance (Open-Drive Machines), 68
Control Algorithms Checkout Procedure, 85
Control Center, 8
Control Center (Inspect), 76
Control Modules, 95
Controls, 12
Controls and Optional Pumpout Compressor, 57
Controls, Definitions, 12
Controls, General, 12
Control Test, 85
Cooler, 8
Coupling Maintenance, 77
Default Screen Freeze, 36
Dehydration, 51
Demand Limit Control, Option, 40
Design Set Points (Input), 55
Display Messages (Checking), 83
Doweling for Open-Drive Machines, 60
Dry Run to Test Start-Up Sequence, 58
Extended Shutdown, 62
Extended Shutdown (After), 62
General Maintenance, 67
Guide Vane Linkage (Checking), 67
Heat Exchanger Tubes (Inspect), 81
High Altitude Locations, 57
High Discharge Temperature Control, 36
Hot Alignment Check for Open-Drive Machines, 60
Ice Build Control, 42
Identification Label, 4
Instruct the Customer Operator, 60
Introduction, 4
Job Data Required, 47
Lead/Lag Control, 40
Leak Rate (Machine), 67
Leak Rate (Refrigerant), 67
Leak Test (Machine), 48
Leak Testing (Refrigerant), 67
LID Operation and Menus, 21
Limited Shutdown (After), 61
Local Occupied Schedule (OCCPC01S) (Input), 55
Local Start-Up, 45
Lubrication Cycle, Hermetic Machines, Details, 10
Lubrication Cycle, Hermetic Machines, Summary, 10
Lubrication Cycle, Open-Drive Machines, Details, 12
Lubrication Cycle, Open-Drive Machines, Summary, 12

INDEX

Lubrication System (Check), 75
Machine Familiarization (17/19EX), 4
Manual Guide Vane Operation, 62
Manual Operation of the Guide Vanes, 58
Module Operation, 95
Motor-Compressor, 8
Motor Cooling Control (Hermetic Motors Only), 36
Motor Maintenance (Open-Drive Motors), 78
Motor/Oil Refrigeration Cooling Cycle, 8
Motor Starter, 8
Oil Changes, 77
Oil Charge, 54
Oil Cooler, 38
Oil Filter (Changing), 76
Oil Pressure and Compressor Stop (Check), 59
Oil Reclaim Filter, 77
Oil Specification, 77
Oil Sump Temperature Control, 38
Open-Drive Motor Auxiliary Devices, 48
Open-Drive Motor Electrical Connection, 47
Open-Drive Motor Handling/Rigging, 81
Open-Drive Motor Pre-Start Checks, 53
Open-Drive Motor Storage, 81
Open Oil Circuit Valves, 48
Operating Condition (Check), 60
Operating Instructions, 61
Operating the Optional Pumpout Compressor, 64
Operator Duties, 61
Optional Pumpout Compressor Water Piping (Check), 52
Options Modules (8-Input), 96
Physical Data (17/19EX), 97
PIC System Components, 14
PIC System Functions, 35
Power Up the Controls and Check the Oil Heater, 54
Pressure Transducers (Check), 82, 84
Processor Module (PSIO), 95
Pumpout and Refrigerant Transfer Procedures, 64
Pumpout and Refrigerant Transfer Procedures,
Preparation, 64
Pumpout System (Check), 57
Pumpout System Maintenance, 82
Ramp Loading Control, 36
Refrigerant (Adding), 67
Refrigerant Filter, 77
Refrigerant Float System (Inspect), 77
Refrigerant Leak Rate, 67
Refrigerant Leak Testing, 67
Refrigerant Properties, 67
Refrigerant (Removing), 67
Refrigerant Tracer, 48
Refrigeration Cycle, 8
Refrigeration Log, 62
Relief Devices (Check), 52
Relief Valves and Piping (Inspect), 77
Remote Start/Stop Controls, 38
Remove Shipping Packaging, 47
Repair the Leak, Retest, and Apply Standing
Vacuum Test, 67
Replacement Chiller Parts (Ordering), 83
Replacing Defective Processor Modules, 96
Return Refrigerant to Normal Operating Conditions, 66
Rotation (Check), 58, 59
Running System (Check), 61
115