Making Pan Adjustments 5.1.4 Making Tilt Adjustments Adjusting Angle of LED Tilt and Width of Illumination Beam 5.2.1 Adjusting the Angle of LED Tilt 5.2.2 Adjusting the Illumination Beam Width Bosch Security Systems, Inc. User Manual F.01U.263.417 | 3.0 | 2012.01...
Page 4
6.5.4 Synchronization submenu 6.5.5 Alarm Output submenu 6.5.6 Connections submenu 6.5.7 Test Signals submenu 6.5.8 Camera ID submenu 6.5.9 Defaults submenu Maintenance Repairs Transfer and Disposal Technical Data Index F.01U.263.417 | 3.0 | 2012.01 User Manual Bosch Security Systems, Inc.
Do not block any ventilation openings. Install in accordance with manufacturer’s instructions. Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat. Bosch Security Systems, Inc. User Manual F.01U.263.417 | 3.0 | 2012.01...
Camera signal - Protect the cable with a primary protector if the camera signal is beyond 140 feet, in accordance with NEC800 (CEC Section 60). F.01U.263.417 | 3.0 | 2012.01 User Manual Bosch Security Systems, Inc.
Page 7
Disconnect the unit's input connectors from outdoor equipment before disconnecting the grounding plug or grounding terminal. – Follow proper safety precautions such as grounding for any outdoor device connected to this unit. Bosch Security Systems, Inc. User Manual F.01U.263.417 | 3.0 | 2012.01...
Page 8
Electronic Surveillance - This device is intended for use in public areas only. U.S. federal law strictly prohibits surreptitious recording of oral communications. Environmental statement - Bosch has a strong commitment towards the environment. This unit has been designed to respect the environment as much as possible.
Network Voltage (TNV) circuits. Video loss - Video loss is inherent to digital video recording; therefore, Bosch Security Systems cannot be held liable for any damage that results from missing video information. To minimize the risk of lost digital information, Bosch Security Systems recommends multiple, redundant recording systems, and a procedure to back up all analog and digital information.
CSA MAKES NO REPRESENTATIONS, WARRANTIES, OR CERTIFICATIONS WHATSOEVER REGARDING THE PERFORMANCE OR RELIABILITY OF ANY SECURITY OR SIGNALING RELATED FUNCTIONS OF THIS PRODUCT. F.01U.263.417 | 3.0 | 2012.01 User Manual Bosch Security Systems, Inc.
Dinion Infrared Imager Safety | en Bosch notices Copyright This manual is the intellectual property of Bosch Security Systems and is protected by copyright. All rights reserved. Trademarks All hardware and software product names used in this document are likely to be registered trademarks and must be treated accordingly.
Verify that all the parts listed in the Parts List below are included. If any items are missing, notify your Bosch Security Systems Sales or Customer Service Representative. The original packing carton is the safest container in which to transport the unit and must be used if returning the unit for service.
Solid wire (AWG 16 to 26) Metal conduit (for protection of power cables and input/output cables) Mounting hardware (such as a corner mount adapter or pole mount adapter, available separately from Bosch) 2.1.3 Required Tools (User-Supplied) Quantity Item 2.5 mm (0.1 in.) straight-blade screwdriver Socket wrench 14 mm (9/16 in.) socket...
Verify that all the parts listed in the Parts List below are included. If any items are missing, notify your Bosch Security Systems Sales or Customer Service Representative. The original packing carton is the safest container in which to transport the unit and must be used if returning the unit for service.
Page 15
Recommended mounting height is at least 4 m (13 ft); however, optimal conditions will vary with the specific installation environment. Bosch Security Systems, Inc. User Manual F.01U.263.417 | 3.0 | 2012.01...
Power and I/O cabling must be routed separately inside different permanently earthed metal conduits. Route all rough wiring including: power, control, video coax, alarms I/O, and relay I/O. See for video and control protocol methods. F.01U.263.417 | 3.0 | 2012.01 User Manual Bosch Security Systems, Inc.
Page 17
CAUTION! Select a rigid mounting location to prevent excessive vibration to the camera. Bosch Security Systems, Inc. User Manual F.01U.263.417 | 3.0 | 2012.01...
See Section 4.3 Route Wires and Attach Connectors, page 20. Attach pendant arm to junction box. See Section 4.4 Attach Pendant Arm to Junction Box, page 23. F.01U.263.417 | 3.0 | 2012.01 User Manual Bosch Security Systems, Inc.
Mark the points on the wall in the center of the holes where the mounting bolts will be positioned. Remove the wall mount bracket and drill pilot holes at each marked point. Bosch Security Systems, Inc. User Manual F.01U.263.417 | 3.0 | 2012.01...
(about 5 mm (0.2 in.) of insulation). See Figure 4.3, Page 23, above, for the connector locations. Loosen the screws of the supplied 2-pole connector (2-pin Power Plug) and attach the incoming power wires. F.01U.263.417 | 3.0 | 2012.01 User Manual Bosch Security Systems, Inc.
Coaxial cable terminated with BNC connectors is the most common method for transmitting composite video. Bilinx control data can also be sent over the same cable. Bilinx is a Bosch 2-way communication protocol for analog cameras that allows remote control, configuration, and updates over a video coax cable.
Pin 1 of CN10 7 D2 Illuminator on alarm output connection 2 Orange Pin 2 of CN10 Voltage free and either NO (Illuminator off mode) or NC (Illuminator on mode). F.01U.263.417 | 3.0 | 2012.01 User Manual Bosch Security Systems, Inc.
Serious injury or death can occur if the hinge pins of the camera arm are not fully engaged (locked) to the junction box. Use caution before releasing the camera arm. Bosch Security Systems, Inc. User Manual F.01U.263.417 | 3.0 | 2012.01...
Unscrew the four (4) captive screws (item 1 in the figure below) of the access panel on the rear of the camera housing. Figure 5.1 Rear camera housing with access panel F.01U.263.417 | 3.0 | 2012.01 User Manual Bosch Security Systems, Inc.
(tele or wide): – Turn the set screw to the left for a wider field of view. – Turn the set screw to the right for a telephoto field of view. Bosch Security Systems, Inc. User Manual F.01U.263.417 | 3.0 | 2012.01...
Replace the round caps when you finish the adjustments. Figure 5.4 Example orientation: Camera rotated 90 degrees left, pointing up 44 degrees. From left: front view, side view, back view F.01U.263.417 | 3.0 | 2012.01 User Manual Bosch Security Systems, Inc.
Use the 31 mm screw for general area surveillance / targets closer to the camera. Use the 25 mm screw for other use cases such as monitoring a perimeter. Bosch Security Systems, Inc. User Manual F.01U.263.417 | 3.0 | 2012.01...
Without the 3D diffuser, a focal length of 27 mm (or greater) provides a horizontal field of view (FOV) of 10° (or less) to match the illumination pattern; the resulting beam angle is 10° (H) x 10° (V). F.01U.263.417 | 3.0 | 2012.01 User Manual Bosch Security Systems, Inc.
Page 29
Remove the 3D diffuser and plate assembly as when installing the 3D diffuser. Remove the 3D diffuser from the diffuser plate. Install the diffuser plate into the camera housing to secure and seal the unit. Bosch Security Systems, Inc. User Manual F.01U.263.417 | 3.0 | 2012.01...
(center) for longer than 2 seconds. 6.1.2 Menu navigation Five keys, located behind the access panel on the back of the camera, are used for navigating through the menu system. F.01U.263.417 | 3.0 | 2012.01 User Manual Bosch Security Systems, Inc.
Install/Mode submenu. The modes are defined as follows: 24-hour Default installation mode to provide stable pictures over a 24-hour period. These settings are optimized for out-of- the-box installation. Bosch Security Systems, Inc. User Manual F.01U.263.417 | 3.0 | 2012.01...
Bilinx communications can only be disabled using the buttons on the camera. Disabled camera buttons When the Bilinx communications link is active, the buttons on the camera are disabled. F.01U.263.417 | 3.0 | 2012.01 User Manual Bosch Security Systems, Inc.
Copy active mode Available mode Copies current mode settings to the numbers mode number selected. Default mode Submenu Restores camera to the factory default settings. EXIT Returns to main menu. Bosch Security Systems, Inc. User Manual F.01U.263.417 | 3.0 | 2012.01...
DVR or IP encoder to compensate for compression methods. Off - The camera output is optimized for connection to an analog system (matrix switcher or monitor). EXIT Returns to main menu. F.01U.263.417 | 3.0 | 2012.01 User Manual Bosch Security Systems, Inc.
Selects the gain setting for Fixed gain operation (0 is no gain). Actual AGC Displays the actual AGC value from the camera to help compare gain level with lighting levels and picture performance. Bosch Security Systems, Inc. User Manual F.01U.263.417 | 3.0 | 2012.01...
Page 36
When active, some noise or spots may appear in the picture. This is normal camera behavior. It may also cause motion blur on moving objects. EXIT Returns to main menu. F.01U.263.417 | 3.0 | 2012.01 User Manual Bosch Security Systems, Inc.
Motion - the camera avoids motion blur as long as the light level permits (it switches to monochrome earlier than it would with Color priority). Bosch Security Systems, Inc. User Manual F.01U.263.417 | 3.0 | 2012.01...
Auto - the camera switches the illuminator on and off depending on the Day/Night mode. Intensity 0 to 30 Adjusts the intensity of the illuminator light. The default value is 30. EXIT Returns to main menu. F.01U.263.417 | 3.0 | 2012.01 User Manual Bosch Security Systems, Inc.
A low (negative) value makes the picture less sharp. Increasing sharpness brings out more detail. Extra sharpness can enhance the details of license plates, facial features and the edges of certain surfaces. Bosch Security Systems, Inc. User Manual F.01U.263.417 | 3.0 | 2012.01...
ATW and AWBhold - adjusts the B gain to -50 to +50 optimize the white point. Manual - adjusts the Blue gain. Green gain -50 to +50 Manual - adjusts the Green gain. F.01U.263.417 | 3.0 | 2012.01 User Manual Bosch Security Systems, Inc.
Press Select again to freeze the area and exit the menu. Note: There is one programmable VMD area. When VMD is enabled, normal light fluctuations or environmental factors can contribute to false-positive alarms. Because of this, it is Bosch Security Systems, Inc. User Manual F.01U.263.417 | 3.0 | 2012.01...
Set LVL Only for video-iris lenses. Adjust the level control on the lens to center the level detector indicator (see below). EXIT Returns to Install menu. F.01U.263.417 | 3.0 | 2012.01 User Manual Bosch Security Systems, Inc.
Press Select again to freeze the area and exit the menu. Note: There are four programmable areas for privacy masking. Bosch Security Systems, Inc. User Manual F.01U.263.417 | 3.0 | 2012.01...
Filter toggle - output relay closes just before the IR filter starts moving and opens when video level has stabilized (2 to 3 seconds). EXIT Returns to Install menu. F.01U.263.417 | 3.0 | 2012.01 User Manual Bosch Security Systems, Inc.
Color bars Select the desired test pattern to help 100%, installation and fault-finding. Grayscale 11- step, Sawtooth 2H, Checker board, Cross hatch, UV plane EXIT Returns to Install menu. Bosch Security Systems, Inc. User Manual F.01U.263.417 | 3.0 | 2012.01...
Restores all settings of the six modes to their default (factory) values. Select YES, then press the Menu/ Select button to restore all values. When completed, the message RESTORED! appears. EXIT Returns to Install menu. F.01U.263.417 | 3.0 | 2012.01 User Manual Bosch Security Systems, Inc.
Defective or superfluous devices and parts should be disposed of professionally or taken to your local collection point for hazardous materials. Bosch Security Systems, Inc. User Manual F.01U.263.417 | 3.0 | 2012.01...
(15.8 in. x 7.6 in. x 16.2 in.) Weight, 6.6 kg (14.55 lbs) Camera and Bracket Weight, Junction Box 1.4 kg (3.5 lbs) Construction Corrosion-resistant aluminum Color White (RAL 9010) with black (RAL 9005) detail F.01U.263.417 | 3.0 | 2012.01 User Manual Bosch Security Systems, Inc.
Page 49
Operating Humidity 20% to 100% (condensing) Storage Humidity up to 100% Wind load, operational 145 kph (90 mph) (sustained) Wind load, non-operational Gusts up to 260 kph (155 mph) Bosch Security Systems, Inc. User Manual F.01U.263.417 | 3.0 | 2012.01...
13 pendant arm attaching to power supply box polarity 21 power supply box attaching to pendant arm 23 Pre-Comp 21 wiring for pendant arm, corner or mast mount 16 F.01U.263.417 | 3.0 | 2012.01 User Manual Bosch Security Systems, Inc.
Page 51
Dinion Infrared Imager Index | en Bosch Security Systems, Inc. User Manual F.01U.263.417 | 3.0 | 2012.01...
Page 52
| Index Dinion Infrared Imager F.01U.263.417 | 3.0 | 2012.01 User Manual Bosch Security Systems, Inc.
Page 53
Dinion Infrared Imager Index | en Bosch Security Systems, Inc. User Manual F.01U.263.417 | 3.0 | 2012.01...
Page 54
| Index Dinion Infrared Imager F.01U.263.417 | 3.0 | 2012.01 User Manual Bosch Security Systems, Inc.