Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Specialized FSR
Summary of Contents for Specialized FSR
-
Page 3: Table Of Contents
DOWN TUBE CABLE GUIDE INSTALLATION ......9 FRAME SCHEMATIC .............10 FRAME PIVOT SPECIFICATIONS ...........11 SETUP DATA ................12 Please note all instructions are subject to change for improvement without notice. Please visit www.specialized.com for periodic tech updates. Feedback: techdocs@specialized.com OM0378 - Rev. A, August 2011... -
Page 4: Introduction
Frames or parts under high stress may fail, causing you to lose control or fall. Because of the risk involved, Specialized recommends that you conduct a thorough inspection before each ride. If you miss a jump, ditch your bike in mid crash, dump or launch your bike without you on it, inspect yourself for injury, then carefully inspect your bicycle for damage. -
Page 5: Service And Modifications
Your bicycle has been engineered and tested with specific components and parts. Because of the great variety in these items, it is impossible for Specialized to test and approve of all possible combinations. Modifying the frame, fork, or any of the components may make your bike unsafe. -
Page 6: Fork Setup Information
FORK SETUP INFORMATION WARNING! Status frames are compatible ONLY with forks that have travel of 8” (200mm) or less. Use of different styled forks or forks with longer travel may result in catastrophic failure of the frame which may result in serious personal injury or death. -
Page 7: Frame Features
-Link @ Frame Pivot 12. Replaceable Derailleur Hanger FRAME LINKAGE ASSEMBLY Specialized recommends following a specific order when assembling the rear triangle pivot locations of FSR suspension bike models (see illustration above). 1. Main pivot (#5) 2. Main link pivot (#8) 3. -
Page 8: Frame Geometry
FRAME GEOMETRY 1. Top Tube Length 4. Seat Tube Angle 7. Standover Height 10. Reach 2. Chainstay Length 5. Head Tube Angle 8. Head Tube Length 3. BB Height 6. Wheelbase 9. Stack TT length is the Horizontal Measurement from the center-line of the HT at the top of the HT to the center-line of the projected seat tube. -
Page 9: Status
STATUS SMALL MEDIUM LARGE 21.97” 22.95” 23.94” 16.77” 16.77” 16.77” 13.98” 13.98” 13.98” 75° 75° 75° 64.5° 64.5° 64.5° 1164 45.83” 1189 46.81” 1214 47.80” 29.37” 29.25” 29.88” 4.72” 4.72” 4.72” 25.43” 25.43” 25.43” 16.54” 16.73” 17.72”... -
Page 10: Shock Setup
SHOCK SETUP SETTING SAG Status Sag (%/mm): 30-35% / 21-24mm Proper sag should be achieved with one turn of preload on the spring. More then two turns of preload will require a higher spring rate or not enough sag will require a softer spring rate. See spring rate chart below for additional information or refer to the shock manual. -
Page 11: Derailleur Guard
DERAILLEUR GUARD The Specialized Derailleur guard is available separately through your Specialized Authorized Dealer. The guard works with solid or Q/R axle types and is compatible with all Mountain bike models using the Rev2 Alloy Mtn Derailleur Hanger. Guard Part#... -
Page 12: Frame Schematic
FRAME SCHEMATIC NOTE - Bearing and Bolt Kits are available only through your Specialized Authorized Dealer. To retain your warranty and for your safety, all maintenance should be performed by your Specialized Authorized Dealer. -
Page 13: Frame Pivot Specifications
FRAME PIVOT SPECIFICATIONS NOTE: All pivot bolt threads require blue threadlocker. -
Page 14: Setup Data
SETUP DATA DATE RIDER WEIGHT FORK SPRING RATE FORK REBOUND DAMPING (# of clicks from full slow) FORK COMPRESSION DAMPING (# of clicks from full firm) SHOCK SPRING RATE SHOCK REBOUND DAMPING (# of clicks from full slow) SHOCK COMPRESSION DAMPING (# of clicks from full firm) - Page 16 SPECIALIZED BICYCLE COMPONENTS 15130 Concord Circle, Morgan Hill, CA 95037 (408) 779-6229 www.specialized.com...
Need help?
Do you have a question about the FSR and is the answer not in the manual?
Questions and answers