Summary of Contents for Vogelzang International BX26E
Page 1
STANDARD BOXWOOD STOVE Model BX26E Owners Manual (Save These Instructions) READ ALL INSTRUCTIONS CAREFULLY This stove is not a UL Listed stove. BEFORE INSTALLING OR OPERATING THIS STOVE. FAILURE TO FOLLOW INSTRUC- NOTE: IT IS RECOMMENDED INSTALLATION TIONS MAY RESULT IN PROPERTY DAMAGE, BE COMPLETED BY A QUALIFIED HEATING BODILY INJURY, OR EVEN DEATH.
TO AN ALUMINUM TYPE B GAS VENT. This is and odor may be emitted from the light oils used in not safe. Use approved masonry or an Underwrit- construction of the fire box. This should disappear Page 2 / BX26E-STD VGZ-006 / 20120225.0...
Page 3
1978. The address of the NFPA is Batterymarch TION WITH ANY AIR DISTRIBUTION DUCT Park, Quincy, MA 02269. WORK UNLESS SPECIFICALLY APPROVED FOR SUCH INSTALLATIONS. 30. A WOOD-BURNING STOVE MUST NEVER BE INSTALLED IN A HALLWAY OR NEAR A STAIR- VGZ-006 / 20120225.0 BX26E-STD / Page 3...
Parts – Standard Boxwood ................16 Floor Protector Calculations ................17 NOTE: A PROFESSIONAL, LICENSED HEAT- ING AND COOLING CONTRACTOR MUST BE CONSULTED IF YOU HAVE QUESTIONS REGARDING THE INSTALLATION OF THIS SOLID FUEL BURNING APPLIANCE. Page 4 / BX26E-STD VGZ-006 / 20120225.0...
(B), flat washers (E) hearth. Hold in position with round head stove and hex nuts (F). bolt (C) and large flat washer (D). ill. B – Rear Leg Assembly continued on next page VGZ-006 / 20120225.0 BX26E-STD / Page 5...
(figure 1–3), locate your floor protector accordingly and carefully place the stove in your selected location. Install connector pipe, elbows, and thimble as required, utilizing either a continued on next page Page 6 / BX26E-STD VGZ-006 / 20120225.0...
Unit Corner to Wall ........ 36 inches Minimum Corner Clearances from Pipe Connector to Backwall....38 inches Combustible Surfaces Pipe Connector to Ceiling ..... 18 inches CAUTION: KEEP FURNISHINGS AND OTHER COMBUSTIBLE MATERIALS AWAY FROM THE STOVE. VGZ-006 / 20120225.0 BX26E-STD / Page 7...
NECTOR PIPE AS A CHIMNEY - A HOUSE FIRE towards the stove. This will allow any condensation COULD RESULT. in the flue to run back into the firebox. CORRECT WRONG WRONG Figure 4 – Stovepipe/Flue Connections Page 8 / BX26E-STD VGZ-006 / 20120225.0...
5. C o n t a c t y o u r l o c a l b u i l d i n g a u t h o r i t y for approved methods of installation and any necessary permits and/or inspections. Figure 6 - Chimney Construction through Attic Space VGZ-006 / 20120225.0 BX26E-STD / Page 9...
Page 10
Chimney Sweep, or a knowledgeable inspector. Consult your insurance company if you cannot find a qualified expert. Figure 8 - Chimney Connection to Firebox continued on next page Through Masonry Wall Page 10 / BX26E-STD VGZ-006 / 20120225.0...
8˝/203mm of liner must remain below the entry position. When locating the stove and stovepipe, all Battery March Park, Quincy, MA 02269. minimum clearances must be observed from com- bustible surfaces including mantels, combustible Figure 9 - Fireplace Conversion VGZ-006 / 20120225.0 BX26E-STD / Page 11...
ESPECIALLY GASOLINE, OUT OF THE the faster and hotter the fire will burn. Do not over VICINITY OF THE STOVE — WHETHER IN USE fire the stove. OR IN STORAGE. continued on next page VGZ-006 / 20120225.0 BX26E-STD / Page 13...
FIRE. TOO MUCH WOOD OR BURNING NON- ashes on top of the fire. RECOMMENDED MATERIALS SUCH AS TRASH OR FLAMMABLE LIQUIDS MAY CAUSE OVER FIRING. continued on next page Page 14 / BX26E-STD VGZ-006 / 20120225.0...
(3) CALL THE FIRE DEPARTMENT. ing and/or replacing the cement/joint mortar along the seams where the cast iron components meet. IF A CHIMNEY FIRE HAS OCCURRED, HAVE YOUR CHIMNEY INSPECTED BY A QUALIFIED EXPERT BEFORE USING AGAIN. VGZ-006 / 20120225.0 BX26E-STD / Page 15...
ORDERING PARTS - BX26E BOXWOOD STOVE When ordering missing or replacement parts, always give the Model Number of the stove, Part Number, and Part Description. Use the illustration and parts list provided to identify parts. Part No. Description Qty. Leg ............... 4 Bottom ............
Rbrick + Rmin.brd = 0.80 + 0.431 = 1.231 = Rsystem Step 4: Compare Rsystem to Rspecs Rsystem = 1.231 is larger than Rspecs of 0.893. System R-value exceeds the required specifications and therefore is an acceptable alternative. VGZ-006 / 20120225.0 BX26E-STD / Page 17...
Page 18
“FOR GOD SO LOVED THE WORLD THAT HE GAVE HIS ONLY BEGOTTEN SON, THAT WHOEVER BELIEVES IN HIM SHALL NOT PERISH BUT HAVE ETERNAL LIFE” JOHN 3:16 MADE IN CHINA Vogelzang International Corporation 400 West 17th Street Holland, Michigan 49423 www.vogelzang.com Phone: 1-616-396-1911 Fax: 1-616-396-1971 Page 18 / BX26E-STD VGZ-006 / 20120225.0...
Need help?
Do you have a question about the BX26E and is the answer not in the manual?
Questions and answers