Lennox Hearth Products Rhapsody RHAP42N Installation Instructions Manual

Lennox Hearth Products Rhapsody RHAP42N Installation Instructions Manual

Linear direct-vent gas fireplace
Hide thumbs Also See for Rhapsody RHAP42N:
Table of Contents

Advertisement

P/N 506023-14 Rev. C 09/2012
This manual is one of a set of two supporting this product.
Refer to P/N 506025-06 for Care and Operation Instructions.
Ce manuel est disponible en francais, simplement
en faire la demande. Numéro de la pièce 506223-34.
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
INSTALLATEUR : Laissez cette notice avec l'appareil.
CONSOMMATEUR : Conservez cette notice pour
consultation ultérieure.
This appliance may be installed in an aftermarket permanently located, manufactured home (USA only) or mobile
home, where not prohibited by local codes.
This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for
use with other gases, unless a certified kit is used.
WARNING / AVERTISSEMENT / AVISO
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
WARNING: If the information in these instructions
is not followed exactly, a fire or explosion may
result, causing property damage, personal injury,
or death.
- Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any other
appliance.
- WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any
phone in your building.
• Immediately call your gas supplier from a
neighbor's phone. Follow the gas supplier's
instructions.
• If you cannot reach your gas supplier, call the fire
department.
- Installation and service must be performed by a
qualified installer, service agency or the gas supplier.
INSTALLATION INSTRUC TIONS
Rhapsody
Direct-Vent Gas Fireplace
MODELS
Intertek Report No.
100404899PRT-001
Please read and understand these instructions
before starting installation.
UNE SURFACE VITRÉE CHAUDE
PEUT CAUSER DES BRÛLURES.
LAISSER REFROIDIR LA SURFACE
VITRÉE AVANT D'Y TOUCHER.
NE PERMETTEZ JAMAIS À UN ENFANT
DE TOUCHER LA SURFACE VITRÉE.
AVERTISSEMENT : Assurez-vous de bien suivre les
instructions données dans cette notice pour réduire au
minimum le risque d'incindie ou d'explosion ou pour
éviter tout dommage matériel, toute blessure ou la mort.
- Ne pas entreposer ni utilizer d'essence ni d'autres vapeurs
ou liquides inflammables dans le voisinage de cet appareil
ou de tout autre appareil.
- QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ :
• Ne pas tenter d'allumer d'appareil.
• Ne touchez à aucan interrupteur. Ne pas vous servir des
téléphones se trouvant dans le bâtiment où vous trouvez.
• Appelez immédiatement votre fournisseur de gaz depuis
un voisin. Suivez les instructions du fournisseur.
• Si vous ne pouvez rejoindre le fournisseur de gaz,
appelez le service des incindies.
- L'installation et l'entretien doivent être assurés par un
installateur ou un service d'entretien qualifié ou par le
fournisseur de gaz.
Linear
RHAP42N
RHAP54N
Look for the EnerGuide
Gas Fireplace Energy
Efficiency Rating in this manual.
Based on CSA P.4.1-02
EL VIDRIO CALIENTE
CAUSARÁ QUEMADURAS.
USTED DEBE NUNCA
TOCAR EL VIDRIO CALIENTE.
LOS NIÑOS DEBEN NUNCA
TOCAR EL VIDRIO.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Rhapsody RHAP42N and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Lennox Hearth Products Rhapsody RHAP42N

  • Page 1 Rhapsody Linear ™ Direct-Vent Gas Fireplace MODELS RHAP42N RHAP54N P/N 506023-14 Rev. C 09/2012 This manual is one of a set of two supporting this product. Refer to P/N 506025-06 for Care and Operation Instructions. Ce manuel est disponible en francais, simplement en faire la demande.
  • Page 2: Table Of Contents

    LENNOX HEARTH PRODUCTS • RHAPSODY™ LINEAR DIRECT-VENT GAS FIREPLACES (MODELS RHAP42N & RHAP54N) • INSTALLATION INSTRUCTIONS Firestop/Spacer Requirements TABLE Of PACkAgINg (Vertical and Horizontal) ... . 13 Vent Section Lengths (Nominal/Net) ..14 CONTENTS Telescopic Vent Section .
  • Page 3: Important Warnings/Notices

    LENNOX HEARTH PRODUCTS • RHAPSODY™ LINEAR DIRECT-VENT GAS FIREPLACES (MODELS RHAP42N & RHAP54N) • INSTALLATION INSTRUCTIONS IMPORTANT WARNINg WARNINg WARNINgS/NOTICES young children should be care- Any safety screen or guard fully supervised when they are removed for servicing the appli-...
  • Page 4: General Information

    LENNOX HEARTH PRODUCTS • RHAPSODY™ LINEAR DIRECT-VENT GAS FIREPLACES (MODELS RHAP42N & RHAP54N) • INSTALLATION INSTRUCTIONS LISTINg INfORMATION REqUIREMENTS fOR COMMON- gENERAL WEALTH Of MASSACHUSETTS These appliances comply with National Safety INfORMATION Standards and are tested and listed by Intertek These fireplaces are approved for installation in (Report No.
  • Page 5: Typical Installation Sequence/Checklist

    LENNOX HEARTH PRODUCTS • RHAPSODY™ LINEAR DIRECT-VENT GAS FIREPLACES (MODELS RHAP42N & RHAP54N) • INSTALLATION INSTRUCTIONS  8. field wiring. TyPICAL INSTALLATION PRE-INSTALLATION  Route fireplace wiring ..24 SEqUENCE/CHECkLIST STEPS ...
  • Page 6: Clearances

    LENNOX HEARTH PRODUCTS • RHAPSODY™ LINEAR DIRECT-VENT GAS FIREPLACES (MODELS RHAP42N & RHAP54N) • INSTALLATION INSTRUCTIONS MANTELS CLEARANCES Non-Combustible Mantels Do NOT insulate space Mantels constructed of non-combustible between appliance and Do NOT insulate space area above it. material may be installed at any height above...
  • Page 7: Location And Framing

    LENNOX HEARTH PRODUCTS • RHAPSODY™ LINEAR DIRECT-VENT GAS FIREPLACES (MODELS RHAP42N & RHAP54N) • INSTALLATION INSTRUCTIONS fRAMINg THE fIREPLACE LOCATION ANd TyPICAL LOCATIONS/INSTALLATION 1. Assemble the top spacers (Figure 4). fRAMINg Note: When unit is installed with one side 2. Adjust the nailing flanges, as applicable flush with a wall, the wall on the other (see Page 9).
  • Page 8: Fireplace Dimensions

    LENNOX HEARTH PRODUCTS • RHAPSODY™ LINEAR DIRECT-VENT GAS FIREPLACES (MODELS RHAP42N & RHAP54N) • INSTALLATION INSTRUCTIONS LOCATION ANd fRAMINg (CONTINUEd) fIREPLACE dIMENSIONS TOP VIEW fireplace dimensions Viewable glass Size Unit Model RHAP42N 40" Wide x 10-1/2" High 26-7/8 53-3/4 32-1/2 RHAP54N 51"...
  • Page 9: Unit Nailing Flanges

    LENNOX HEARTH PRODUCTS • RHAPSODY™ LINEAR DIRECT-VENT GAS FIREPLACES (MODELS RHAP42N & RHAP54N) • INSTALLATION INSTRUCTIONS ROOf OPENINg fRAMINg LOCATION ANd fRAMINg SECURINg UNIT TO fRAMINg (CONTINUEd) [Vertical Termination] By NAILINg fLANgES UNIT NAILINg fLANgES Identify the location for the vent at the roof.
  • Page 10: Gas Requirements And Connection

    LENNOX HEARTH PRODUCTS • RHAPSODY™ LINEAR DIRECT-VENT GAS FIREPLACES (MODELS RHAP42N & RHAP54N) • INSTALLATION INSTRUCTIONS INPUT RATES gAS REqUIREMENTS The appliance and its appliance main gas valve must be disconnected from the gas INPUT RATES (BTU/hr) ANd CONNECTION supply piping system during any pressure...
  • Page 11: Burner Orifice Sizes

    LENNOX HEARTH PRODUCTS • RHAPSODY™ LINEAR DIRECT-VENT GAS FIREPLACES (MODELS RHAP42N & RHAP54N) • INSTALLATION INSTRUCTIONS gAS fLEx-LINE gAS-LINE SHUTOff VALVE gAS REqUIREMENTS/CONNECTION The gas-line shutoff valve provided with the The flexible gas-line connector (“flex-line”) (CONTINUEd) fireplace has a 1/2" NPT thread inlet port.
  • Page 12: Routing The Gas-Line

    LENNOX HEARTH PRODUCTS • RHAPSODY™ LINEAR DIRECT-VENT GAS FIREPLACES (MODELS RHAP42N & RHAP54N) • INSTALLATION INSTRUCTIONS CONNECTINg TO THE gAS SUPPLy TESTINg CONNECTIONS gAS REqUIREMENTS/CONNECTION (fACTORy ANd fIELd) (CONTINUEd) IMPORTANT: Do NOT connect the fOR gAS LEAkS fireplace to the gas supply line until ROUTINg THE gAS-LINE fireplace installation is complete.
  • Page 13: Venting Installation

    LENNOX HEARTH PRODUCTS • RHAPSODY™ LINEAR DIRECT-VENT GAS FIREPLACES (MODELS RHAP42N & RHAP54N) • INSTALLATION INSTRUCTIONS APPROVEd VENT COMPONENTS fIRESTOP/SPACER VENTINg REqUIREMENTS These appliances are designed, tested, and INSTALLATION listed for installation and operation with the Vertical firestop/Spacer must be...
  • Page 14: Vent Section Lengths (Nominal/Net)

    LENNOX HEARTH PRODUCTS • RHAPSODY™ LINEAR DIRECT-VENT GAS FIREPLACES (MODELS RHAP42N & RHAP54N) • INSTALLATION INSTRUCTIONS i t c VENTINg INSTALLATION VENT SECTION LENgTHS VENT SECTION LENgTHS i t c (CONTINUEd) i t c i t c O O O O O...
  • Page 15: Vent Run Support Requirements

    LENNOX HEARTH PRODUCTS • RHAPSODY™ LINEAR DIRECT-VENT GAS FIREPLACES (MODELS RHAP42N & RHAP54N) • INSTALLATION INSTRUCTIONS Supporting Horizontal Vent Runs VENTINg INSTALLATION NOTICE: It is important to install See Figure 22. Install support straps every (CONTINUEd) horizontal runs on a steady, (i.e., no 5 ft (1.524 m) along horizontal/inclined...
  • Page 16: Vent Restrictor Requirements

    LENNOX HEARTH PRODUCTS • RHAPSODY™ LINEAR DIRECT-VENT GAS FIREPLACES (MODELS RHAP42N & RHAP54N) • INSTALLATION INSTRUCTIONS VENTINg INSTALLATION Vent Restrictor Assembly Settings and Applications (CONTINUEd) Setting 1 (Vent Restrictor Base only) is required for the following configurations: VENT RESTRICTOR • Horizontal termination with total vertical run of more than 6 ft.
  • Page 17: Using Secure Flex ® Kits/Components

    LENNOX HEARTH PRODUCTS • RHAPSODY™ LINEAR DIRECT-VENT GAS FIREPLACES (MODELS RHAP42N & RHAP54N) • INSTALLATION INSTRUCTIONS VENTINg INSTALLATION flex Vent Note: Outer Pipe Is Pulled Away To (CONTINUEd) Show The detail of The Inner Pipe Securing Screw - 3 Places...
  • Page 18: Vertical Termination Systems

    LENNOX HEARTH PRODUCTS • RHAPSODY™ LINEAR DIRECT-VENT GAS FIREPLACES (MODELS RHAP42N & RHAP54N) • INSTALLATION INSTRUCTIONS VERTICAL TERMINATION VERTICAL Vertical Termination SySTEM RISE-TO-RUN RATIOS TERMINATION SySTEMS flashing and Max. Total H Min. Total V Storm Collar feet (meters) feet (meters) TyPICAL VERTICAL (1.524)
  • Page 19: Vertical Vent Termination Clearances

    LENNOX HEARTH PRODUCTS • RHAPSODY™ LINEAR DIRECT-VENT GAS FIREPLACES (MODELS RHAP42N & RHAP54N) • INSTALLATION INSTRUCTIONS TERMINATION HEIGHTS FOR VENTS ABOVE VERTICAL TERMINATION SySTEMS FLAT OR SLOPED ROOFS Vent/air Intake Termination Clearances Horizontal Overhang (CONTINUEd) Above the High Side of an Angled Roof (Ref.
  • Page 20: Horizontal Termination Systems: Typical Horizontal Termination Systems

    LENNOX HEARTH PRODUCTS • RHAPSODY™ LINEAR DIRECT-VENT GAS FIREPLACES (MODELS RHAP42N & RHAP54N) • INSTALLATION INSTRUCTIONS HORIZONTAL  TERMINATION SySTEMS TyPICAL HORIZONTAL  TERMINATION SySTEMS Horizontal Termination Note: Building codes limit or prohibit horizontal termination Vertical firestop/  in specific areas. for location...
  • Page 21: Horizontal Vent Termination Clearances

    LENNOX HEARTH PRODUCTS • RHAPSODY™ LINEAR DIRECT-VENT GAS FIREPLACES (MODELS RHAP42N & RHAP54N) • INSTALLATION INSTRUCTIONS Horizontal Vent Termination Clearances HORIZONTAL TERMINATION SySTEMS (CONTINUEd) Combustible Projection 2-1/2 inches or less in length All horizontal terminations may be located as close as...
  • Page 22: Exterior Horizontal Vent Termination Clearance Requirements (Ansi/Csa)

    LENNOX HEARTH PRODUCTS • RHAPSODY™ LINEAR DIRECT-VENT GAS FIREPLACES (MODELS RHAP42N & RHAP54N) • INSTALLATION INSTRUCTIONS HORIZONTAL TERMINATION SySTEMS (CONTINUEd) NOTE: Local Codes Or Regulations May Require Different Clearances. See Item D in the Text Below. NOTE: Location Of The Vent Termination...
  • Page 23: Installing Horizontal Vent Termination

    LENNOX HEARTH PRODUCTS • RHAPSODY™ LINEAR DIRECT-VENT GAS FIREPLACES (MODELS RHAP42N & RHAP54N) • INSTALLATION INSTRUCTIONS HORIZONTAL TERMINATION SySTEMS To help minimize water infiltration it Firestop/Spacer (SV4.5HF) shown Typical is recommended that the firestop/ (CONTINUEd) Termination on the exterior side of the wall. It Shown Spacer (SV4.5Hf) be installed on...
  • Page 24: Field Wiring

    LENNOX HEARTH PRODUCTS • RHAPSODY™ LINEAR DIRECT-VENT GAS FIREPLACES (MODELS RHAP42N & RHAP54N) • INSTALLATION INSTRUCTIONS 0.375" 0.25" Ø fIELd WIRINg WARNINg 0.375" Electrical grounding Instructions WARNING: NOT FOR USE WITH SOLID FUEL This appliance is equipped with a three-prong (grounding) plug for your CAUTION: Label all wires prior to discon- Do not connect 120 V AC to the control valve.
  • Page 25: Route Fireplace Wiring

    LENNOX HEARTH PRODUCTS • RHAPSODY™ LINEAR DIRECT-VENT GAS FIREPLACES (MODELS RHAP42N & RHAP54N) • INSTALLATION INSTRUCTIONS fIELd WIRINg STEPS Route wiring and install electrical components in the order described in this section. 1. Route fireplace wiring. (See Figures 42 and 43)
  • Page 26: Install/Wire Remote Control System

    LENNOX HEARTH PRODUCTS • RHAPSODY™ LINEAR DIRECT-VENT GAS FIREPLACES (MODELS RHAP42N & RHAP54N) • INSTALLATION INSTRUCTIONS 2.8. On the Transmitter, press the ON button. fIELd WIRINg WARNINg (CONTINUEd) The Receiver will “beep” four times to indicate acceptance of the Transmitter’s fire hazard.
  • Page 27: Installing Fireplace Components

    LENNOX HEARTH PRODUCTS • RHAPSODY™ LINEAR DIRECT-VENT GAS FIREPLACES (MODELS RHAP42N & RHAP54N) • INSTALLATION INSTRUCTIONS INSTALLINg fIREPLACE INSTALLATION INSTRUCTIONS COMPONENTS 1. Make sure the fireplace is OFF and COLD. 2. Remove the fireplace glass door assembly, if installed (see Install all fireplace components in this section Figure 49).
  • Page 28: Installation/Removal Of Glass Door

    LENNOX HEARTH PRODUCTS • RHAPSODY™ LINEAR DIRECT-VENT GAS FIREPLACES (MODELS RHAP42N & RHAP54N) • INSTALLATION INSTRUCTIONS Installation of glass door Assembly INSTALLINg fIREPLACE COMPONENTS AVERTISSEMENT 1. While holding the door assembly by the (CONTINUEd) Ne pas utiliser l'appareil si le...
  • Page 29: Installation Of Modesty Panel

    LENNOX HEARTH PRODUCTS • RHAPSODY™ LINEAR DIRECT-VENT GAS FIREPLACES (MODELS RHAP42N & RHAP54N) • INSTALLATION INSTRUCTIONS Installation of Optional Bezel INSTALLINg fIREPLACE COMPONENTS 1. Hook the bezel upper flange to the top (CONTINUEd) edge of the glass door frame, and then...
  • Page 30: Appliance Checkout

    LENNOX HEARTH PRODUCTS • RHAPSODY™ LINEAR DIRECT-VENT GAS FIREPLACES (MODELS RHAP42N & RHAP54N) • INSTALLATION INSTRUCTIONS VERIfyINg APPLIANCE Ignitor Igniter OPERATION Pilot Hood With the gas-line installed, run the initial system checkout before closing up the front of the unit.
  • Page 31: Lighting Instructions

    LENNOX HEARTH PRODUCTS • RHAPSODY™ LINEAR DIRECT-VENT GAS FIREPLACES (MODELS RHAP42N & RHAP54N) • INSTALLATION INSTRUCTIONS LIgHTINg INSTRUCTIONS fOR yOUR SAfETy REAd BEfORE OPERATINg WARNINg: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life.
  • Page 32: Adjusting The Air Shutter

    LENNOX HEARTH PRODUCTS • RHAPSODY™ LINEAR DIRECT-VENT GAS FIREPLACES (MODELS RHAP42N & RHAP54N) • INSTALLATION INSTRUCTIONS VERIfyINg APPLIANCE OPERATION (CONTINUEd) AdjUSTINg THE AIR SHUTTER Note: Before adjusting the air shutter, the glass door assembly must be in place and secured.
  • Page 33: Finish And Trim

    LENNOX HEARTH PRODUCTS • RHAPSODY™ LINEAR DIRECT-VENT GAS FIREPLACES (MODELS RHAP42N & RHAP54N) • INSTALLATION INSTRUCTIONS Wall finish Requirements when Note: The provided Non-Combust ible fINISH fiber Board may be faced with any Installing Optional Surround/Bezel NON-combustible finish material ap- ANd TRIM 1.
  • Page 34: Finish And Trim

    LENNOX HEARTH PRODUCTS • RHAPSODY™ LINEAR DIRECT-VENT GAS FIREPLACES (MODELS RHAP42N & RHAP54N) • INSTALLATION INSTRUCTIONS fINISH ANd TRIM Insulation and combustible Min. 1" Min. 3" (CONTINUEd) Min. 1" Min. 3" material NOT ALLOWED in (25 mm) (76 mm) (25 mm)
  • Page 35: Attaching Safety-In-Operation

    LENNOX HEARTH PRODUCTS • RHAPSODY™ LINEAR DIRECT-VENT GAS FIREPLACES (MODELS RHAP42N & RHAP54N) • INSTALLATION INSTRUCTIONS ATTACHINg WARNINg LABELS INSTALLER INSTRUCTIONS - ATTACHINg SAfETy IN OPERATION WARNINgS It is the installers responsibility to ensure these warnings are properly affixed during installation. These warning labels are a critical step in informing consumers of safe operation of this appliance.
  • Page 36: Installation Accessories

    LENNOX HEARTH PRODUCTS • RHAPSODY™ LINEAR DIRECT-VENT GAS FIREPLACES (MODELS RHAP42N & RHAP54N) • INSTALLATION INSTRUCTIONS INSTALLATION ACCESSORIES Listed Secure Vent ® Components Listed Secure Vent Components Cat. No. Model description Cat. # Model description H1968 SV4.5HT-2 Horizontal Termination 17M52 SV4.5HGS-1...
  • Page 37: Gas Conversion Kit

    LENNOX HEARTH PRODUCTS • RHAPSODY™ LINEAR DIRECT-VENT GAS FIREPLACES (MODELS RHAP42N & RHAP54N) • INSTALLATION INSTRUCTIONS INSTALLATION ACCESSORIES (CONTINUEd) gAS CONVERSION kIT Listed Secure flex ® Components A gas conversion kits is available to adapt your appliance from natural Cat. #...
  • Page 38: Replacement Parts

    LENNOX HEARTH PRODUCTS • RHAPSODY™ LINEAR DIRECT-VENT GAS FIREPLACES (MODELS RHAP42N & RHAP54N) • INSTALLATION INSTRUCTIONS REPLACEMENT WARNINg PARTS failure to position the parts in accordance with these diagrams or failure to use only parts Ordering Replacement Parts specifically approved with this...
  • Page 39: Replacement Parts List

    LENNOX HEARTH PRODUCTS • RHAPSODY™ LINEAR DIRECT-VENT GAS FIREPLACES (MODELS RHAP42N & RHAP54N) • INSTALLATION INSTRUCTIONS REPLACEMENT PARTS (CONTINUEd) Replacement Parts List Contact an Lennox Hearth Products dealer to obtain any of these parts. Never use substitute materials. Use of non-approved parts can result in poor performance and safety hazards and may void the warranty.
  • Page 40: Replacement Parts

    LENNOX HEARTH PRODUCTS • RHAPSODY™ LINEAR DIRECT-VENT GAS FIREPLACES (MODELS RHAP42N & RHAP54N) • INSTALLATION INSTRUCTIONS REPLACEMENT PARTS (CONTINUEd) Replacement Parts Illustrations Note: The only parts illustrated on this page that are offered as replacement parts are those listed on the previous page.
  • Page 41 LENNOX HEARTH PRODUCTS • RHAPSODY™ LINEAR DIRECT-VENT GAS FIREPLACES (MODELS RHAP42N & RHAP54N) • INSTALLATION INSTRUCTIONS NOTES...
  • Page 42 LENNOX HEARTH PRODUCTS • RHAPSODY™ LINEAR DIRECT-VENT GAS FIREPLACES (MODELS RHAP42N & RHAP54N) • INSTALLATION INSTRUCTIONS Lennox Hearth Products reserves the right to make changes at any time, without notice, in design, materials, specifications, and prices, and also to discontinue colors, styles, and products.

This manual is also suitable for:

Rhapsody rhap54n

Table of Contents