[Startup Input Select]; [Last Used] - Panasonic PT-DZ13KE Operating Instructions Manual

[COMMAND]
[INPUT]
[LAMP SELECT]
[LAMP POWER]
[P IN P]
*1 Only for PT-DZ13KE, PT-DS12KE, PT-DZ10KE
*2 Only for PT-DZ13KE, PT-DS12KE
*3 Only for PT-DZ13KE, PT-DS12KE, PT-DW11KE. Even when the command for [HIGH] is set, it is not reflected at the execution, if the optional
Replacement lamp unit (for portrait mode) (Model No.: ET-LAD320P (1 pc), ET-LAD320PW (2 pcs)) is used.
*4 Only for PT-DZ13KE, PT-DS12KE, PT-DW11KE
*5 Only for PT-DZ10KE
10) Press the <ENTER> button.
f The [COMMAND] detailed screen is displayed.
11) Press as to select a [COMMAND].
f For [COMMAND] which requires detailed settings, the items of the detailed settings will switch each time you press qw.
12) Press the <ENTER> button.
f The command is fixed and n is displayed at the left of the selected command.
f After the command is fixed, press the <MENU> button to close the detailed setting screen.
13) Press asqw to select [STORE], and press the <ENTER> button.
Note
f If you attempt to register the setting that would make the lamp turn on for a short time, an error message will be displayed on the screen.
Set the time and command again.
f To delete a command already set, press the <DEFAULT> button on the Step 5) screen, or select [DELETE] on the Step 6) screen and press
the <ENTER> button.
f If multiple commands have been set for the same time, they are executed in chronological order starting from the smallest command
number.
f The operating time will be the local time. (x page 121)
f If an operation is executed with the remote control or control panel of the projector or with a control command before the command set in
[SCHEDULE] is executed, the command set with this function may not be executed.

[STARTUP INPUT SELECT]

Set the input when the projector is switched on to start projection.
1) Press as to select [STARTUP INPUT SELECT].
2) Press qw to switch the item.
f The items will switch each time you press the button.

[LAST USED]

[VIDEO]
[RGB1]
Chapter 4 Settings — [PROJECTOR SETUP] menu
Detailed settings of
[COMMAND]
[VIDEO]
[RGB1]
[RGB2]
[DVI-D]
[HDMI]
[SDI1]
*1
[SDI2]
*2
[DUAL]
[SINGLE]
[HIGH]
*3
[MIDDLE]
*4
[NORMAL]
*5
[ECO]
[OFF]
[USER1]
[USER2]
[USER3]
Keeps the input selected last.
Sets the input to VIDEO.
Sets the input to RGB1.
Description
Switches the input to VIDEO.
Switches the input to RGB1.
Switches the input to RGB2.
Switches the input to DVI-D.
Switches the input to HDMI.
(PT-DZ13KE, PT-DS12KE)
Switches the input to SDI1.
(PT-DZ10KE)
Switches the input to SDI.
Switches the input to SDI2.
Turns on two lamps.
Turns on one lamp. (The lamp with shorter runtime will
automatically light.)
Sets the lamp brightness to high luminance.
Sets the lamp brightness to slightly lower luminance compared to
[HIGH].
Sets the lamp brightness to high luminance.
Sets the lamp brightness to low luminance.
P IN P function is not used.
Lays out the sub-screen with the settings of [USER1].
Lays out the sub-screen with the settings of [USER2].
Lays out the sub-screen with the settings of [USER3].
ENGLISH - 117