Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Logosol E4000
Summary of Contents for Logosol E4000
- Page 1 Instruction Manual E4000 - E5000 – E6000 Three-phase electric chain saw...
- Page 2 Call Logosol and we will send you information about our entire selection of products. If there is a particular product in which you are interested, we have video films you can watch to see our products in action.
-
Page 3: Table Of Contents
Do not allow Safety rules persons who have not read • The LOGOSOL E 5000 may only be the safety instructions to operate the machine. You used for cross cutting in combination should also read the with the LOGOSOL mini-saw mill. -
Page 4: Assembly
Assembly Fit the control arm to the electric saw using four M6x20 bolts and nuts. First loosen the protective yoke. Then place the control arm in position and push two bolts through the protective yoke, the control arm and its mount, tightening the nut on the inside. Use two more bolts to fasten the other side of the control arm. -
Page 5: Assembling Bar And Chain
Assembling bar and chain First check that the unit is unplugged. Then remove the bar nuts and the bar plate. Fit the bar and chain and return the bar plate to its place. Check that the bar abuts the spacers and isn't caught on wood chips or the guiding flange for the pin bolts. -
Page 6: Chain Lubrication
Chain lubrication Because of the large motor effect, the oil pump is set at maximum when the chain saw is delivered. While the oil flow can be reduced, remember that there is only a quarter turn between max. and min. settings. Never run the saw without chain oil. -
Page 7: Frame Support
Frame support Fit the support legs to the ends of the saw mill guide rail as shown above. If the ground is loose, the saw mill and the struts ought to be attached to a wooden frame in order not to sink into the earth. -
Page 8: Cutting Equipment
Electric system The motor is fitted with a thermal overheating cut-off. Should the temperature in the motor winding be too high, the motor will stop and will not start again until it has cooled off. The chain should run counter-clockwise or towards the sawing unit on the cutting side of the bar. -
Page 9: Maintenance
Maintenance The electric saw is simple to take care of. The maintenance required is listed below. Be sure the machine is voltage free before you take it from the guide rail or do any work in the vicinity of moving parts. •... -
Page 11: Schematic
Parts list 9999-000-6000 Key Schematic Art. no Poly V-belt 5 kW motor 9999-000-6095 Lining thread, ISM M5 9999-000-6063 oil container 9999-000-6052 Guide rail brush 9999-000-6050 9999-000-6075 9999-000-6079 Junction box, complete, Phillips bolt, M5x12 5 kW Slide holder 9999-000-6033 9999-000-6070 Control arm 21 1 Plastic glide strips 9999-000-6035... - Page 12 Key Gear housing and bar fastener ail pump 9999-000- Art. no 6020 Plastic cap 9999-000- ail pipe, transparent 9999-000- 6030 6036 Lock nut, M1 0 9214-320- Cover plate 9999-000- 1305 6024 Flat washer 4510-723- Guide bar plate, upper 9999-000- 4602 6023 Rubber bushing 9999-000-...
-
Page 13: Circuit Diagram
Technical specifications Effect, E 5000 Rated effect Maximum effect app. 10 kW Electric equipment Mains feed 50 Hz 400 V 16 A, 3-phase Insulation class IP 54 Electric contact CEE system (round), 16A, with phase inverter. Other Contactor operation with help relay. Temperature sensors in windings Power transfer Poly V-belt... -
Page 14: Eu Manufacturer's Declaration
The E3000/E5000 electric chain saws may only be used together with the M5, M6 and M7 Logosol sawmills. The E4000/E5000 may not be started before the machine with which it is to be used conforms to the EU machine directive. The electric saw conforms to the requirements in the low-voltage directive 73/23/EEG and the EMC directive 89/336/EEG.