Advertisement
USER MANUAL
TRANSLATION OF ORIGINAL USER MANUAL
0458-395-5481
REV: 1
Read through the user manual carefully and make sure you understand
its contents before you use the machine.
This user manual contains important safety instructions.
WARNING! Incorrect use can result in serious or fatal injuries to the
operator or others.
PRO FEED 400V
EN
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Logosol PRO FEED 400V
Summary of Contents for Logosol PRO FEED 400V
- Page 1 USER MANUAL TRANSLATION OF ORIGINAL USER MANUAL 0458-395-5481 REV: 1 PRO FEED 400V Read through the user manual carefully and make sure you understand its contents before you use the machine. This user manual contains important safety instructions. WARNING! Incorrect use can result in serious or fatal injuries to the...
- Page 2 We are very pleased that you have demonstrated your confidence in us by purchasing this sawmill, and we will do our utmost to meet your expectations. Logosol has been manufacturing sawmills since 1989. In that time we have supplied approximately 50,000 machines to satisfied customers the world over.
-
Page 4: Safety Instructions
SAFETY INSTRUCTIONS KEY TO SYMBOLS Always use approved hearing protection WARNING! This symbol means that you when working with the machine. Even should pay particular attention and is always short exposure to high frequency noise followed by information about the relevant can damage your hearing. - Page 5 SAFETY INSTRUCTIONS THE SAFETY EQUIPMENT OF THE THE WORKSITE BAND SAWMILL WARNING! Never operate a band sawmill with a petrol-powered engine in enclosed or poorly WARNING! Never use the machine if the safety ventilated areas. This can result in death due to equipment is defective.
- Page 6 BOLTS & NUTS Definition of fasteners on following pages. Shoulder bolt Allen bolt Phillips bolt Partial thread Allen bolt Hex bolt Slotted bolt Set screw Partial thread hex bolt Hex nut Flange bolt Flange nut Partial thread flange bolt Carriage bolt Flat washer ADDITIONAL SYMBOLS DIAMETER &...
- Page 7 1 x – DK-00102 4 x – M4x10 4 x – M4x20 4 x – M4 03-02668 1 x – 4 x – M4 03-02972 1 x – 4 x – M5x20 2 x – M6x10 03-02963 1 x – 4 x –...
- Page 8 2 x – M8x20 1 x – M12x100 +M12 1 x – M12 78,5mm 4 x – M6x16 4 x – M6 2 x – M6x10 2 x – M6...
- Page 9 1 x – M6x25 2 x – M10x40 4 x – M10 2 x – M10 2 x – DK-00063...
- Page 10 4 x – M6x16 4 x – M6x12 4 x – M6x16 4 x – M6 4 x – M6x12...
- Page 11 4 x – M4x20 4 x – M5x20 2 x – M4x10 2 x – M4 2x – M4 2 x – M4x10 2 x – M4 2x – M4 01-00453 2 x – M6 1 x – 04-00141...
- Page 12 Tighten the supply chain manually as much as possible before it is mounted on the chain lock. 2 x – M6x30 2 x – M6 2 x – 04-00443 2 x – M10...
- Page 13 CONNECTION OF CABLE TRUNKS M12 8p 01-00946 (4m) 01-00945 (10m) M12 8p...
-
Page 14: Check Before Starting
CONNECTION OF CABLE TRUNKS AT FIRST START-UP Check before starting Check that the power supply is working. Proceed as follows: Run the saw head along the rail with the actuator, listen for noise and ensure that the chain is aligned between the gears. Check that no physical collision occurs during the first run along the length of the rail. -
Page 15: Control Panel
The machine works but the engine does • The motor is running hot; motor protection • Wait until the motor has cooled and not run. has tripped. resume operation; the motor must not run hot. If the problem recurs, contact Logosol. -
Page 16: Declaration Of Conformity
Declaration of conformity conformity In accordance with Directive 2006/42/EG, Annex 2A Logosol AB, Logosol AB, Arkivgatan 6, 871 53 Härnösand Fiskaregatan 2, SE-871 33 Härnösand, Sweden herewith declares that Pro Feed 400V hereby declares that Pro Feed 400V has been manufactured in conformity with the...
Need help?
Do you have a question about the PRO FEED 400V and is the answer not in the manual?
Questions and answers