Advertisement
Table of Contents
- 1 Table of Contents
- 2 Safety Rules
- 3 Assembly
- 4 Assembling Bar and Chain
- 5 Chain Lubrication
- 6 Frame Support
- 7 Control Light and Electric System
- 8 Cutting Equipment
- 9 Maintenance
- 10 Belt Tension
- 11 Schematic
- 12 Parts List
- 13 Circuit Diagram
- 14 Technical Specifications
- 15 EU Manufacturer's Declaration
- 16 Declaration of Conformity
- Download this manual
Advertisement
Table of Contents
Related Manuals for Logosol E5000
Summary of Contents for Logosol E5000
- Page 1 Instruction Manual E5000 Three-phase electric chain saw Swedish Wood Processing Products...
- Page 2 The E 5000 is a powerful, easy-to-use electric chain saw. Do not hesitate to call us here at LOGOSOL with questions and opinions about our equipment. It is our goal that you should join the list of satisfied owners of a LOGOSOL product.
-
Page 3: Table Of Contents
For your own safety, read all safety precau- tions carefully and do not start the machine before you have understood all of them. Do The LOGOSOL E 5000 may only be used for cross • not allow persons who have not read the cutting in combination with the LOGOSOL mini-saw safety instructions to operate the machine. -
Page 4: Assembly
Assembly Fit the control arm to the electric saw using four M6x20 Move the attachment for the feed line on the saw mill bolts and nuts. First loosen the protective yoke. Then log dog. Replace the rear M6x16 bolt holding the slide place the control arm in position and push two bolts with a longer M6x25 fitted with a sleeve as shown be- through the protective yoke, the control arm and its... -
Page 5: Assembling Bar And Chain
Assembling bar and chain Chain direction First check that the unit is unplugged. Then remove the If it is not possible to pull a whole chain tooth out of the bar nuts and the bar plate. Fit the bar and chain and bar using the index finger and the thumb, the chain is return the bar plate to its place. -
Page 6: Chain Lubrication
Chain lubrication After some use, the colour on the bar will flake off, re- Because of the large motor effect, the oil pump is set at vealing the blue-coloured, induction tempered wearing maximum when the chain saw is delivered. While the surface. -
Page 7: Frame Support
Frame support Fit the support legs to the ends of the saw mill guide rail Adjust the leg length by loosening the nut in the guide as shown above. If the ground is loose, the saw mill and rail and turning the leg. The legs should neither pull the struts ought to be attached to a wooden frame in down nor push up on the guide rail, only holding it firmly order not to sink into the earth. -
Page 8: Control Light And Electric System
Control light and electric system Cutting equipment When current is flowing to the saw, the control lamp will shine Because of the high motor effect, it is essential to stop sawing faintly. In strong sun light, you’ll need to shade it to see its if the chain gets dull. -
Page 9: Maintenance
Maintenance The electric saw is simple to take care of. The maintenance required is listed below. Be sure the machine is vol- tage-free before you take it from the guide rail or do any work in the vicinity of moving parts. Make sure that there is always chain oil in the container when sawing. -
Page 10: Schematic
18 19 Schematic... -
Page 11: Parts List
Parts list Key Schematic Art. no. 16. Belt pulley lock screw 9999-000-6046 5 kW motor 9999-000-6095 17. Poly V-belt 9999-000-6000 Oil container 9999-000-6052 18. Lining thread, ISM M5 9999-000-6063 Junction box, complete, 5 kW 9999-000-6075 19. Guide rail brush 9999-000-6050 Control lamp 9999-000-6078 20. -
Page 12: Circuit Diagram
Key Gear housing and bar fastener Art. no. Plastic cap 9999-000-6030 Lock nut, M10 9214-320-1305 Flat washer 4510-723-4602 Rubber bushing 9999-000-6069 Oil pump drive 9999-000-6021 Phillips bolt, M5x16 9999-000-6002 Lock nut, M5 9214-320-0700 Oil pump 9999-000-6020 Oil pipe, transparent 9999-000-6036 Cover plate 9999-000-6024 Guide bar plate, upper... -
Page 13: Technical Specifications
Technical specifications Effect, E 5000 Rated effect 5 kW / 220V 4,4 kW) Maximum effect app. 10 kW / 220V 8 kW Electric equipment SE version Mains feed 50 Hz 400 V 16 A, 3-phase Insulationclass IP 54 Electric contact CEE system (round), 16A, with phase inverter. - Page 14 Circuit diagram Circuit diagram US-version 220 V Circuit diagram 400V (220V see last page) Current Swedish rules require that the saw be connected using a 5-lead cable of which one must be an earth connection. Only persons with the proper credentials should make repairs or adjustments to the electrical equipment, as a wrong connection can endanger lives.
-
Page 15: Declaration Of Conformity
EN ISO 12100-1, -2:2003, EN 60204-1:2006, EN 61000-6-1, -3. The electric saw units E 4000, E 5000 and E 8000 may only be used as saw units on Logosol's sawmills M5, M6 and M7. Härnösand, 26 February 2008... - Page 16 English LOGOSOL AB, Sverige SE-871 53 Härnösand Industrigatan 13 Telefax 0611-182 89 Telefon 0611-182 85 LOGOSOL Inc, USA Madison Mi 391 30 P.O. Box 660 Fax 601-856 95 35 Phone 601-856 18 89 info@logosol.com www.logosol.com E5000-001025-002...