Table of Contents
Advertisement
USER MANUAL
USER MANUAL IN ORIGINAL FORMAT.
LOGOSOL Speed Saw
Read through the user manual carefully and make sure you understand its contents
before you use the planer/moulder.
This user manual contains important safety instructions.
warninG! Incorrect use can result in serious personal injury or even death to the
operator or others.
Advertisement
Table of Contents
Related Manuals for Logosol E4
Summary of Contents for Logosol E4
-
Page 1: User Manual
USER MANUAL USER MANUAL IN ORIGINAL FORMAT. LOGOSOL Speed Saw Read through the user manual carefully and make sure you understand its contents before you use the planer/moulder. This user manual contains important safety instructions. warninG! Incorrect use can result in serious personal injury or even death to the... - Page 2 Bengt-Olov Byström Founder and Chairman of the Board LOGOSOL AB, Härnösand, Sweden LOGOSOL is engaged in continuous development of its products. We must therefore reserve the right to change the design and form of our products. Text: Mattias Byström Translation: Anna Byström Olsgren...
-
Page 3: Table Of Contents
Machine description Tools required Assembly Lifting instructions & setup Fitting guide bar & chain Chain lubrication & water cooling Adjustable slide blocks Sawing with the Logosol Speed Saw Cutting equipment Storing the electric saw Elecrical system Technical data EC Declaration... -
Page 4: Safety Instructions
• LOGOSOL E8 Speed Saw is exclusively intended sawdust duct. for rip sawing with the LOGOSOL Sawmill. -
Page 5: Overview
LOGOSOL Speed Saw overview 6608-000-0005 E8 Speed Saw 400V 6608-000-0010 E8 Speed Saw 230V 6608-000-0015 E4 Speed Saw 400V 6608-000-0020 E4 Speed Saw 230V 8000-001-000X Motor, 4kW 6608-001-000X Motor, 8kW 6608-001-0060 Chassis 3008-010-0050 Guide bar 50 cm 3008-010-0070 Guide bar 70 cm... - Page 6 Forward Guide bar side Backward Operator side...
- Page 7 LOGOSOL Speed Saw...
-
Page 9: Machine Description
LOGOSOL Speed Saw machine description LOGOSOL Speed Saw is a chainsaw unit that is for the Speed Saw and are available in different lengths intended for usage on the LOGOSOL Sawmill. supplied by LOGOSOL. The Speed Saw has no own... -
Page 10: Assembly
assembly 1. Fit the motor mount (20)* with four M8x20 countersunk Allen screws. Use medium strength threadlocker and torque the screws to 25 Nm. Then fit the cover plate (18) with two countersunk Allen screws. * Position no. in the exploded views. 2. - Page 11 LOGOSOL Speed Saw 3. Fit spacers, pulley, etc. in following order: spacer 12 mm (22) , spacer 5 mm (23), chain guide (24), chain pulley (25), chain guide, spacer 12 mm, spacer 5 mm, spacer 10 mm (26) and last the motor shaft washer (27).
- Page 12 5. Fasten the complete alu profiles by fitting two M6 square nuts in each alu profile, and then fasten them by using M6x16 hex screws incl. washers. Then tighten the screws in the cover plates. 6. Fit the feeder holder (11) to the chassis (2) with three M6x10 hex screws incl.
- Page 13 LOGOSOL Speed Saw 7. Fasten the cover plate (34) with four M8x35 incl. washers. Do not tighten the screws, but let there be a play of approx. 5-6 mm (approx. 1/4’’) between the cover plate and the bar plate (33). Then fit the right and left handles (5, 6) using M6x12 Allen screws incl.
- Page 14 9. Rivet the bottle holder on to the motor. On the 8kW motor two holes have to be drilled. On the 4kW motor you can use one of the holes that holds the fan cover in position, and only one new hole has to be drilled.
- Page 15 LOGOSOL Speed Saw 11. Take the line and thread it through the spring, the plastic bushing and the tube as shown above. Tie a knot at the line end and fit the plastic bushing and the spring in the spring attachment.
- Page 16 13. The line holder (12) is screwed to the electric saw with two M6 flange nuts. 14. The electric cable from the feeder unit is threaded through the cable hook (19), which works a strain relief. The hook is then hung up on the chain tensioner knob.
-
Page 17: Lifting Instructions & Setup
Fit the guide bar and chain after the saw has been The Speed Saw can be driven by electric or manual feed. mounted on the LOGOSOL Sawmill. The Speed Saw should In both cases a line holder is fitted to the rear edge of the be mounted on the guide rail of the sawmill before power Speed Saw. -
Page 18: Chain Lubrication & Water Cooling
& water cooling Oil pump and automatic water cooling In its basic design Logosol Speed Saw has a solenoid valve that controls the supplying of oil. The oil runs If you want to upgrade your Speed Saw to get down on the bar by gravity feed. -
Page 19: Sawing With The Logosol Speed Saw
LOGOSOL Speed Saw sawing with the logosol speed saw before each worK session afTer each worK session • Make sure that the saw is correctly mounted on • Disconnect the power by pulling out the plug of the guide rail. -
Page 20: Elecrical System
Read the instructions for than 25 m it should be 4 mm (3/16’’). the feed unit. LOGOSOL supplies extension cords that are 2.5 and 4 mm with 16A socket and plug. The Speed Saw consumes a lot of electricity when it is heavy loaded, so it is crucial that the electrical equipment is in perfect condition. - Page 21 LOGOSOL Speed Saw...
-
Page 23: Ec Declaration
Declaration of conformity Logosol AB Fiskaregatan 2 S-871 33 Härnösand Phone: +46 611 18285 hereby guarantees that LOGOSOL Speed Saw, with ref. no. 6608-000-0005, 6608-000-0010, 6608- 000-0015, 6608-000-0020 is manufacturedin conformity with Machinery Directive 2006/42/ EG, EMC Directive 2004/108/EG and LVD Directive... - Page 24 LogosoL sweden Fiskaregatan 2, S-871 33 Härnösand Phone +46 (0)611-182 85 | Fax +46 (0)611-182 89 info@logosol.se | www.logosol.se...