Table of Contents
Advertisement
Quick Links
user manual
TRANSLATION OF ORIgINAL uSeR mANuAL.
ARTIcLe NO: 0458-395-4007
circular resaw kS150
Read through the user manual carefully and make sure you understand its contents before
you use the machine.
This user manual contains important safety instructions.
Warning! Incorrect use can result in serious or fatal injuries to the operator or others.
1
Advertisement
Table of Contents
Related Manuals for Logosol KS150
Summary of Contents for Logosol KS150
-
Page 1: User Manual
TRANSLATION OF ORIgINAL uSeR mANuAL. ARTIcLe NO: 0458-395-4007 circular resaw kS150 Read through the user manual carefully and make sure you understand its contents before you use the machine. This user manual contains important safety instructions. Warning! Incorrect use can result in serious or fatal injuries to the operator or others. - Page 3 Logosol Circular Resaw Welcome to Logosol! We are pleased that you have placed your trust in us by choosing the Circular Resaw, and we promise to do our best to satisfy your expectations. Logosol began production of the Logosol Sawmill in 1988. Since then we have delivered approximately 20.000...
- Page 4 Information about this manual Whenever this symbol appears, a tip follows that will simplify or improve the results. LOGOSOL is constantly developing its products. For that reason we reserve the right to make changes in the design and construction of our products.
-
Page 5: Table Of Contents
Table of Contents Page: Safety Instructions Machine Description Moving the Resaw Setting up the Resaw Electrical Connection Resawing Maintenance Belt Tensioning Changing Saw Blade The Control Panel Adjusting the Feeding Circuit Diagram Technical Data CE – Manufacturer’s Declaration... -
Page 6: Safety Instructions, 2 Pages
Safety Instructions, 2 pages “ WARNING! “. Pay extra attention If used incorrectly, the Circular Resaw when this symbol appears in the can cause serious injury. text. The most important safety instructions are found on this page and the next. For your own safety, do not begin Additional instructions will appear in working with the machine before... - Page 7 direction, and that the feeding speed is The safety distance for persons other than adjusted for the work piece that is to be the operator is 10 m (33 ft) seen from the sawn. in-feed side of the machine due to the danger of work pieces being hurled out Before start, make sure that...
-
Page 8: Machine Description
Machine Description Moving the Resaw Logosol Circular Resaw is designed for The Circular Resaw should be lifted with resawing squared timber. The machine is a fork-lift truck or the like. The machine basically a chassis with a level table on the should stand on a Euro pallet when being top side. -
Page 9: Setting Up The Resaw
Circular Resaw. machine and the wall. Logosol recommends that you think about the ergonomics involved in handling timber If it is not full daylight, ensure that you both to and from the machine. There are a have adequate main lighting. - Page 10 (48 4x10mm Logosol’s Circular Resaw (article no: 9999- wood screws) 000-0020) and, if required, a table extension 3. Carefully tap down the the aluminium (9999-000-9999).
- Page 11 The Circular Resaw with mounted in-and out-feed tables. Adjusting the Tables and Rollers: 1. The inner roller should be approx. 1 mm (0.04”) above the machine table. Place a straight board or a spirit level on the machine table with a 1 mm thick spacer between them.
-
Page 12: Electrical Connection
Electrical Connection wall, which should be no more than 10m (33 ft) from the machine. When the machine is set up according to the above instructions, it can be connected to The machine is already adjusted and test the correct volatage (see Technical Data). run, but it may be necessary to tweak the Make sure that the machine runs in the fence angles in order to make the machine... -
Page 13: Changing Saw Blade
When loosening or tightening the nut that riving knife must be adjusted. Only use holds the saw blade, you should fixate the saw blades delivered from Logosol. saw blade by sticking a rod through one of the openings in it. -
Page 14: The Control Panel
The Control Panel Adjusting the Feeding The feeding will be damaged if the knob for adjusting feeding speed is turned when the feeding is not running. The feeding speed may only be adjusted when the feeding is running. The speed ranges from 4 to 12 m/minute (13- 39 ft/min.). -
Page 15: Circuit Diagram
Circuit Diagram... -
Page 16: Technical Data
Technical Data. Elctrical System Continuous output, Saw Motor: 7.5 kW Continuous output, Feeding Motor: 0.25 kW Electricity supply: 50/60 Hz, 3-phase, 230 V Coupled enclosure, degree of protection: IP 54 Speed of Rotation Saw Motor: 1500rpm Feeding Motor: 1500rpm Saw Blade Speed of rotation: 1750rpm Saw blade type:... -
Page 19: Ce - Manufacturer's Declaration
Declaration of Conformity The manufacturer, Logosol AB, Industrigatan 13, S-871 53 Härnösand, tel. +46 (0)611 18285, hereby declares that Logosol Circular Resaw, art. no. 5210-000-1000 is manufactured in accordance with Machinery Directive 98/37/EG Examinated by: no. 0404 - SMP Swedish Machinery Testing Institute AB, Uppsala, Sweden. - Page 20 Spares your back and makes you stronger! Full control of the log, even when you take a new grip. www.logosol.com Swedish Wood Processing Products LOGOSOL Sweden SE-871 33 Härnösand Fiskaregatan 2 Telefax +46 611-182 89 Telefon +46 611-182 85 info@logosol.com www.logosol.com...