CONTENTS Introduction Operation Notes Features Panel Layout Panel Descriptions Connecting And Operating The 4x4 Matrix for HDMI 1.3 EDID Modes RMT-16IR Remote Description 4x4 Matrix for HDMI 1.3 Remote Installation 10 IR Channel Confi guration 11 RS-232 Serial Communication Control 12 Specifi...
Congratulations on your purchase of the 4x4 Matrix for HDMI 1.3. Your complete satisfaction is very important to us. Gefen Gefen delivers innovative, progressive computer and electronics add-on solutions that harness integration, extension, distribution and conversion technologies. Gefen’s reliable, plug-and-play products supplement cross-platform computer systems, professional audio/video environments and HDTV systems of all sizes with hard-working solutions that are easy to implement and simple to operate.
OPERATION NOTES READ THESE NOTES BEFORE INSTALLING OR OPERATING THE 4X4 MATRIX FOR HDMI 1.3 • You should connect all the cables and power supply prior to connecting power to the HDMI sources and 4x4 Matrix for HDMI 1.3. • When powering the sources, the display needs to point to the source input.
FEATURES Features • Switch easily between any four HDMI 1.3 sources • Distributes any of the four inputs to any or any combination of the four HDMI output displays • Maintains high resolution video - beautiful, sharp HDTV resolutions up to 1080p, 2k, and computer resolutions up to 1920 x 1200 are easily achieved •...
PANEL DESCRIPTIONS IR (Infrared) Receiver This receiver will accept command for switching between HDMI input devices using the included RMT-16IR remote control. Power LED Indicator This LED will become active once the included 5V DC power supply is properly connected between the unit and a open wall power receptacle. Display 1-4 Selected Input LED Indicator There is a set of 4 LEDs for each of the four output ports.
CONNECTING AND OPERATING THE 4X4 MATRIX FOR HDMI 1.3 How to Connect the 4x4 Matrix for HDMI 1.3 Connect up to 4 HDMI source devices to the 4x4 Matrix for HDMI 1.3 using the included HDMI cables. NOTE: The display connected to the port labeled OUT 1 will have its EDID used when the external EDID mode is active.
EDID MODES EDID. What is it and what is it used for? Under normal circumstances, an source device (digital and analog) will require information about a connected device/display to assess what resolutions and features are available. The source can then cater its output to send only resolutions and features that are compatible with the attached device/ display.
RMT-16IR REMOTE DESCRIPTION The RMT-16IR remote control will allow the user to select which source will be routed R remote control will allow the user to select which source to which output. Each of the 4 outputs are assigned a group of 4 buttons that will ut.
4X4 MATRIX FOR HDMI 1.3 REMOTE INSTALLATION Remove battery cover from the back of the RMT-16-IR remote. Verify that DIP switches 1 & 2 are in the down (OFF) position. Insert the battery, hold the battery so that you can see the positive side facing up.
IR CHANNEL CONFIGURATION How to Resolve IR Code Confl icts In the event that IR commands from other remote controls confl ict with the supplied RMT-16IR remote control, changing the remote channel will alleviate this issue. The RMT-16IR remote control has a bank of DIP (Dual Inline Package) switches for confi...
RS-232 SERIAL COMMUNICATION CONTROL 5 4 3 2 1 1 2 3 4 5 9 8 7 6 6 7 8 9 Only Pins 2 (RX), 3 (TX), and 5 (Ground) are used on the RS-232 serial interface Binary Table ASCII Corresponding Binary...
SPECIFICATIONS Video Amplifi er Bandwidth ............... 225 MHz Input Video Signal ................1.2 Volts p-p Input DDC Signal ................. 5 Volts p-p (TTL) Single Link Range ..............1080p/1920 x 1200 HDMI Connector ..............Type A 19-Pin Female Remote Control Port ........... RS-232 female, mini-stereo Power Consumption ...............