Zte ZXR10 5900 Series User Manual page 114

ZXR10 5900/5200 Series User Manual (Ethernet Switching Volume)
102 Confidential and Proprietary Information of ZTE CORPORATION
The configurations of S1 are as follows:
ZXR10(config)# interface gei_1/1
ZXR10(config－gei_1/1)#switch mode trunk
ZXR10(config－gei_1/1)#exit
ZXR10(config)# vlan 10
ZXR10(config-vlan10)# switchport tag gei_1/1
ZXR10(config-vlan10)# exit
ZXR10(config)# cfm create md session 15 name md15 level 7
ZXR10(config-md)# ma create session 32 name ma1
ZXR10(config-md-ma)#protect vlan
ZXR10(config-md-ma)# primary vlan 10
ZXR10(config-md-ma)# speed slow
ZXR10(config-md-ma)#create mep session 64 1 direction down
ZXR10(config-md-ma)# assign mep 1 to interface gei_1/1
ZXR10(config-md-ma)#
ZXR10(config-md-ma)#create rmep session 2 2 remote-mac
The configurations of S2 are as follows:
ZXR10(config)# interface gei_2/1
ZXR10(config－gei_2/1)#switch mode trunk
ZXR10(config－gei_2/1)#exit
ZXR10(config)# interface gei_2/2
ZXR10(config－gei_2/2)#switch mode trunk
ZXR10(config－gei_2/2)#exit
ZXR10(config)# vlan 10
ZXR10(config-vlan10)# switchport tag gei_2/1
ZXR10(config-vlan10)# switchport tag gei_2/2
ZXR10(config-vlan10)# exit
ZXR10(config)# cfm create md session 15 name md15 level 7
ZXR10(config-md)# ma create session 32 name ma1
ZXR10(config-md-ma)#protect vlan
ZXR10(config-md-ma)# primary vlan 10
ZXR10(config-md-ma)# speed slow
ZXR10(config-md-ma)#create mip session 63 name mip63
ZXR10(config-md-ma)# assign mip 63 interface
ZXR10(config)# cfm enable
The configurations of S3 are as follows:
ZXR10(config)# interface gei_3/1
ZXR10(config－gei_3/1)#switch mode trunk
ZXR10(config－gei_3/1)#exit
ZXR10(config)# vlan 10
ZXR10(config-vlan10)# switchport tag gei_3/1
ZXR10(config-vlan10)# exit
ZXR10(config)# cfm create md session 15 name md15 level 7
ZXR10(config-md)# ma create session 32 name ma1
ZXR10(config-md-ma)#protect vlan
ZXR10(config-md-ma)# primary vlan 10
ZXR10(config-md-ma)# speed slow
ZXR10(config-md-ma)#create mep session 62 2 direction down
ZXR10(config-md-ma)# assign mep 2 to interface gei_3/1
ZXR10(config-md-ma)#
ZXR10(config-md-ma)#create rmep session 2 1 remote-mac
ZXR10(config)# cfm enable
To enable LT function on S1, use the following command.
ZXR10# cfm ltm md 15 ma 32 smep-id 1 dmep-id 2
Interface that S1 views is as follows:
Linktrace to 00d0.d052.2800: timeout 5 seconds, 64 hops, trans-id 1.
Please wait 5 seconds to print the result.
---------------------------------------------------------------
Hops MAC ADDRESS Ingress Action
mep 1 state enable
00d0.d052.1200
mep 2 state enable
00d0.d052.2800
Egress Action
gei_2/1
Relay Action