Fast Forward/Rewind; Setting The Cue Point - Denon DN-D4500MK2 Owner's Manual

Fast forward/Rewind

There are four methods for fast forward/rewinding.
n Fast forward/Rewind using shuttle ring and jog wheel
(2) Starting playback from the Middle of a track (Manual Search)
During playback, turn the shuffle ring.
• When the track is selected with the TRACK SELECT knob o and the PLAY/PAUSE button !1 is pushed,
If turned in the FWD direction, the playback point is moved to the forward direction, and playback is
playback starts from the beginning of that track. If you wish to start from a different position, use the
resumed from the new point.
procedure described below to search for the desired position.
If turned in the RVS direction, the playback point is moved to the reverse direction, and playback is
resumed from the new point.
During playback, turn the jog wheel (inner side).
If turned in the FWD direction, the playback speed increases.
If turned in the RVS direction, the playback speed decreases.
1
During pause, turn the shuffle ring.
If turned in the FWD direction, the pause point is moved to the forward direction, and pause mode is set
at the new point.
If turned in the RVS direction, the pause point is moved to the reverse direction, and pause mode is set
at the new point.
During pause, turn the jog wheel (inner side).
If turned in the FWD direction, the pause point is moved to the forward direction frame by frame, and
pause mode is set at the new point.
If turned in the RVS direction, the pause point is moved to the reverse direction frame by frame, and
pause mode is set at the new point.
2
Find the play start position.
Turn the shuttle ring !7 to change the
playback position quickly. (Search for the
approximate playback position.)
The fast forward/reverse mode
SEARCH is set when the shuttle ring
SCAN
6 7
(outer side) !7 is turned.
The speed changes according to
the angle at which the ring is
RVS FWD
RVS FWD
turned.
• When operated during playback, playback
resumes after the operation.
• When playback is started, the jog wheel is
set to the bend mode.
• When turned fully in either direction, the
playback position jumps about 10 seconds.
The jump time can be selected in the preset
mode from 10, 20, 30 or 60 sec.
Turn the jog wheel y. (Search for the precise
playback position.)
When the jog wheel (inner side)
SEARCH SCAN
y is turned, the frame move
6 7
mode is set.
The playback position can be
moved in units of one frame.
RVS FWD
Listen to the sound and find the desired play
start position.
NOTE:
• For MP3 discs, frames are not displayed,
however frame resolution is audible by turning
the jog wheel (inner side) y.

Setting the cue point

By setting a cue point, the track can be played back from the set position.
n Setting the cue point
Pause the track in the position where you want to set the cue point, and press
The cue point is set at the paused position.
• Irrespective of the mode, the cue point is set at the start of the track when the track is loaded.
Shockproof memory
• A maximum of approximately 20 seconds
n Returning to the cue point
uncompressed audio data is stored into memory
• Playback stops, returns to the position where you want to playback again (cue point), and is paused
(per drive). This guards audible interruptions due
to external mechanical shocks such as bumps (back cue function).
or other hard vibrations.
• When this function is used, playback can always be started from the same position.
• If advanced data reading is not possible due to
During playback, press
scratches or dirt on the disc, playback stops
once the data stored up to that point is read.
Playback stops, cues to the playback start position (cue point), and pauses.
n Moving the cue point
There are two methods for moving the cue point, using the shuttle ring, or using the jog wheel.
Setting with shuttle ring and jog wheel
1
During pause, turn the shuttle ring in the forward or reverse direction to move the
cue point while listening to the playback sound.
2
If the jog wheel is turned in the forward or reverse direction, you can move the cue
point while listening to the playback sound frame by frame.
3
CUE
Press .
The cue point is set at the moved position.
Press 13 .
The cue point is set at the moved position, and playback starts.
See the illustration on the previous page for details of the buttons used for the
18
operations on this page.
PITCH/BRAKE
6
• There are two ways to change the playing speed.
• Adjust the Pitch using the pitch slider !3 .
• The PITCH BEND button !2 or jog wheel y can be used to temporarily change the pitc
• The playing speed can be changed greatly to achieve effect similar to those achievable w
• If you wish to preserve the original key of sound, set the Key Adjust function to ON.
(1) Pitch
[Pitch slider]
Set the variable speed mode.
Push the PITCH button !4 to light
1
CUE .
-1
the PITCH LED.
• PITCH → KEY (key adjust) → OFF
(Green) (Orange) (Off) (LED color)
Pitch
The Pitch decreases
decreases
(2) Starting playback from the Middle of a track (Manual Se
when the pitch slider !3
is moved upwards,
1
-2
0% • When the track is selected with the TRACK SELECT knob o and the PLAY
increases when the pitch
playback starts from the beginning of that track. If you wish to start from
slider !3 is moved
procedure described below to search for the desired position. Pitch
downwards.
increases
Find the play start position.
DN-D4500 has six pitch ranges,
Turn the shuttle ring !7 to change the
4%, 10%, *16%, 24%, 50% and
playback position quickly. (Search for the
100%. (*Max MP3) When the
approximate playback position.)
RANGE button !4 is pushed
for more than 1 sec, the pitch
The fast forward/reverse mode
range can be selected by turning
is set when the shuttle ring
1 SEARCH SCAN
-3
6 7
the TRACK SELECT knob o.
(outer side) !7 is turned.
• When the TRACK SELECT The speed changes according to
knob o is pushed down the the angle at which the ring is
1
RVS FWD
RVS FWD
pitch range is entered and turned.
the pitch range selection
• When operated during playback, playback
mode is completed.
resumes after the operation.
• When playback is started, the jog wheel is
set to the bend mode.
(2) BRAKE
• When turned fully in either direction, the
• Use this function to achieve effect similar to analog players. playback position jumps about 10 seconds.
The jump time can be selected in the preset
mode from 10, 20, 30 or 60 sec.
Push the BRAKE button i to light
the BRAKE LED.
Turn the jog wheel y. (Search for the precise
• The effect sound is similar to
playback position.)
a DJ turntable coming to a
1 When the jog wheel (inner side)
quick stop. This effect can
SEARCH SCAN
y is turned, the frame move
6 7
be achieved by pushing the
mode is set.
PLAY/PAUSE button !1
The playback position can be
during playback.
moved in units of one frame.
2
RVS FWD
Listen to the sound and find the desired play
start position.
NOTE:
Operations during playback
CUE .
[PITCH BEND button]
Push the PITCH BEND + (or
PITCH BEND –) button !2 .
• The Pitch increases or
decreases temporarily wh
PITCH BEND + or PITCH
2
-1
– button !2 is pushed.
• The extent to which the PI
!2 changes the Pitch is pr
amount of time the butto
longer the button is held
the percentage of change
Set the jog wheel to the p
During playback, pitch bend
Shockproof memory
Jog wheel.
• A maximum of app
• The playing speed increas
uncompressed audio d
gradually when the jog wh
(per drive). This guards
y is turned clockwise and
to external mechanica
2
decreases gradually when
-2
or other hard vibration
wheel y is turned
• If advanced data read
counterclockwise. When
scratches or dirt on
the jog wheel y, the play
once the data stored u
to the previous speed.
• When playback is stoppe
wheel is set to the search