Denon DN-S1200 Service Manual

Denon DN-S1200 Service Manual

Cd/usb media player & controller
Hide thumbs Also See for DN-S1200:
Table of Contents

Advertisement

MODEL
DN-S1200
For purposes of improvement, specifications and
design are subject to change without notice.
Please use this service manual with referring to the
operating instructions without fail.
Some illustrations using in this service manual are
slightly different from the actual set.
SERVICE MANUAL
CD/USB MEDIA PLAYER & CONTROLLER
PROFESSIONAL BUSINESS COMPANY
JP
E3
E2
注 意
サービスをおこなう前に、このサービスマニュアルを
必ずお読みください。本機は、火災、感電、けがなど
に対する安全性を確保するために、さまざまな配慮を
おこなっており、また法的には「電気用品安全法」に
もとづき、所定の許可を得て製造されております。
従ってサービスをおこなう際は、これらの安全性が維
持されるよう、このサービスマニュアルに記載されて
いる注意事項を必ずお守りください。
本機の仕様は性能改良のため、予告なく変更すること
があります。
補修用性能部品の保有期間は、製造打切後 8 年です。
修理の際は、必ず取扱説明書を参照の上、作業を行っ
てください。
本文中に使用しているイラストは、説明の都合上現物
と多少異なる場合があります。
Ver. 2
Please refer to the
MODIFICATION NOTICE.
EK
E2A E2C E1K EUT
X0379 V.02 DE/CDM 0902

Advertisement

Table of Contents
loading

Summary of Contents for Denon DN-S1200

  • Page 1 Ver. 2 Please refer to the MODIFICATION NOTICE. SERVICE MANUAL MODEL E2A E2C E1K EUT DN-S1200 CD/USB MEDIA PLAYER & CONTROLLER 注 意 サービスをおこなう前に、このサービスマニュアルを 必ずお読みください。本機は、火災、感電、けがなど に対する安全性を確保するために、さまざまな配慮を おこなっており、また法的には「電気用品安全法」に もとづき、所定の許可を得て製造されております。 従ってサービスをおこなう際は、これらの安全性が維 持されるよう、このサービスマニュアルに記載されて いる注意事項を必ずお守りください。 ● 本機の仕様は性能改良のため、予告なく変更すること For purposes of improvement, specifications and ● があります。...
  • Page 2: Safety Precautions

    DN-S1200...
  • Page 3 ◎指定部品の使用! 定格(定格電力、耐圧)を持ったものを使用しても安全性 セットの部品は難燃性や耐電圧など安全上の特性を持っ が維持されるとは、 限りません。 安全上の特性を持った部 たものとなっています。 従って交換部品は、 使用されてい 品は、 このサービスマニュアルの配線図、 部品表につぎの たものと同じ特性の部品を使用してください。特に配線 ように表示していますので必ず指定されている部品番号 図、部品表に z 印で指定されている安全上重要な部品は のものを使用願います。 必ず指定のものをご使用ください。 (1) 配線図… z マークで表示しています。 ◎部品の取付けや配線の引きまわしは、 (2) 部品表… z マークで表示しています。 元どおりに! 指定された部品と異なるものを使用した場 安全上、テープやチューブなどの絶縁材料を使用したり、 合には、感電、火災などの危険を生じる恐 プリント基板から浮かして取付けた部品があります。 また れがあります。 内部配線は引きまわしやクランパーによって発熱部品や 高圧部品に接近しないように配慮されていますので、 これ らは必ず元どおりにしてください。 DN-S1200...
  • Page 4 DIMENSION DN-S1200...
  • Page 5 TOP CASE Assembly SCREWS 4P wire cable SCREWS 27P FFC cable Rear side BOTTOM CASE UNIT Note : Do not fail to pull AC cord from wall outlet before dis- 注意: FFC ケーブルとワイヤーを抜く前に、AC コードをコ connect the FFC cable and wire. ンセントから抜いてください。 DN-S1200...
  • Page 6 14P FFC cable MAIN PWB UNIT MAIN PWB UNIT SCREWS Rear side SCREWS Rear side Note : Do not fail to pull AC cord from wall outlet before dis- 注意: FFC ケーブルとワイヤーを抜く前に、AC コードをコ connect the FFC cable and wire. ンセントから抜いてください。 DN-S1200...
  • Page 7 (1) Remove the 2 screws on the front side and the 2 (1) 前面と底面のねじ各 2 本をはずす。 screws on the bottom side. (2) CD MECHA UNIT を引き上げ、取り外す。 (2) Pull up the CD MECHA UNIT and Remove the CD MECHA UNIT. CD MECHA. UNIT Rear Side BOTTOM CHASSIS SCREWS SCREWS DN-S1200...
  • Page 8 (3) AC INPUT PWB UNIT を矢印の方向に引き出し、 AC (3) Pull the AC INPUT PWB Unit to the direction of arrow CORD と一緒にはずす。 and remove the AC INPUT PWB Unit and AC CORD. CORD BUSH AC INPUT UNIT SCREW Rear Side SCREW BOTTOM CHASSIS DN-S1200...
  • Page 9 (5) Remove the 3 screws on the rear side. (5) 後面側 のねじ 3 本をはずす。 (6) Pull up the POWER PWB Unit and remove the POW- (6) POWER PWB UNIT を引き上げはずす。 ER PWB Unit. SCREWS POWER PWB UNIT Rear Side SCREWS BOTTOM CASE DN-S1200...
  • Page 10 (2) TOP CASE UNIT を逆さまにする。 (3) Remove the 7 screws on the CHASSIS COVER and (3) CHASSIS COVER のねじ 7 本をはずしてから CHASSIS then pull out the CHASSIS COVER. COVER を引き抜く。 SCREWS SCREWS SHASSIS COVER Rear side TOP CASE UNIT DN-S1200...
  • Page 11 FRONT SUB PANEL. はずす。 (7) Pull up the FRONT SUB PANEL and remove the (7) FRONT SUB PANEL を引き上げて取りはずす。 FRONT SUB PANEL. SENSOR UNIT SCREWS SCREW FRONT SUB PANEL SPACER GND SCREWS TOP CASE UNIT Rear Side DN-S1200...
  • Page 12 (8) Remove the 15 screws on the PANEL PWB UNIT. (8) PANEL PWB UNIT のねじ 15 本をはずしてから、 PANEL PWB UNIT をはずす。 And then remove the PANL PWB UNIT. SCREWS SCREWS SCREWS PANEL PWB UNIT TOP CASE UNIT DN-S1200...
  • Page 13 Measurement of the count value when the touch sensor section is not being touched, and measurement and judgment of the amount of change of the count value when the touch sensor section is being touched. (5) タッチ測定 (Touch MEAS) タッチ検出部の非タッチ時のカウント値の測定と、タッチ時のカウント値の変化量の測定および判定。 DN-S1200...
  • Page 14 (2) The displayed mode can be executed by pressing the PARAMETERS knob. The following appears on the lower tier of the VFD segment display section: 正常終了時 When the process has completed normally: 異常終了時 When the process has completed abnormally: ボタンを押すとファンクッションチェックモードの TOP 階層に戻る。 (3) Press the button to return to the top level of the function check mode. DN-S1200...
  • Page 15 L から - ∞ dBFS の信号を出力する。 ⑨ 1kHz -6dBFS signals are output from the right channel. - ∞ dBFS signals are output from the left channel. ボタンを押すとファンクッションチェックモードの TOP 階層に戻る。 (3) Press the button to return to the top level of the function check mode. DN-S1200...
  • Page 16 (3) PARAMETERS ノブを押すと、表示されているモードの MIDI コマンドを USB-MIDI で送信する。 (3) When the PARAMETERS knob is pressed, the MIDI command for the currently displayed mode is transmitted in the USB-MIDI (4) USB MIDI モードを終了する場合は、電源を OFF にする。 mode. (4) To end the USB MIDI mode, turn the power off. DN-S1200...
  • Page 17 (2) When the PARAMETERS knob is turned, the display on the lower tier of the VFD segment display section switches in the "OK" or "Cancel". (3) "OK" を表示させ、PARAMETERS ノブを押して書き込みを開始する。VFD のセグメント表示部に以下の文字が表示される。 (3) Display "OK", then press the PARAMETERS knob to start loading.The following appears on the lower tier of the VFD segment display section: ‘ ‘ DN-S1200...
  • Page 18 (3) With ① to ⑮ selected, press the DISC EJECT/Playlist button to eject the disc, then reload the disc for readjust the servo. (5) 自動調整が終了すると、CD インジケータが点灯する。 (4) Press the button to return to the top level of the CD Drive check mode. (5) When automatic adjustment is completed, the CD indicator lights. DN-S1200...
  • Page 19 PARAMETERS knob is pressed again at this time, all the data is cleared. Turn the PARAMETERS knob to cancel. "Error_Clear?" を表示する。さらに PARAMETERS ノブを押すと、全データを消去し、パラメータノブを回すとキャンセルす る。 (4) Refer to [4.10. error code table] for details of the error code. (4) エラーコードの内容は、 「4.10. ヒートランモード」を参照。 DN-S1200...
  • Page 20 (6) When there is an error, The following appears on the VFD segment display section: (6) エラーが起きた場合、VFD のセグメント表示部下段に以下の文字を表示する。 (YY:Track number, XXXXX: , E***:Error code) Operation count (YY:トラック番号、XXXXX:動作回数、E***:エラーコード) (7) To end the Heat Run1 mode, turn the power off. (7) ヒートランモード 1 を終了する場合は、電源を OFF にする。 DN-S1200...
  • Page 21 MP3 decoding error EF10 データ読込中に SSI がアイドル状態に戻った EF10 SSI returned to idle status during data reading EF11 SSI アンダーフロー発生 EF11 SSI underflow occurred EF12 SSI オーバーフロー発生 EF12 SSI overflow occurred EF20 データ読込時、リンク処理に失敗 EF20 Failure in link processing when reading data DN-S1200...
  • Page 22 フェーダ値 最大 1018 以上、最小 3 以下 Fader value MAX 1018 or more, MIN 3 or less フェーダのクリック点センタータップ値 : センタータップ値± 25 Central click position Central tap value ± 25 センタータップ値 : 435 ∼ 589 Central tap value 435 ∼ 589 DN-S1200...
  • Page 23 (5) If no touch is detected in 1 second, the count is reset using the average of the values of 4 touches each 250 msec within that second as the reference value. (6) Press button to return to the top level of the touch measurement mode. DN-S1200...
  • Page 24 ---MEMO--- DN-S1200...
  • Page 25 0xBn 0x51 Control change 1480Pulse/cycle slow->fast relative data Increment 0x00 Parameters KNOB 0x54 Decrement 0x7F Increment/Decrement mmll :14bit data 0x0000(min) 37 Pitch Slider 0xEn 0xll LSB) 0xmm MSB) Pitch bend change ->0x4000(middle) ->0x7F7F(max) n=MIDI CH = 0 to F DN-S1200...
  • Page 26 16 REVERSE 0x3A MIDI command items Message type Notes Command Number Value ON TRG : 0x4A 0xBn OFF TRG : 0x4B Control Change Blink ON TRG : 0x4C 1 Pitch slider request 0xBn 0x4A 0x3C Control Change return pitch slider DN-S1200...
  • Page 27 50 Segment 2-5 LSB 0x32 51 Segment 2-6 LSB 0x33 52 Segment 2-7 LSB 0x34 53 Segment 2-8 LSB 0x35 54 Segment 2-9 LSB 0x36 55 Segment 2-10 LSB 0x37 56 Segment 2-11 LSB 0x38 57 Segment 2-12 LSB 0x39 DN-S1200...
  • Page 28 57 Scratch Position 28 only Use 0x4D/0x4E 0x3D 58 Scratch Position 29 only Use 0x4D/0x4E 0x3E 59 Scratch Position 30 only Use 0x4D/0x4E 0x3F 60 Scratch Position 31 only Use 0x4D/0x4E 0x40 61 Scratch Position 32(Top) only Use 0x4D/0x4E 0x41 DN-S1200...
  • Page 29 F Font codes for segments ( セグメントのフォントコード ). ※ For the Reflex function operations corresponding to the above MIDI commands, refer to the Reflex manual. ※ 以上の MIDI コマンドに対する Reflex の機能動作は Reflex のマニュアルを参照。 ※ 本機は ASCII 文字コード(0x20 ∼ 0x7E)で定義される。 ※ 一部の Latin 文字(ISO-8859-1)が表示できる。 DN-S1200...
  • Page 30 --MEMO-- DN-S1200...
  • Page 31 When the file for updating the firmware is abnormal. y バージョンアップエラーメッセージ画面 2 When the file for updatin the firmware is old version. バージョンアップ用ファイルに異常があった場合に表示されます。 ファイルが古い場合に表示されます。 uThe screen of virsion up error message 3 This is displayed if the error appears during version updating. u バージョンアップエラーメッセージ画面3 バージョンアップ中のエラーメッセージです。 DN-S1200...
  • Page 32 バージョンアップエラーメッセージ画面1 This is displayed if the error in communication with the AVR microprocessor has occurred. AVR マイコンとの通信にエラーが発生した場合に表示されます。 yThe screen of virsion up error message 2 y バージョンアップエラーメッセージ画面 2 This is displayed if the error appears during version updating バージョンアップ中のエラーに表示されます。 DN-S1200...
  • Page 33: Trouble Shooting

    Is the voltage of -9V or less supplied to Check D810 and the periphery circuit, and replace it いいえ TR814のコレクタ端子に-9V以下の電圧が供給されて D810と周辺回路をチェックし、不良部品を交換。 Corrector terminal of TR814? if defective. いるか? はい Check TR814 and the periphery circuit, and replace it TR814と周辺回路をチェックし、不良部品を交換。 if defective. DN-S1200...
  • Page 34 Are the filament voltage supplied between 1, 2, 3pins はい and 42, 43, 44pins of the fluorescent display tube Check the F1/F2 line and service it if defective. FL701を交換。 (FL701)? And the +5V voltage applied between these pins and GND? Replace the fluorescent display tube(FL701). DN-S1200...
  • Page 35 Is 11pin of CY111 (MUTE control signal)H, and has Check TR806 and the periphery circuit, and service it if IC804の7pin、1pinからJK801までの周辺回路を been the TR806 collector (MUTE drive signal) L(-9V)? defective. 確認し、不良部品を交換。  Check periphery circuit from 7pin and 1pin to JK801 of IC804, and it if defective. replace DN-S1200...
  • Page 36 BLOCK DIAGRAM DN-S1200...
  • Page 37 LEVEL DIAGRAM OUTPUT Audio SH7263 PCM178 +6.0dBV +2.78dBV 0dBFS GAIN=3.22dB GAIN=2.78dB -92dBV -95.22dBV 16bit:SNR=98dB -100dBV -100 -103.22dBV PCM1781:SNR=106dB(typ) -120 -130 -140 -150 DN-S1200...
  • Page 38 --MEMO-- DN-S1200...
  • Page 39 SEMICONDUCTORS Only major semiconductors are shown, general semiconductors etc. are omitted to list. 主な半導体を記載しています。汎用の半導体は記載を省略しています。 1. IC’s R5S72630P200FP (IC104) DN-S1200...
  • Page 40 R5S72630P200FP Block Diagram DN-S1200...
  • Page 41 USB_/FLG (Interrupt port) (IRQ0:usable)(Normal=H, detect=L) PVSS PVSS GND for I/O Digital GND General-purpose port PE5, IRQ1 CPU_DSP1 ADSP connection General-purpose I/O (Interrupt port) PVCC PVCC Power supply for I/O Digital +3.3V RxD2 SCIF Rx Memo Terminal (Memo Link Rx) DN-S1200...
  • Page 42 Power supply for in Digital +1.2V PF30 PF30 General-purpose port OPEN Digital GND PVSS PVSS GND for I/O Digital GND AUDIO_X1 AUDIO_X1 Not used AUDIO_X2 AUDIO_X2 Not used OPEN PVCC PVCC Power supply for I/O Digital +3.3V PF26 PF26 General-purpose port OPEN DN-S1200...
  • Page 43 GND for I/O Digital GND PD11 DISKO_DET General-purpose port CD Disk Out detection output (detect=L) PVCC PVCC Power supply for I/O Digital +3.3V PD10 SCK1 General-purpose port Deck1 cereal clock output JOG1 Deck1 ExOR input Input for pulse width capture DN-S1200...
  • Page 44 SDRAM/FLASH D2 SHDB1 SDRAM/FLASH D1 SHDB0 SDRAM/FLASH D0 PVSS PVSS GND for I/O Digital GND PVCC PVCC Power supply for I/O Digital +3.3V RD/WR SHRW RD/WR SDRAM /WE Clock is enable SDRAM CKE PC11 MEAS General-purpose port B6TS mode setup(H:measure/L:setup) DN-S1200...
  • Page 45 B6TS-04 Cereal chip select output General-purpose port OPEN PB5/MOSI PS2TX General-purpose port Cereal data input PB6/MISO AVRINT General-purpose port Device interrupt output PB7/SCK BOOTCLK General-purpose port Cereal clock Power supply for in Digital +3.3V PS2RST RESET CPU RESET PS2TX USART Cereal output DN-S1200...
  • Page 46 Alternate clock input (3.3-V LVCMOS Input) •••16.934MHz TMS-A Test Mode Select CVDD 1.2V /TRST TRST Test Reset OSCVSS Connect VSS OSCIN Connect VSS OSCOUT Open OSCVDD Connect CVDD(1.2V) PLLHV PLL 3.3-V Supply Input (requires external filter) TDI_A Test Data In DN-S1200...
  • Page 47 AEMB1 SDRAM Bank Address and Asynchronous Memory Low-Order Address EM_BA[0] AEMB0 SDRAM Bank Address and Asynchronous Memory Low-Order Address EM_CS[0] ASDCE SDRAM Chip Select EM_RAS ASDRAS SDRAM Row Address Strobe EM_CS[2] Asynchronous Memory Chip Select CVDD 1.2V EM_RW Open DN-S1200...
  • Page 48 1.2V GPIO Not use GPIO Not use DVDD DVDD 3.3V GPIO Not use AXR2[0] SPDIF OUT SPDIF output GPIO Not use GPIO Not use ACLKX0 DABCK Audio Serial BCK output GPIO Not use AFSX0 DALRCK Audio Serial LRCK output DN-S1200...
  • Page 49 BD7956FS-E2 (IC302) BD7956FS BD7956FS-E2 Block Diagram DN-S1200...
  • Page 50 Separated power from Vcc, used for output buffers to 3, 9, 43, 49 VccQ for I/O Buffer improve noise. Ground for I/O Separated power from Vss, used for output buffers to 6, 12, 46, 52 VssQ Buffer improve noise. 36, 40 No Connection No Connection DN-S1200...
  • Page 51 CH1B OUT2 OUT5 6 DATA TEST2 CH2A OUT3 OUT4 SETUP CH2B 7 BCK CH3B CH3A 8 LRCK TEST TS3USB221RSER (IC404) GP1A038RBK (IC703) 10kΩ 10kΩ 1 Anode Cathode Vcc=2.7 to 5.5V BD9130NV-E2 (IC403) BD9130 1PIN MARK 1 2 3 4 DN-S1200...
  • Page 52 2. VFD MODULE 17-BT-30GINK (FL701) CGROM code table DN-S1200...
  • Page 53 PRINTED WIRING BOARDS GU-3873 MAIN P.W.B. UNIT(1/2) COMPONENT SIDE DN-S1200...
  • Page 54 GU-3873 MAIN P.W.B. UNIT(2/2) FOIL SIDE DN-S1200...
  • Page 55 GU-3874 POWER P.W.B. UNIT(1/2) COMPONENT SIDE DN-S1200...
  • Page 56 GU-3874 POWER P.W.B. UNIT(2/2) FOIL SIDE DN-S1200...
  • Page 57 GU-3884 PANEL P.W.B. UNIT(1/2) COMPONENT SIDE DN-S1200...
  • Page 58 GU-3863 PANEL P.W.B. UNIT(2/2) FOIL SIDE DN-S1200...
  • Page 59 Indicates number of zeros after effective number. 2-digit effective number. Units: pF. 220pF (0 or 1) Indicates number of zeros after effective number. 2-digit effective number. Units: pF. When the dielectric strength is indicated in AC, "AC" is included after the dieelectric strength value. DN-S1200...
  • Page 60 TR408-410 00D2690082902 DTC114EKT96 TR411,412 00D2690083901 DTA114EKT96 D101, 102 00D2760559909 DAP202KT146 D103 00D2760560901 DAN202KT146 D401 00D2760559909 DAP202KT146 D402 00D2760858901 HZM6.2Z4MWA D403 00D2760560901 DAN202KT146 D404 00D2760858901 HZM6.2Z4MWA D405 00D2760559909 DAP202KT146 D406 00D2760560901 DAN202KT146 RESISTORS GROUP R153 RM73B--562FT R419 RM73B--752FT R423 RM73B--562FT DN-S1200...
  • Page 61 CK73B1A104KT +1005 C303 00D2574012920 CE67C1C470MT (RV2) +REF C304 CK73B1A104KT +1005 C305 00D2544655922 CE67C0J470MT (RV2) +REF C306,307 CK73B1H103KT (1608) +1608 C309 00D2574012920 CE67C1C470MT (RV2) +REF C310 00D2544656947 CE67C1A101MT (RV2) C311 CK73B1E104KT +1608 C312 00D2544656947 CE67C1A101MT (RV2) C313 00D2574012917 CE67C1C220MT (RV2) +REF DN-S1200...
  • Page 62 00D2544655906 CE67C0J220MT (RV2) +REF C422 CK73F1E104ZT +1608 C423 00D2544655922 CE67C0J470MT (RV2) +REF C424 CK73B1E104KT +1608 C425 CK73F1H103ZT +1608 C426 CK73B1E104KT +1608 C427 00D2544655906 CE67C0J220MT (RV2) +REF C428 CK73B1E104KT +1608 C429 00D2574012920 CE67C1C470MT (RV2) +REF C430 CK73B1A474KT C431 CK73B1E104KT +1608 DN-S1200...
  • Page 63 CHIP BEADS(18PG121) +1608 FB305,306 00D2350158901 CHIP BEADS(18PG121) +1608 FB401 00D2350147909 E.FIL(BLM21PG221SN1)+2125 FB402,403 00D2350158901 CHIP BEADS(18PG121) +1608 FB501-504 00D2350158901 CHIP BEADS(18PG121) +1608 JK401 00D2048416007 MINI JACK L401 00D2350183905 INDUCTOR 2.2UH(7E06N W401 00D2051034007 M3 SCREW TERMINAL X101 00D3991051903 X-TAL(16.9344/HC-49) X102 00D3991127905 FCX-03(48MHz) DN-S1200...
  • Page 64 D817 204750006501S F1J10C ZD801,802 00D2760683914 UDZS9.1B-TE17 ZD803 00D2760683930 UDZS5.1B-TE17 ZD901 00D2760683901 UDZS5.6B-TE17 ZD902 00D2760762945 MTZJ36B T77 ZD903 00D2760760976 MTZJ6.8B T77 RESISTORS GROUP R804 00D2472020962 RM73B--153FT +1608 R806 00D2472035915 RM73B--152DT(1608) R864 00D2442684901 RS14B3D473JNBST(S) R869 00D2472020933 RM73B--103FT +1608 R874 00D2442682945 RS14B3D2R2JNBST(S) DN-S1200...
  • Page 65 C860 CK73B1E104KT +1608 C861 CK73F1E104ZT +1608 C862 CK73F1H103ZT +1608 C863 CK73F1E104ZT +1608 C864 CK73F1H103ZT +1608 C903 00D2538022707 CK45F2EAC103MC C906 00D2568038004 CF99--2EAC104M C907,908 00D2538029713 CK45F2EAC471KC(KX) C909 00D2544710919 CE04W1C121MT F11(KY) C910 CK73B1E104KT +1608 C911 00D2544759909 CE04W1H100MT E11(KY) C912,913 00D2570037909 CK73B1E105KT +2125 DN-S1200...
  • Page 66 00D2350157009 PLA10AN7720R7D2B L902 00D2350159007 PLH10AN3711ROP2B L903 115010005508S ELC0607RA-220K1R2-PF L904 115010006501S ELC0607RA-330KR92-PF L905 111810003502S NLCV32T-220J-PF S901 00D2121030009 POWER SWITCH (TV-5) T801 102010003001P ST-3790C3 W901 M3 SCREW TERMINAL 0RD4713303016 3X6 CBS-Z 8W5441006500P FUSE LABEL SUB ASSY (1.6A) 5X23mm F901, for JP DN-S1200...
  • Page 67 SLR-325MC (GRN) TAPE LD736 00D3939606909 SEL6927A(TP5) LD737 00D3939633008 SELU1250CM(RED) FL701 00D3938096002 17-BT-30GINK(VFD) RESISTORS GROUP VR702 00D2115648119 SLIDE VOLUME (100MM) CAPACITORS GROUP C701-703 CK73F1E104ZT +1608 C704 00D2544302974 CE04W1A101MT(SRE) C705 CK73F1H103ZT +1608 C706,707 CK73F1E104ZT +1608 C708 CK73F1H103ZT +1608 C709 CK73F1E104ZT +1608 DN-S1200...
  • Page 68 CHIP BEADS(18PG121) +1608 S701-704 00D2125604907 TACT SWITCH-TA(ALPS) S705 00D2120410002 ROTARY ENCODER-JOG S706-710 00D2125604907 TACT SWITCH-TA(ALPS) S712-715 00D2125604907 TACT SWITCH-TA(ALPS) S717-719 00D2125604907 TACT SWITCH-TA(ALPS) S721-725 00D2125604907 TACT SWITCH-TA(ALPS) S727 00D2125604907 TACT SWITCH-TA(ALPS) S729 00D2125604907 TACT SWITCH-TA(ALPS) S731-734 00D2125604907 TACT SWITCH-TA(ALPS) DN-S1200...
  • Page 69 ---MEMO--- DN-S1200...
  • Page 70 EXPLODED VIEW WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacturer.  印の部分は安全を維持するために重要 な部品です。従って交換時は必ず指定の 部品を使用してください。 DN-S1200...
  • Page 71 BUSH 00D4412038006 SPACER GND 00D4220688101 SHAFT 00D4210838013 WHEEL ASSY (2) 00D4210836002 SCALE DISC 00D4412025006 WHEEL BRACKET 00D4210866001 WEIGHT 00D4412040007 BRACKET(SENSOR) 00D1132135101 RUBBER KEY 1 00D1132136100 RUBBER KEY 2 00D1132137002 RUBBER KEY 3 00D4412039005 STAY GND 00D1462535109 FRONT SUB PANEL DN-S1200...
  • Page 72 2.6X8 CBTS (P)-Z 0RD4713205017 2.6X10 CBS 3X6 CBS-Z ★ 112 3X6 CBS-B 0RD4737500044 3X8 CBTS (P)-B 00M51042605U0 SCREW 00M51971704U0 SCREW 0RD4770330103 8 N-Z 00D4756163006 9 SP NUT 0RD4761003009 3 E RING 0RD4751161016 WASHER 0RD4751130005 3 WASHER 00M53110301A9 M3 NUT 00M54040302A0 SCREW ★ 123 DN-S1200...
  • Page 73 Fold as shown on the diagram. 図のように折る。 White surface 白面 Printed surface 印刷面 (2) 606050030008P 11P FFC(1.0) L=88 Place fold against the reinforcement plate. 補強板に合わせる。 Fold as shown on the diagram. Fold inward 図のように折る。 谷折り White surface 白面 Printed surface 印刷面 DN-S1200...
  • Page 74 Fold as shown on the diagram. 図のように折る。 White surface 白面 Printed surface 印刷面 (4) 606050029008P 27P FFC(1.0) L=252 260mm 140mm 100mm 175mm 240mm Fold outward Fold as shown on the diagram. 山折り 図のように折る。 Fold inward 谷折り Printed surface 印刷面 White surface 白面 DN-S1200...
  • Page 75 00D5031565001 CUSHION 1 00D5031566000 CUSHION 2 00D5012391100 CARTON CASE CONT.CARD(L)SUB ASSY E2/E3/E2C ★ 210 BAR CODE LABEL ASSY E3,E2 ★ 211 998545000040D POS LABEL ★ 211 8W5441006400P RECYCLING LABEL ★ 212 NO. SHEET ★ 213 CARTON LABEL(C) ★ 214 CARD ★ 215 RECYCLE MARK CARTON ★ 216 DN-S1200...
  • Page 76 ---MEMO- DN-S1200...
  • Page 77 WIRING DIAGRAM DN-S1200...
  • Page 78 --MEMO-- DN-S1200...
  • Page 79 • When RF1 waveform is noisy or cannot discriminate the ・ RF1 波形がノイズで不明瞭、またはアイパターンが識 eye-pattern, replace the Mecha Unit after measuring 別不能の場合はメカユニットを交換してください。 the lop. ・ ポイント①∼⑬は、下図のように特定テストポイント • ① ~ ⑬ points have the certain test points shown below. 付きです。 GU-3873 MAIN UNIT DN-S1200...
  • Page 80 DN-S1200...
  • Page 81 Pause→Track Up (Traverse) ②LDIN ⑪SDOUT [2VDC] [2VDC] ③LDO+ ⑫FEEDMT+ [2VAC] [0.5VAC] ④LDO- ⑬FEEDMT- [2VAC] [0.5VAC] [400 S] [40 S] CD Load→Pause Pause→Track Down (Traverse) (Focus) ⑪CLVOUT ⑤FDOUT [2VDC] [2VDC] ⑥F+ ⑫FEEDMT+ [1VAC] [0.5VAC] ⑦F- ⑬FEEDMT- [1VAC] [0.5VAC] [40 S] [1S] DN-S1200...
  • Page 82 NOTICE: ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASURED AT NO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. DN-S1200...
  • Page 83 SCHEMATIC DIAGRAMS (1/6) GU-3873 MAIN UNIT (1/4) DN-S1200...
  • Page 84 SCHEMATIC DIAGRAMS (2/6) GU-3873 MAIN UNIT (2/4) DN-S1200...
  • Page 85 SCHEMATIC DIAGRAMS (3/6) GU-3873 MAIN UNIT (3/4) DN-S1200...
  • Page 86 SCHEMATIC DIAGRAMS (4/6) GU-3873 MAIN UNIT (4/4) DN-S1200...
  • Page 87 SCHEMATIC DIAGRAMS (5/6) GU-3874-1 POWER UNIT GU-3874-2 AC INPUT UNIT DN-S1200...
  • Page 88 SCHEMATIC DIAGRAMS (6/6) GU-3884-1 PANEL UNIT GU-3884-2 DISC UNIT GU-3884-3 SENSOR UNIT GU-3884-4 SLIDE VR UNIT DN-S1200 GU-3884-5 LED UNIT...

Table of Contents