Page 1
Ver. 2 Please refer to the MODIFICATION NOTICE. SERVICE MANUAL MODEL E2A E1C E1K EUT DN-HD2500 PROFESSIONAL MEDIA PLAYER & CONTROLLER 注 意 サービスをおこなう前に、このサービスマニュアルを 必ずお読みください。本機は、火災、感電、けがなど に対する安全性を確保するために、さまざまな配慮を おこなっており、また法的には「電気用品安全法」に もとづき、所定の許可を得て製造されております。 従ってサービスをおこなう際は、これらの安全性が維 持されるよう、このサービスマニュアルに記載されて いる注意事項を必ずお守りください。 For purposes of improvement, specifications and ● 本機の仕様は性能改良のため、予告なく変更すること ● design are subject to change without notice.
DN-HD2500 SAFETY PRECAUTIONS The following check should be performed for the continued protection of the customer and service technician. LEAKAGE CURRENT CHECK Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check.
Page 3
DN-HD2500 DISASSEMBLY (Follow the procedure below in reverse order when reassembling.) 1. Top Panel Unit (1) Remove 10 side screws with washer and pull up the Top Panel Unit. Top Panel Unit (2) After pull up the Top Panel Unit, turn the back forward and then pull out the three FFC cable showed in the below drawing.
DN-HD2500 2. LCD MODULE (1) Draw out the LCD slowly in the direction of the arrow until just before the FFC touches the rib. Note : The FFC could be damaged if it bangs against the rib. (2) Slowly remove upwards, being careful that the FFC does not touch the rib.
ON にします。 「DENON DJ」 が表示されるまで ETERS knob and B ( ) button until PARAMETERS ノブと B( ) ボタンを押し続 "DENON DJ" is displayed. When the service けます。サービスモードになると、サービス mode is set, the service mode's top menu モードの TOP 画面が表示されます。 appears. ・ Deck1 または Deck2 の PARAMETERS ノブを回...
Page 6
PARAMETERS knob to set “HD2500_Init” HD2500_Init を選択し、PARAMETERS ノブを mode. 押して確定します。 ・The contents of the preset memory are set to ・プリセットメモリの内容を工場出荷状態にし the factory defaults. For details on the preset memory, see the DN-HD2500's Instruction ます。 プリセットメモリの詳細は、 DN-HD2500 HD2500_Init Manual. の取り扱い説明書を参照して下さい。 The checked contents and HD2500_Init ・...
Page 7
DN-HD2500 Mode Operation and Function Display モード 操 作 と 機 能 表 示 Not yet used. Nothing happens when this is 未対応です。選択しても何も実行しません。 selected. ・Deck1 または Deck2 の PARAMETERS ノブを 回わして、FUNCTION チェックモード画面か ら RAM_Check を選択し、PARAMETERS ノブ を押して確定します。 ・RAM の固定アドレスのリード/ライトチェッ クを行います。 RAM の固定アドレスのリード / ライト RAM_Check RAM_Check チェックを行います。...
Page 8
DN-HD2500 Mode Operation and Function Display モード 操 作 と 機 能 表 示 ・ Turn the Deck1 or Deck2 PARAMETERS knob ・ Deck1 または Deck2 の PARAMETERS ノブを回 to select "HDD_Format" from the FUNCTION わして、FUNCTION チェックモード画面から check mode's top menu, then press the HDD_Format を選択し、PARAMETERS ノブを...
Page 9
DN-HD2500 Mode Operation and Function Display モード 操 作 と 機 能 表 示 Not yet used. Nothing happens when this is 未対応です。選択しても何も実行しません。 selected. ・ Deck1 または Deck2 の PARAMETERS ノブを回 わして、FUNCTION チェックモード画面から Audio_OSC を選択し、PARAMETERS ノブを押 して確定します。 LINE OUT1/2 端子にテスト信号を出力します。 RAM の固定アドレスのリード / ライト Audio_OSC Audio_OSC mode チェックを行います。...
Page 10
DN-HD2500 Mode Operation and Function Display モード 操 作 と 機 能 表 示 ・ Turn the Deck1 or Deck2 PARAMETERS knob ・ Deck1 または Deck2 の PARAMETERS ノブを回 to select "TOUCH_Init" from the FUNCTION わして、FUNCTION チェックモード画面から check mode's top menu, then press the TOUCH_Init を選択し、 PARAMETERS ノブを押...
Page 11
DN-HD2500 Mode Operation and Function Display モード 操 作 と 機 能 表 示 ・ Turn the Deck1 or Deck2 PARAMETERS knob ・ Deck1 または Deck2 の PARAMETERS ノブを回 to select "Heat_Run" from the FUNCTION わして、FUNCTION チェックモード画面から check mode's top menu, then press the Heat_Run を選択し、 PARAMETERS ノブを押し...
Page 12
DN-HD2500 Mode Operation and Function Display モード 操 作 と 機 能 表 示 ・The names of the files that can be played are ・DecK1 の画面に再生できるファイル名が表示 displayed on the Deck1 screen. されます。 ・Turn the Deck1 PARAMETERS knob to select ・ PARAMETERSノブを回してファイルを選択し、 the file, then press the PARAMETERS knob to PARAMETERS ノブを押して確定します。 ...
Page 13
DN-HD2500 Mode Operation and Function Display モード 操 作 と 機 能 表 示 ・ Turn the Deck1 or Deck2 PARAMETERS knob ・ Deck1 または Deck2 の PARAMETERS ノブを回 to select "DECK1 SW CHK" from the service わして、 サービスモードのTOP画面からDECK1 mode's top menu, then press the PARAME- SW CHK を選択し、PARAMETERS ノブを押し...
Page 14
DN-HD2500 Mode Operation and Function Display モード 操 作 と 機 能 表 示 ・After “DECK1 SW CHK” mode completed, ・DECK1 SW CHK が終了後、PARAMETERS ノブ press any Deck1’s button other than the 以 外 の D E C K 1 の 任 意 の ボ タ ン を 押 す と、...
Page 15
DN-HD2500 Mode Operation and Function Display モード 操 作 と 機 能 表 示 ・Turn the Deck1 or Deck2 PARAMETERS knob ・ Deck1 または Deck2 の PARAMETERS ノブを回 to select "PANEL CHK" from the service わして、 サービスモードのTOP画面からPANEL mode's top menu, then press the PARAME- CHK を選択し、PARAMETERS ノブを押して確...
Page 16
DN-HD2500 Mode Operation and Function Display モード 操 作 と 機 能 表 示 5) TOUCH sensor ⑤タッチセンサ ・When the Deck1 or Deck2 SOURCE ・ Deck1 または Deck2 の SOURCE( ) ボ ) button is pressed, the touch count タンを押すとタッチカウント動作モード operation mode is set and the touch detec- となり、...
DN-HD2500 VERSION UPGRADE PROCEDURE OF FIRMWARE ファームウェアのバージョンアップ方法 Use the procedure described below to update the firmware to a newer version. ファームウェアをバージョンアップするときは、下記手順に従ってバージョンアップしてください。 モード 操 作 と 機 能 表 示 Mode Operation and Function Display ・バージョンアップ用ファイル(ファイル名: ・Store the file (file name : HD2500.BIN) for updating the firmware in the root directory of HD2500.BIN)を内蔵...
Page 18
DN-HD2500 Mode Operation and Function Display モード 操 作 と 機 能 表 示 ・Once firmware updating is completed, turn off ・バージョンアップが終了したら電源を OFF に the power. します。 ・This is displayed if there is no file for updating ・指定されたデバイスにバージョンアップ用 the firmware on the specified device or if the ファイルがない場合、...
DN-HD2500 BLOCK DIAGRAM AC IN ● Power Power +3.3V GND0 Main Main +1.2V X'tal +1.2V CY081 CW081 12MHz +1.2V CS1/ IRQ3/ DMA1 DND REMOTE 8PMINI TRANS AC SW DC-DC +3.3V ● +3.3V CX141 SH7206 FLAG Power SW R5S72060200FPV 14pin AC-DC...
Page 21
DN-HD2500 SEMICONDUCTORS Only major semiconductors are shown, general semiconductors etc. are omitted to list. 主な半導体を記載しています。汎用の半導体は記載を省略しています。 1. IC’s D710E001ZDH300 (IC501) D710E001ZDH300 Block Diagram Program/Data JTAG EMU 256K Bytes McASP0 Data 16 Serializers Program/Data C67x+ CPU ROM Page1 256K Bytes Memory Data...
Page 23
DN-HD2500 D710E001ZDH300 Terminal Function Pin No. Pin Name Symbol Function D_GND DVDH I/O supply (+3.3V) AFSX0 DALRCK ACLKX0 McASPO transmit bit clock ACLKR0 AXR0[14] BSPDIF D_GND AXR0[11] AXR0[9] D_GND AEMXA1 AXR0[4] AXR0[2] AXR0[0] DATA_A DVDH I/O supply (+3.3V) D_GND DVDH I/O supply (+3.3V)
Page 24
DN-HD2500 Pin No. Pin Name Symbol Function ACLKX1 McASP1 transmit bit clock Not used DVDH I/O supply (+3.3V) D_GND CVDL Core supply (+1.2V) CVDL Core supply (+1.2V) CVDL Core supply (+1.2V) CVDL Core supply (+1.2V) CVDL Core supply (+1.2V) CVDL Core supply (+1.2V)
Page 25
DN-HD2500 Pin No. Pin Name Symbol Function CVDL Core supply (+1.2V) D_GND D_GND D_GND D_GND D_GND D_GND CVDL Core supply (+1.2V) SHDB15 CPU bus data 15 DVDH I/O supply (+3.3V) AEMA1 External memory bus address 1 AEMA0 External memory bus address 0...
Page 26
DN-HD2500 Pin No. Pin Name Symbol Function AEMD30 External memory bus data 30 AEMD29 External memory bus data 29 AEMD27 External memory bus data 27 AEMD25 External memory bus data 25 DVDH I/O supply (+3.3V) SHDB5 CPU bus data 5...
Page 27
DN-HD2500 EP2C5Q208C8N (IC103) EP2C5Q208C8N Terminal Function Pin No Pin name Function SH_DB27 32 bits data bus (CPU) SH_DB28 32 bits data bus (CPU) SH_DB29 32 bits data bus (CPU) SH_DB30 32 bits data bus (CPU) SH_DB31 32 bits data bus (CPU)
Page 28
DN-HD2500 Pin No Pin name Function IDE_RST IDE reset signal output LCD_D3 LCD data LCD_D2 LCD data VCCIO1 VCCIO1 LCD_D1 LCD data LCD_D0 LCD data LCD_DISP LCD ON/_OFF control signal LCD_CL2 LCD shift clock LCD_CL1 LCD latch clock LCD_FLM LCD frame clock...
Page 29
DN-HD2500 Pin No Pin name Function MEAS B6TS measurement mode setting signal (PANEL 1, 2 is common) SETUP B6TS operating mode change signal (PANEL 1, 2 is common) OCHG_2 PANEL 2: B6TS input 0 / CHG signal output VCCIO3 VCCIO3...
Page 30
DN-HD2500 Pin No Pin name Function SH_DB14 32 bits data bus (CPU) SH_DB15 32 bits data bus (CPU) SH_DB16 32 bits data bus (CPU) VCCINT VCCINT SH_DB17 32 bits data bus (CPU) SH_DB18 32 bits data bus (CPU) SH_DB19 32 bits data bus (CPU)
Page 32
DN-HD2500 SH72060W200FPV Block Diagram SH-2A CPU core CPU instruction fetch bus (F bus) CPU bus (C bus) CPU memory access bus (M bus) (I clock) Instruction Operand User break Cache On-chip RAM UBCTRG output cache memory cache memory controller controller...
Page 33
DN-HD2500 SH72060W200FPV Terminal Function Pin No. Pin Name Symbol Function SHRD External device read enable signal RD/-WR SHRW External device read/write enable signal PVss D_GND SHA1 Address bus SHA2 Address bus SHA3 Address bus SHA4 Address bus SHA5 Address bus...
Page 34
DN-HD2500 Pin No. Pin Name Symbol Function PE13 AMUTE Analog MUTE -CS0 External memory chip select 0 -CS1 External memory chip select 1 SCK2 CFGCLK Serial clock output (FPGA CFG CLK) DREQ3 DREQ3 Not used PINT7 PINT7 Not used HIICDAT...
Page 35
DN-HD2500 Pin No. Pin Name Symbol Function PVss D_GND ..SHDB22 Data bus 22 ..SHDB21 Data bus 21 ..SHDB20 Data bus 20 ..SHDB19 Data bus 19 ..SHDB18 Data bus 18 ..SHDB17 Data bus 17 ..SHDB16 Data bus 16 ..SHDB15 Data bus 15 ..SHDB14...
Page 36
DN-HD2500 ISP1761BE (IC403) pin 1 index Block Diagram CC(I/O) 10, 40, 48, 59, 67, 37 to 39, 41 to 43, 75, 83, 94, 104, 115 45 to 47, 49, 51, 52, 54, 56 to 58, 60 to 62, 64 to 66,...
DN-HD2500 NOTE FOR PARTS LIST 部品表について • Part indicated with the mark "nsp" are not always in stock and possibly to 1.nsp 印の部品は常時在庫していませんので供給に長時間を要すること take a long period of time for supplying, or in some case supplying of part があります。 may be refused.
DN-HD2500 PARTS LIST OF P.W.B. UNIT *本表に記載されている部品は、補修用部品のため製品に使用している部品とは一部、形状、寸法などが異なる場合があります。 * The parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions. * "nsp" 印の部品は常時在庫していませんので供給に長時間を要することがあります。場合によっては、供給をお断りする場合があります。 * Part indicated with the mark “nsp” are not always in stock and possibly to take a long period of time for supplying, or in some case supplying of part may be refused.
DN-HD2500 EXPLODED VIEW WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacturer. 印の部分は安全を維持するために重要 な部品です。従って交換時は必ず指定の 部品を使用してください。...
DN-HD2500 ASSEMBLY NOTE Mounting the rubber buttons BUTTON A : Ref. No. 43 BUTTON B : Ref No. 44 Use the buttons tagged “B” on the Use the buttons tagged “A” on the side of the panel with the “B” stamp.
Page 58
DN-HD2500 Mounting the JOG DISC (1) Mount SLIP MAT (B) on the JOG WHEEL SUB ASSY. SLIP MAT (B) : Ref No. 60 (The slip mat has no specific front or rear side.) JOG WHEEL SUB ASSY : Ref No. 64 (2) Next mount SLIP MAT (E).
Page 59
DN-HD2500 (5) Next mount SLIP MAT (B). SLIP MAT (B) : Ref No. 60 (The slip mat has no specific front or rear side.) (6) Turn over, being careful that the piled slip mats do not fall, and set on the main unit.
Page 60
DN-HD2500 Folding the FFC (1) GU-3778-1 PANEL UNIT1 (00D 009 0290 008 : 23P FFC(1.0) L=250) 00D 009 0290 008 : 23P FFC(1.0) L=250 Printed surface Approx. 90mm Approx. 50mm White surface Printed surface Fold as shown on the diagram.
Page 61
DN-HD2500 (2) GU-3778-2 PANEL UNIT2 (00D 009 0290 008 : 23P FFC(1.0) L=250 ) 00D 009 0290 008 : 23P FFC(1.0) L=250 Printed surface Approx. 90mm Approx. 50mm White surface Printed surface Fold as shown on the diagram. White surface...
Page 62
DN-HD2500 (3) GU-3778-5 DISC UNIT1 / GU-3778-6 DISC UNIT2 (00D 009 0290 037 : 11P FFC(1.0) L=60) 00D 009 0290 037 : 11P FFC(1.0) L=60 White surface Fold inward Fold inward Fold outward Place fold against the reinforcement plate. White surface Fold inward Fold as shown on the diagram.
DN-HD2500 PARTS LIST OF EXPLODED VIEW *本表に記載されている部品は、補修用部品のため製品に使用している部品とは一部、形状、寸法などが異なる場合があります。 * The parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions. * "nsp" 印の部品は常時在庫していませんので供給に長時間を要することがあります。場合によっては、供給をお断りする場合があります。 * Part indicated with the mark “nsp” are not always in stock and possibly to take a long period of time for supplying, or in some case supplying of part may be refused.
DN-HD2500 PACKING VIEW PARTS LIST OF PACKING & ACCESSORIES *本表に記載されている部品は、補修用部品のため製品に使用している部品とは一部、形状、寸法などが異なる場合があります。 * The parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions. * "nsp" 印の部品は常時在庫していませんので供給に長時間を要することがあります。場合によっては、供給をお断りする場合があります。 * Part indicated with the mark “nsp” are not always in stock and possibly to take a long period of time for supplying, or in some case supplying of part may be refused.
DN-HD2500 NOTE FOR SCHEMATIC DIAGRAM 配線図について WARNING: ! 印の部品は安全を維持するために重要な部品です。 Parts marked with this symbol ! have critical characteristics. 従って交換時は必ず指定の部品を使用してください。 Use ONLY replacement parts recommended by the manufactur- 注) CAUTION: (1) 指定なき抵抗値は Ω、k は kΩ、M は MΩ を示す。 Before returning the unit to the customer, make sure you make µ...
Page 73
SCHEMATIC DIAGRAMS (7/7) DN-HD2500 SIGNAL LINE SCHEMATIC DIAGRAMS (7/7) GU-3782 POWER UNIT...
Page 74
DN-HD2500 DOCUMENTS FOR WEEE Details of Recycle parts for Main Unit * You have to remove the parts that marked “WEEE Mark ◆ ” when the recycling processing. (Europe model only) WEEE Ref. No. Part Name Material Q'ty Mark PANEL UNIT1 COMPLEX ◆...
Page 75
DN-HD2500 WEEE Ref. No. Part Name Material Q'ty Mark BUTTON 3 COMPLEX ◆ BUTTON 4 COMPLEX ◆ LCD INSULATOR 23P FFC(1.0) L=250 COMPLEX ◆ PROTECTION SHEET CORD HOLDER (L76) COMPLEX ◆ T. SENSOR BASE WHEEL ASSY (2) COMPLEX ◆ SCALE DISC...
Page 76
DN-HD2500 Exploded view of DN-HD2500 unit (Europe model) You have to remove the parts that marked “WEEE Mark ◆ “ when the recycling processing. (Europe model only)