Orion OPM-4250 User Manual page 36

OPM-4250 | OPM-4250R
*IDrange(Program):0x01(1)~0xFF(255)
*M/S:SinceitisonlyMaster,"0x01"Valuemustbetransmitted.
*CheckSum:Execute"Not"operationafteraddingallthevaluesin"STX~Data"area.
*ElapsedTime
-Hundredthousands,tenthousands,thousands,hundreds,tens,ones:0(0x00)~9(0x09)rangevalue.
- "Elapsed Time" Communication Sequence
*Waitfor500msecforresponseaftersendingthecommand.Ifthereisnoresponse,itisrecommendedtoresendthecommand.
*Itisrecommendedthatnotsendingtheothercommandorchanginginputresolutionduringcommandtransmission.
Elapsed Time Command transmission (to Master)
3.12. iP Serial number
- Command for assigning and identifying the serial numbers of each IP board. (8 digit)
CMD: 0x75 (Get S/N), 0x76 (Set S/N)
- Send to MPDP
STX CMD Length
Value 0x02 Variable 0x02
*IDrange(Program):0x01(1)~0xFF(255)
*M/S:Master(0x01),Slave(0x00)
* " Get/SetIPSerialNumber"(0x75/0x76)commandisnotapplicableas"Broad-cast"command,becauseeachPDPshouldhavean
uniqueserialnumber.
- Receive from MPDP
STX CMD Length
Value 0x02 Variable 0x0A Variable
0 1st
Variable Variable Variable
*IDrange(Program):0x01(1)~0xFF(255) 
*CheckSum:Execute"Not"operationafteraddingallthevaluesin"STX~Data"area.
*ElapsedTime
-0,1st,2nd,3rd,4th,5th,6th,7th:0(0x00)~9(0x09)rangevalue
- "Elapsed Time" Communication Sequence
*Waitfor500msecforresponseaftersendingthecommand.Ifthereisnoresponse,itisrecommendedtoresendthecommand.
*Itisrecommendedthatnotsendingtheothercommandorchanginginputresolutionduringcommandtransmission.
*TheserialnumbercanbesavedinanyoneofMasterorSlave.
Elapsed Time Command transmission
(to Master or Slave)
→
Elapsed Time Response transmission (from Master)
←
Data
ETX
ID M/S
Variable Variable 0x03
Data
Check
Sum
ID M/S Elapsed Time
Variable ... Variable
2nd 3rd 4th 5th 6th
Variable Variable Variable Variable Variable
*M/S:Master(0x01),Slave(0x00)
Elapsed Time Response transmission
→
←
(from Master or Slave)
- 68 -
3.13. Default Data Load (Picture Control Data)
- Initialize the PDP set. All the settings will be returned to the initial condition prior to the adjustment in the factory.
Pre-programmed value will be applied.
- It is available only on Power On (Operative) status.
- Since previous Picture Control Data will be lost with this command. High caution is required.
- Send to MPDP
A. NormalCommand
Value
*IDrange(Program):0x01(1)~0xFF(255)
*M/S:Master(0x01),Slave(0x00)
B. BroadcastCommand
Value
*MakeallPDP(Master/Slave)dothesameoperation.But,therewillbenoreturncommunication.(Onewaycommand)
- Receive from MPDP
Value
*IDrange(Program):0x01(1)~0xFF(255)
*M/S:Master(0x01),Slave(0x00)
*CheckSum:Execute"Not"operationafteraddingallthevaluesin"STX~Data"area.
ETX
- "Default Data Load" Communication Sequence
*Waitfor40msecforresponseaftersendingthecommand.Ifthereisnoresponse,itisrecommendedtoresendthecommand.
0x03
*Itisrecommendedthatnotsendingtheothercommandorchanginginputresolutionduringcommandtransmission.
*ExceptforBroadcastcommand
7th
Default Data Load Command transmission
3.14. BiC (Burn-in Compensation): Only Master
- BIC function helps reducing burn-in effect. Please refer to User manual for further explanation.
- It is available only on Power On (Operative) status.
- Send to MPDP
A. "Set"commandfrom"Get/Set"in"Data"area
Value
Infinitely Expandable
Data
STX CMD Length
ID
0x02 0x81 0x02 Variable
STX CMD Length Data: ID
0x02 0x81 0x01 Variable
Data
STX CMD Length
ID
0x02 0x81 0x02 Variable
Default Data Load Response transmission
→
←
(to Master or Slave)
STX CMD Length
ID M/S
0x02 0x6A 0x09 Variable Variable
Value bit
Variable
Value3
Variable
- 69 -
ETX
M/S
Variable 0x03
ETX
0x03
Check Sum ETX
M/S
Variable Variable 0x03
(from Master or Slave)
Data
ETX
Setting Values
... 0x03
Get/Set Address Value
0x00 Variable ...
Value2 Value1 Value0
Variable Variable Variable