Operating The Base Station On The Pabx/Router - Gigaset A130 User Manual

Repeater mode
With a repeater you can increase the range of your base station. You will need to acti-
¢
vate repeater mode ( page 16). Repeater mode and No Radiation mode
¢
( page 16) cancel each other out.
Resetting the handset
You can reset individual settings and changes that you have made. Entries in the direc-
tory, the calls list and the handset's registration to the base station will be retained.
¤ u ¤ u
¤
MENU Settings OK
¤
OK
a
Cancel the reset with .
Resetting the base station
When restoring factory settings the No Radiation mode is deactivated, individual set-
tings are reset and all lists are deleted.
The date and time are retained. The answer machine (AL130A/AL230A only) is ready
for use approx. 15 seconds after the base has been reset.
Resetting the base via the menu
Handsets are still registered, the system PIN is not reset.
¤ u ¤ u
¤
MENU Settings OK
Resetting the base using the key on the base
All handsets are de-registered and the system PIN is reset to the original code 0000.
Carry out the following steps: Remove the mains cable from the base. Hold down the
registration/paging key on the base (
cable to the base at the same time. Hold the key down for at least 5 seconds.

Operating the base station on the PABX/router

Operating on the router
When operating the Gigaset on an analogue port of a router you can reduce problems
with echoes by activating the Echo mode (
echoes, this function should be deactivated.
Operating on the PABX
The following settings are only necessary when your PABX requires them; see the user
guide for your PABX.
When entering the digits, enter them slowly one after the other.
¤ u
¤
Handset OK Reset Handset
¤ u
¤ ¤ ¤
Base OK Base Reset OK
¢ ¢
page 1)( page 2) and reconnect the power
¢
page 16). If you have no problems with
12
Changing the dialling mode
P#Q5#1N
¤
MENU
0 = touch tone dialling (DTMF); 1 = dial pulsing (DP)
Setting recall
P#Q5#1Q
¤
MENU
0 = 80 ms; 1 = 100 ms; 2 = 120 ms; 3 = 400 ms; 4 = 250 ms; 5 = 300 ms; 6 = 600 ms;
¤
7 = 800 ms
¤ ¤
OK Reset?
Changing pause after line seizure
You can set the length of the pause inserted between pressing the talk key
sending the phone number.
P#Q5#1L
¤
MENU
= 1 sec.; 2 = 3 sec.; 3 = 7 sec.
Changing the pause after the recall key
P#Q5#12
¤
MENU
= 800 ms; 2 = 1600 ms; 3 = 3200 ms
Appendix
¤
Reset? OK
Entering letters/characters
Standard
characters
Press the relevant key
the number of times
indicated.
Briefly press the hash
#
key to switch from
"Abc" to "123" mode,
from "123" to "abc"
mode and from "abc"
to "Abc" mode.
¤
The number for the set dialling mode flashes:
¤
The number for the current recall flashes:
¤
.
enter number OK
¤
The number for the current pause length flashes: 1
¤ ¤
enter number OK
¤
The number for the current pause length flashes: 1
¤
enter number
1x 2x 3x 4x 5x 6x 7x 8x 9x 10x 11x 12x 13x 14x 15x
1
1 £ $ ¥ ¤
2
a b c 2 ä
I
d e f 3 ë
4
g h i 4 ï
5
j k l 5
L
m n o 6 ö
M
p q r s 7
N
t u v 8 ü
O
w x y z 9
Q
1)
. , ? !
P
* / ( ) <
#
# @ \
1) Space
¤ ¤
.
enter number OK
b
and
.
¤
.
OK
á à â ã ç
é è ê
í ì î
ñ ó ò ô õ
ß
ú ù û
ÿ ý æ ø å
0 + - : ¿ ¡ " ' ; _
= > %
& §