Table of Contents
Advertisement
Activating/deactivating the ringer
Deactivating/reactivating the ringer permanently
In idle status, press and hold the star key
Deactivating the ringer for the current call
¤
¤
§Menu§
§OK§
Silent
Setting ring tones of the base station (A410A only)
Set the Ringer Volume, Ringer Melody and the Time Control for the base station:
¤ q
¤
§Menu§
Settings
¤ q
Ringer Volume/Ringer Melody/Time Control
Perform the setting analogously to the description in "Setting ring tones of the handset".
Activating/deactivating music on hold
You can set that your external participant hears music in case of internal recall and during call transfer.
P#Q5#1M
¤
§Menu§
Repeater mode
With a repeater, you can increase the range of your base station. You will need to activate repeater mode (
Repeater mode and No Radiation mode (
Resetting the handset
You can reset individual settings and changes that you have made. Entries in the directory, the calls list and the handset's
registration to the base station will be retained.
¤ q
¤
§Menu§
Settings
Restoring the base station
When restoring factory settings:
◆
Individual settings are reset.
◆
All lists are deleted.
◆
The No Radiation mode is deactivated.
The date and time are retained. The answering machine (A410A only) is ready for use approx. 15 seconds after the base
station has been reset.
Resetting the base station via the menu
When resetting via the menu
◆
Handsets are still registered.
◆
The system PIN is not reset.
¤ q
¤
§Menu§
Settings
Resetting the base station using the key on the base station
When resetting the base station using the key on the base station
◆
All handsets are de-registered and
◆
The system PIN is reset to the original code 0000.
Carry out the following steps: Remove the mains cable from the base station. Hold down the registration/paging key
¢
on the base station (
for at least 5 seconds.
Operating the base station on the PABX/router
Operating on the router
When operating the Gigaset on an analogue port of a router, you can reduce problems with echoing by activating the
¢
XES Mode (
page 24). If you have no problems with echoing, this function should be deactivated.
Operating on the PABX
The following settings are only necessary when your PABX requires them, see the user guide for your PABX.
When entering the digits, enter them slowly one after the other.
Changing the dialling mode
P#Q5#1N
¤
§Menu§
¤
1 = dial pulsing (DP)
enter number
P
. If the ringer is deactivated, the
¤ q
¤
¤
§OK§
§OK§
Base
¤
The number for the current setting flashes: 0 = off; 1 = on
¢
page 24) cancel each other out.
¤ q
¤
§§OK§§
§§OK§§
Handset
¤ q
¤ q
¤
§OK§
§OK§
Base
page 2) and reconnect the power cable to the base station at the same time. Hold the key down
¤
The number for the set dialling mode flashes: 0 = touch tone dialling (DTMF);
¤
§OK§
.
15
¤
§OK§
Audio Settings
¤ q
Reset Handset
¤
¤
§OK§
Base Reset
Ú
icon appears in the display.
¤
¤
¤
§§OK§§
§§OK§§
Reset?
¤
§OK§
Reset?
¤
¤
§OK§
enter number
.
¢
page 24).
Advertisement
Table of Contents
