Summary of Contents for Extron electronics VersaTools MDA 2V EQ
Page 1
User’s Manual MDA 2V EQ, MDA 4V EQ, and MDA 4SV EQ VersaTools ® Video Mini Distribution Amplifiers Extron Electronics, USA Extron Electronics, Europe Extron Electronics, Asia Extron Electronics, Japan 1230 South Lewis Street Beeldschermweg 6C 135 Joo Seng Road, #04-01...
Page 2
Precautions Safety Instructions • English FCC Class A Notice Warning This symbol is intended to alert the user of important Power sources • This equipment should be operated only from the power source indicated on the product. This equipment is intended to be used with a main operating and maintenance (servicing) instructions power system with a grounded (neutral) conductor.
Page 4
Quick Start Guide — MDA EQ Series To install and set up an MDA EQ Series mini distribution amplifier, follow these steps: Step 1 Turn all of the equipment off and disconnect it from the power source. Step 2 Mount the MDA EQ on a projector, under a desktop, or on a rack shelf, as illustrated below.
Table of Contents Quick Start Guide — MDA EQ Series, cont’d Chapter 1 • Introduction ............1-1 About this Manual ..............1-2 Smooth Ridges About the MDA EQ Series Mini Distribution Amplifiers .................. 1-2 SECTION A–A Models ..................1-2 Features .................. 1-2 Power Supply Tie Wrap Output Cord...
Table of Contents, cont’d MDA EQ Series Chapter One Introduction About this Manual About the MDA EQ Series Mini Distribution Amplifiers VersaTools ® MDA EQ Series • Table of Contents...
MDA EQ series to install and operate them. product. (These diagrams show connections for the MDA 2V EQ and the MDA 4SV EQ). Use them as guides for all About the MDA EQ Series Mini Distribution MDA EQ connections.
Introduction, cont’d MDA EQ Series Chapter Two Installation and Operation Mounting the MDA EQ Series Rear Panel Features and Cabling Front Panel Features and Operation VersaTools ® MDA EQ Series • Introduction...
Installation and Operation Mount the MDA EQ on the rack shelf, using two Mounting the MDA EQ Series 4-40 x 3/16" screws in opposite (diagonal) corners to The MDA EQ mini distribution amplifiers can be set on a table; secure the unit to the shelf. mounted on a rack shelf;...
Installation and Operation, cont’d Hold the unit with the attached brackets against the underside of the table or other furniture. On the mounting 6" Deep Rack Shelf 1/2 Rack Width Front False surface, mark the location of the bracket’s screw holes. Faceplate Drill 3/32"...
Installation and Operation, cont’d Attach the projector mounting bracket to the side of the • On the side mounting plates, the MDA is typically MDA EQ, using the provided machine screws. mounted on the outside of the bracket. • On the front mounting plate, the device is typically Secure the unit to a projector mount or other surface by mounted on the inside of the bracket.
Installation and Operation, cont’d Place the U-bolt around the ceiling pole and insert the two Mount Plate legs of the U-bolt through the round holes in the Flange contoured base, then through the slotted holes in the Extron MDA EQ Series bracket’s mounting plate.
This could result in the external DC power supply overheating and/or burning. MDA 2V EQ rear panel Stripping the wires to expose less than the recommended amount causes them to slide out of the connector too...
75 OHM simulates a monitor when none is attached to the Loop Thru connector. HIGH Z Output connectors (composite video) — Connect up to two (MDA 2V EQ) or four (MDA 4V EQ) composite video devices to 75 Ohm LOOP-THRU these BNC connectors.
Installation and Operation, cont’d MDA EQ Series GAIN GAIN GAIN GAIN GAIN GAIN GAIN GAIN S-VIDEO DISTRIBUTION AMPLIFIER MDA 4SV EQ Power indicator LED — This LED, when lit, indicates that the INPUT OUTPUTS MDA EQ is receiving power. Gain and Equalization potentiometers — (One set for each output for MDA 2V and 4V EQ;...
Page 16
Minimum/maximum levels 4.3 cm H x 10.9 cm W x 7.6 cm D MDA 2V EQ, MDA 4V EQ 0.4 V to 2 Vp-p with no offset at unity gain (Depth excludes connectors.) MDA 4SV EQ ....Y: 0.4 V to 2 Vp-p with no offset at unity Product weight ......
Page 17
Specifications, Parts, and Accessories, cont’d Models Optional Accessories These items can be ordered separately: Model Part number Part MDA 2V EQ 60-696-01 Accessory number MDA 4V EQ 60-697-01 1U, 9.5" Deep Universal Rack Shelf Kit 60-190-01 MDA 4SV EQ 60-698-01 (RSU 129) 1U, 9.5"...
Page 18
Specifications, Parts, and Accessories, cont’d VersaTools ® MDA EQ Series • Specifications, Parts, Accessories VersaTools ® MDA EQ Series • Specifications, Parts, Accessories...
Page 19
Specifications, Parts, and Accessories, cont’d VersaTools ® MDA EQ Series • Specifications, Parts, Accessories...
Need help?
Do you have a question about the VersaTools MDA 2V EQ and is the answer not in the manual?
Questions and answers