Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
Extron Electronics, USA
Extron Electronics, Europe
1230 South Lewis Street
Beeldschermweg 6C
Anaheim, CA 92805
3821 AH Amersfoort
USA
The Netherlands
714.491.1500
+31.33.453.4040
www.extron.com
Fax 714.491.1517
Fax +31.33.453.4050
© 2004 Extron Electronics. All rights reserved.
Extron Electronics, Asia
Extron Electronics, Japan
135 Joo Seng Road, #04-01
Daisan DMJ Building 6F
PM Industrial Building
3-9-1 Kudan Minami
Singapore 368363
Chiyoda-ku, Tokyo 102-0074 Japan
+65.6383.4400
+81.3.3511.7655
Fax +65.6383.4664
Fax +81.3.3511.7656
User's Manual
MDA 2V EQ, MDA 4V EQ,
VersaTools® Video Mini Distribution Amplifiers
and MDA 4SV EQ
68-978-01 Rev. A
Printed in USA
09 04
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Extron electronics VersaTools MDA 2V EQ
Summary of Contents for Extron electronics VersaTools MDA 2V EQ
- Page 1 Extron Electronics, Japan Daisan DMJ Building 6F 3-9-1 Kudan Minami Chiyoda-ku, Tokyo 102-0074 Japan +81.3.3511.7655 Fax +81.3.3511.7656 MDA 2V EQ, MDA 4V EQ, and MDA 4SV EQ VersaTools® Video Mini Distribution Amplifiers 68-978-01 Rev. A Printed in USA 09 04...
-
Page 2: Fcc Class A Notice
Precautions Safety Instructions • English Warning This symbol is intended to alert the user of important Power sources • This equipment should be operated only from the power source indicated on the product. This equipment is intended to be used with a main operating and maintenance (servicing) instructions power system with a grounded (neutral) conductor. - Page 3 Quick Start Guide — MDA EQ Series To install and set up an MDA EQ Series mini distribution amplifier, follow these steps: Step 1 Turn all of the equipment off and disconnect it from the power source. Step 2 Mount the MDA EQ on a projector, under a desktop, or on a rack shelf, as illustrated below.
-
Page 4: Table Of Contents
Quick Start Guide — MDA EQ Series, cont’d Smooth Ridges SECTION A–A Power Supply Output Cord Wiring the power cord Step 4 Connect power cords to the input and the outputs, and turn on the equipment. Step 5 Adjust the potentiometers for the outputs, using an Extron Tweeker. If using very short output cables, set all pots to the default setting (the arrow on the pot pointing to the dot beside it;... -
Page 5: Chapter 1 • Introduction
Table of Contents, cont’d MDA EQ Series Chapter One Introduction About this Manual About the MDA EQ Series Mini Distribution Amplifiers VersaTools® MDA EQ Series • Table of Contents... -
Page 6: About This Manual
The following diagrams give examples of how the various supported devices can be connected to an MDA EQ series product. (These diagrams show connections for the MDA 2V EQ and the MDA 4SV EQ). Use them as guides for all MDA EQ connections. Projector... -
Page 7: Chapter 2 • Installation And Operation
Introduction MDA EQ Series Chapter Two Installation and Operation Mounting the MDA EQ Series Rear Panel Features and Cabling Front Panel Features and Operation VersaTools® MDA EQ Series • Introduction... -
Page 8: Mounting The Mda Eq Series
Installation and Operation, cont’d Mounting the MDA EQ Series The MDA EQ mini distribution amplifiers can be set on a table; mounted on a rack shelf; attached to a projector; or mounted under a desk, podium, or tabletop. Tabletop use Four self-adhesive rubber feet are included with the MDA EQ. -
Page 9: Furniture Mounting
Installation and Operation, cont’d 6" Deep Rack Shelf 1/2 Rack Width Front False Faceplate Front false faceplate uses 2 screws. Use 2 mounting holes on opposite corners. Mounting an MDA EQ on a 6-inch rack shelf Furniture mounting To furniture-mount the MDA EQ, use the optional under-desk mounting kit (part #70-212-01), as follows. -
Page 10: Rear Panel Features And Cabling
MDA EQ models. INPUT OUTPUTS MDA 2V EQ POWER HIGH Z 0.2A MAX 75 Ohm GAIN GAIN GAIN GAIN MDA 2V EQ rear panel GAIN GAIN GAIN GAIN INPUT INPUT OUTPUTS OUTPUTS MDA 4V EQ POWER HIGH Z HIGH Z 0.2A MAX... -
Page 11: Front Panel Features And Operation
75 OHM simulates a monitor when none is attached to the Loop Thru connector. Output connectors (composite video) — Connect up to two (MDA 2V EQ) or four (MDA 4V EQ) composite video devices to these BNC connectors. Output connectors (S-video) — Connect up to four S-video devices to these 4-pin mini DIN connectors. -
Page 12: Appendix A • Specifications, Part Numbers, And Accessories
Installation and Operation, cont’d Power indicator LED — This LED, when lit, indicates that the MDA EQ is receiving power. Gain and Equalization potentiometers — (One set for each output for MDA 2V and 4V EQ; one set for each pair of outputs for MDA 4SV EQ) Use an Extron Tweeker (a small screwdriver) to rotate these pots to adjust for gain and equalization when devices with long cables are connected. -
Page 13: Specifications
0.3 Vp-p for C of S-video Minimum/maximum levels MDA 2V EQ, MDA 4V EQ 0.4 V to 2 Vp-p with no offset at unity gain MDA 4SV EQ ... Y: 0.4 V to 2 Vp-p with no offset at unity gain Impedance ... -
Page 14: Included Parts
Specifications, Parts, and Accessories, cont’d Models Model MDA 2V EQ MDA 4V EQ MDA 4SV EQ Included Parts These items are included in each order for an MDA EQ series: Included parts 2-pin, 3.5 mm captive screw connector Desktop power supply...
Need help?
Do you have a question about the VersaTools MDA 2V EQ and is the answer not in the manual?
Questions and answers