1. Manuals
  2. Brands
  3. Town & Country Fireplaces Manuals
  4. Accessories
  5. TC30 Black Diamond
  6. Instructions manual

Town & Country Fireplaces TC30 Series C Instructions Manual

Black diamond burner kit for tc30 series c
Hide thumbs Also See for TC30 Series C:
Table of Contents

Advertisement

Quick Links

Download this manual
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
These instructions are supplementary to the Installation and
Operating Instructions supplied with the fi replace and should be
kept together. Refer to the Installation and Operating Instructions
for proper gas supply, safety requirements and operating
instructions
100308-12
TC30
BLACK DIAMOND
BURNER KIT
INSTRUCTIONS
PART#
TC30.NG03.C
For TC30 Series C
TC30.NG03.C
5056.429.03

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TC30 Series C and is the answer not in the manual?

Questions and answers

Related Manuals for Town & Country Fireplaces TC30 Series C

Summary of Contents for Town & Country Fireplaces TC30 Series C

  • Page 1 Operating Instructions supplied with the fi replace and should be kept together. Refer to the Installation and Operating Instructions for proper gas supply, safety requirements and operating instructions TC30 BLACK DIAMOND BURNER KIT INSTRUCTIONS PART# TC30.NG03.C For TC30 Series C 100308-12 TC30.NG03.C 5056.429.03...

  • Page 2: Contents Of Package

    Contents of Package NOTE: MUST BE USED WITH PORCELAIN PANEL SET PART# TC30.PNLPBKB MANIFOLD ASSEMBLY (including supply tube) BURNER TUBE BURNER SHIELD MEDIA SPACER, Center MEDIA SPACER, Front MEDIA SPACER, Rear HARDWARE PACKAGE 5 lbs. GLASS MEDIA BURNER TRAY PILOT SHIELD (including pilot and pilot supply tube) TC30.NGO3.C 100308...
  • Page 3 Black Diamond Burner Installation Fig #1 A porcelain panel set must be used in conjunction with the installation of the burner assembly. See Installation and Operating Instructions manual for details. NOTE: Plug the 4 vacant holes in the bottom of the fi rebox with 1/2” screws, as they are not required to attach this style of burner.
  • Page 4 5. Install burner shield by tipping the shield Fig #5 into the fi rebox. Route pilot up through the opening in the burner shield. (Fig. #5) INSTALLING BURNER SHIELD Fig #6 6. Attach the burner tray to the burner shield using two screws at the back of the tray.

  • Page 5: Burner Installation

    8. Front and rear media spacers are now Fig #8 installed. (Fig. #8 & 9) REAR MEDIA SPACER Fig #9 FRONT MEDIA SPACER Fig #10 9. Install burner by tilting burner inlet through tray. Ensure that the orifi ce has entered the inlet tube.

  • Page 6: Glass Media Placement

    11. Install the center media spacer and secure Fig #11 to the tray with two 1 1/2” screws. (Fig. #11 & 12) Three holes must line up to set each screw. CENTER MEDIA SPACER Fig #12 Fig #13 GLASS MEDIA PLACEMENT 12.

  • Page 7: Propane Conversion

    Propane Conversion If the unit is to be used on propane WARNING convert as follows using the components supplied with this Fig #15 This conversion kit fi replace: shall be installed by a qualifi ed service agency Note: in accordance with the Factory supplied components must be used to ensure correct input.
  • Page 8 8. Remove the minimum rate screw located Fig #19 in the valve. (Fig. #19) The minimum rate screw is sealed with an o-ring. Use a thin bladed screwdriver to back the screw out to the limit of the threads. A groove on the screw body will be Minimum visibe just above the valve body.

  • Page 9: Gas Pressure Check

    Gas Pressure Check Note: To test the gas pressure, turn off the gas supply before removing the plug from Fig #25a the supply pressure test port or manifold pressure test port. Verify gas pressures with the fi replace lit and on the highest setting. SUPPLY PRESSURE MANIFOLD...

  • Page 10: Burner Flame Adjustment

    Burner Flame Adjustment The air shutter on the burner tube controls the primary combustion air to the gas burner and is preset at the factory for natural gas fuel. Some adjustment may be necessary to obtain desired fl ame and to eliminate carbon deposits. Evaluate fl ame appearance after the fi replace has reached operating temperature.

  • Page 11: Replacement Parts

    Replacement Parts (WHEN ORDERING, INCLUDE PART NUMBER WITH DESCRIPTION) ITEM .... DESCRIPTION ..............PART NO. #1....TC30 BLACK DIAMOND BURNER KIT ......TC30.NG03.C #2....BURNER TUBE ..............TC36. 5011835 #3....PILOT ASSEMBLY, CONVERTIBLE ......... 5005.025 #4....PILOT SUPPLY TUBE ............5019.225 #5....
  • Page 12 Technical support: 1-877-715-2664 Web site: www.townandcountryfi replaces.net 2975 Allenby Rd., Duncan, BC V9L 6V8 Printed in Canada...

This manual is also suitable for:

Tc30.ng03.c

Table of Contents