Zone Response Type Definitions - Honeywell ADEMCO VISTA-40 Installation And Setup Manual

ZONE # 1st 2nd
1 01 00
2 02 00
3 03 00
4 04 00
5 05 00
6 06 00
7 07 00
8 08 00
9 09 00
10 10 00
11 11 00
12 12 00
13 13 00
14 14 00
15 15 00
16 01 00
17 02 00
18 03 00
19 04 00
20 05 00

Zone Response Type Definitions

Each zone must be assigned a zone type, which defines
the way in which the system responds to faults in that
zone. There are three keypad-activated zones (panic
keys; see note) for each partition, a polling loop
supervision zone, and four RF supervisory zones, two
for each RF receiver installed. Zone types are defined
below.
Type 00: Zone Not Used
Program with this zone type if the zone is not used.
Type 01: Entry/Exit #1 Burglary
Provides entry delay whenever the zone is faulted and
the system is armed in the AWAY or STAY mode. When
the panel is armed in the INSTANT or MAXIMUM
mode, no entry delay is provided. Exit delay begins
whenever the control is armed, regardless of the arming
mode selected. These delays are programmable.
Assign this zone type to zones that are used for primary
entry to and exit from the facility.
Type 02: Entry/Exit #2 Burglary
Provides a secondary entry delay, if the system is
armed in the AWAY or STAY modes and the zone is
faulted. When the panel is armed in the INSTANT or
MAXIMUM mode, no entry delay is provided.
Secondary exit delay begins whenever the control is
armed, regardless of the arming mode selected. These
delays are programmable.
Assign this zone type to zones that are used for entry
and exit of the facility and require more time than the
primary entry and exit point. Delay times for this zone
type must be greater than those for zone type 01 (e.g., a
garage, loading dock, or basement door).
Communication Defaults for Zones
ZONE # 1st 2nd
21 06 00
22 07 00
23 08 00
24 09 00
25 10 00
26 11 00
27 12 00
28 13 00
29 14 00
30 15 00
31 01 00
32 02 00
33 03 00
34 04 00
35 05 00
36 16 00
37 17 00
38 18 00
39 19 00
40 10 00
ZONE # 1st 2nd
41 11 00
42 12 00
43 13 00
44 14 00
45 15 00
46 01 00
47 02 00
48 03 00
49 04 00
50 05 00
51 06 00
52 07 00
53 08 00
54 09 00
55 10 00
56 11 00
57 12 00
58 13 00
59 14 00
60 15 00
Type 03: Perimeter Burglary
Provides an instant alarm if the zone is faulted and the
system is armed in the AWAY, STAY, INSTANT, or
MAXIMUM mode.
Assign this zone type to all exterior door and window
zones.
Type 04: Interior, Follower
Provides a delayed alarm (using the programmed entry
delay time) if an entry/exit zone is faulted first.
Otherwise it produces an instant alarm. It is active
when the system is armed in the AWAY or MAXIMUM
mode, but the MAXIMUM mode eliminates the entry
delay.
Zones programmed for Interior Follower zone are
automatically bypassed when the panel is armed in the
STAY or INSTANT mode.
Assign this zone type to a zone covering an area such as
a foyer, lobby, or hallway through which one must pass
upon entry or exit (to and from the keypad).
Type 05: Trouble by Day/Alarm by Night
Provides an instant alarm if the zone is faulted and the
system is armed in the AWAY, STAY, INSTANT, or
MAXIMUM mode. During the disarmed state (day), the
system annunciates a latched trouble sounding from
the keypad (and a central station report, if desired).
Assign this zone type to a zone that contains a foil-
protected door or window (such as in a store), or to a
zone covering a sensitive area such as a stock room or
drug supply room. It can also be used on a zone in an
area where immediate notification of an entry is
desired.
Section 4 – Programming
ZONE # 1st
61 01
62 02
63 02
64 04
70 00
88 00
89 00
90 00
91 00
92 (DURESS) 11
95 00
96 00
97 06
99 06
ALARM RST. 00
TROUBLE 00
TRBLE. RST 00
BYPASS 00
BYP. RST. 00
2nd
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
4-5