VTech LS6425 Quick Start Manual

®
Quick start guide (Canada version)
LS6425/LS6425-2/LS6425-3/LS6425-4
Introduction
This quick start guide provides you with the basic installation
and use instructions. A limited set of features are described in
abbreviated form.
Please refer to the user's manual for complete installation and
.
operation instructions
Telephone base and charger installation
Install the telephone base and charger as shown below.
Telephone
Telephone base Electrical outlet
wall jack
power adapter not controlled
by a wall switch
If you have DSL
high speed Internet
Electrical
service, a DSL filter
outlet not
(not included) is
controlled
required.
by a wall
switch
A A
Telephone
line cord
Telephone base
Battery installation and charging
Install the battery as shown below. Once you have installed the battery,
you may be able to make and receive short calls. For best performance,
charge the handset battery continuously for at least 10 hours.
2. Place the battery with the
1. Plug the battery connector
securely into the socket label THIS SIDE UP facing
inside the handset battery up and the wires inside the
compartment, matching the battery compartment.
color-coded label.
3. Slide the battery compartment 4. Place the handset in the
cover towards the center of the telephone base or charger
handset until it clicks into place. to charge.
Handset overview
CHARGE light
On when the handset is
charging.
/ /VOLUME
Review the directory
when the telephone is not
in use.
Scroll up while in a menu.
Increase the listening
volume during a call or
message playback.
Move the cursor to the
right when entering
numbers or names in the
directory.
MUTE/DELETE
Mute the microphone
during a call.
Delete the displayed entry
while in the directory,
caller ID log or redial list.
Silence the ringer
Charger
temporarily while the
adapter
handset is ringing.
Delete digits or characters
while using the dialing keys.
/FLASH
Make or answer a call.
Answer a call waiting call
during a call.
1
Press repeatedly to add
or remove 1 in front of the
caller ID log entry before
dialing or saving it to the
directory.
Switch to tone dialing
temporarily while on a call.
Charger
/ SPEAKER
Make or answer a call using the
handset speakerphone.
Switch between the speakerphone
and the handset during a call.
REDIAL/PAUSE
Press to review the redial list.
Press and hold to insert a dialing pause
while entering numbers in the directory.
Telephone base overview
IN USE light
Flashes when there is an
incoming call, or another
telephone sharing the same
line is in use.
Flashes when the handsets
are being deregistered.
On when the
handset is in use,
or the answering
system is
answering a call.
On when a
CHARGE light
handset is being
remains on registered.
when charging.
/FIND HANDSET
Page all system handsets.
/REPEAT
Repeat a message or press twice
to play the previous message.
Using the menu
To enter the handset menu:
CID/ /VOLUME
1. Press MENU/
SELECT
Review the caller ID log when
2. Press or until the screen displays the desired feature menu.
the telephone is not in use.
Scroll down while in a menu. SELECT to enter that menu.
3. Press
MENU/
Decrease the listening volume
• To return to the previous menu, press
during a call or message
• To return to idle mode, press and hold
playback.
Move the cursor to the left when
entering numbers or names.
Telephone settings
MENU/SELECT
Default settings are indicated by asterisks (*).
Show the menu.
Choose an item, or save an Screen display
entry or setting while in a menu.
LCD language Set the screen display language.
PUSH TO TALK (PTT)
Begin a one-to-one or
one-to-group broadcast. Voice language Set the language to be used
for the voice prompts in your
OFF/CANCEL
answering system and voice
Hang up a call.
announce caller ID.
Silence the ringer
Annc Caller ID
Enable the telephone base and/or
temporarily while the
the handset to announce the
handset is ringing.
incoming caller ID information.
Press and hold to delete
Clr voicemail Turn off the
the missed call indicator
voicemail indicators.
while the telephone is
not in use.
Rename handset Change the name of each
registered handset.
Press to return to the
previous menu, or
Key tone
Adjust the key tone volume
press and hold to return
whenever a key is pressed, or turn
to idle mode without
it off.
making changes.
CID time sync
Enable the date and time to be set
Dialing keys
by incoming caller ID information.
Enter numbers or
Home area code Enter your home area code if you
characters.
dial only seven digits for local calls.
# (pound key) Dial mode
Set the telephone to be tone or
pulse dialing.
Press repeatedly to
show other dialing
options when reviewing
a caller ID log entry.
Set date and time
Switch the name order
Press MENU/
1.
SELECT
when saving the caller
2. Scroll to >Set date/time, then press
ID log entries to the
directory.
3. Press or to set the month, then press
EQ
-OR-
Change the audio quality to
Use the dialing keys (0-9) to enter the current month.
best suit your hearing during
4. Repeat Step 3 to set the correct date and year and then press
an outside call, intercom call,
message or announcement SELECT to advance to set the time.
MENU/
playback.
5. Repeat Step 3 until the time is set. Press
PM, or press 2 for AM or 7 for PM.
6. Press /SELECT to save.
MENU
Ringer volume (telephone base)
X/DELETE • Press /VOL or /VOL on the side of the telephone base to adjust
the ringer volume when the telephone is not in use.
Delete the message currently
playing.
Ringer volume (handset)
Press twice to delete all old
messages when the telephone
Press MENU/
1.
SELECT
is not in use.
2. Scroll to >Ringers, then press
Message window
3. Press /SELECT to select >Ringer volume.
MENU
Shows the number
4. Press or to sample each volume level, then press
of messages and
/SELECT to save your selection.
other answering MENU
system information.
Telephone operation
/SKIP
Make a call
Skip to the next
• Press or
message. /FLASH
-OR-
/ANS ON/OFF
• Predial by first dialing the telephone number and then press
Turn the answering
/SPEAKER.
or
/FLASH
system on or off.
/PLAY/STOP
Answer a call
Play messages.
• Press , /SPEAKER or any dialing key (0-9,
/FLASH
Stop message playback.
End a call
• Press OFF/
or charger.
when the telephone is not in use.
Redial list
Each handset stores the last 10 telephone numbers dialed.
/CANCEL.
OFF
To review and dial numbers from the redial list:
/CANCEL.
OFF
1. Press REDIAL/
2. Press
entry displays.
3. Press
To delete a redial entry:
Function Options
When the desired redial entry displays, press
English*
Français
Espaňol
Intercom
English*
Use the intercom feature for conversation between two system handsets.
Français
• Only one intercom call can be established with two handsets at
a time.
• If there is an incoming call while the originating handset is making
On*
an intercom request, the intercom request will be stopped.
Off
To initiate an intercom call:
Turn off When the handset is not in use, press MENU/
indicator? >Intercom, then press
• If you have more than two handsets, scroll to select a destination
HANDSET_ ___
handset, or use the dialing keys to enter a handset number.
*
To answer an intercom call:
Off
Press
destination handset.
On*
Off
To end an intercom call:
_ _ _ Press OFF/
or charger.
Tone*
Pulse
Push-to-talk (PTT)
You can directly broadcast messages from one handset to the
speakerphone of one or multiple handsets. Press and hold
PUSH TO TALK to begin two-way communication.
when the handset is not in use.
When the connection is made, both the caller and the destination
handsets display Press and hold [PTT] to talk and beep once.
/SELECT.
MENU
Only one handset can talk at a time. To do so, press and hold
SELECT.
MENU/
PUSH TO TALK.
Directory
The directory can store up to 50 entries, which are shared by all
system handsets.
or to select AM or
To add a directory entry:
1. Press MENU/
Scroll to >Directory, then press
2.
3. Scroll to >Add contact, then press
4. Use the dialing keys to enter the phone number (up to 30 digits).
-OR-
Copy a number from the redial list by pressing REDIAL/
and then press
number. Press
when the handset is not in use.
5. Press
/SELECT.
MENU
6. Use the dialing keys to enter the name (up to 15 characters).
Additional key presses show other characters of that particular key.
7. Press
While entering names and numbers, you can:
• Press
• Press and hold
/SPEAKER, and then dial telephone number.
• Press and hold
entering phone numbers only).
• Press
• Press 0 to add a space (for entering names only).
#
or ).
TONE
or put the handset to the telephone base
CANCEL
when the handset is not in use.
PAUSE
or REDIAL/
, repeatedly until the desired
PAUSE
or /SPEAKER to dial.
/FLASH
/DELETE.
MUTE
. Scroll to
SELECT
/SELECT.
MENU
/SPEAKER or any of the dialing keys on the
/FLASH
,
or place the handset back in the telephone base
CANCEL
when the handset is not in use.
SELECT
/SELECT.
MENU
/SELECT.
MENU
PAUSE
, or REDIAL/ repeatedly to select a
PAUSE
SELECT.
MENU/
/SELECT to move to the name.
MENU
/SELECT to store the entry.
MENU
/DELETE to backspace and erase a digit or character.
MUTE
/DELETE to erase the entire entry.
MUTE
/PAUSE to insert a dialing pause (for
REDIAL
or to move the cursor to the left or right.