Related Manuals for VTech CTM-A2116
Summary of Contents for VTech CTM-A2116
- Page 1 Analogue Contemporary Series CTM-A2116 Analogue 1-Line Hidden Base with Cordless Colour Handset and Charger NGC-S3410HC SIP 1-Line Cordless Colour Handset and Charger User‘s Guide...
-
Page 2: Important Safety Instructions
Important safety instructions When using your telephone equipment, basic safety precautions should always followed to reduce the risk of fire, electric shock and injury, including the following: 1. This product should be installed by a 10. Do not allow anything to rest on the qualified technician. - Page 3 • If the product has been dropped and 20. In wall mounting position, make sure the telephone base and/or handset has to mount the telephone base on the been damaged. wall by aligning the eyelets with the mounting studs of the wall plate. Then •...
- Page 4 • Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas; • Extremely low air pressure that can result in an explosion or the leakage of flammable liquid or gas.
-
Page 5: Table Of Contents
Telephone layout ......7 Speed dial ..........16 Analogue 1-Line Hidden Base with Cordless Message waiting indicator ..... 16 Colour Handset and Charger - CTM-A2116 7 Play messages ........... 16 SIP 1-Line Cordless Colour Handset and Charger - NGC-S3410HC ......... 7 Find handset .......... -
Page 6: Parts Check List
| Network cable in the illustration scale 40% handset) S211X BASE Artwork RESET Analogue 1-Line Hidden Base with Cordless CTM-A2116 Colour Handset and Charger PART DESCRIPTION COLOR/MATERIAL TEXTURE/FINISH 01. Left Housing Graphite Spray SPI B-1 Silkscreen on the Top ( ) - Pantone 8001C 02. -
Page 7: Telephone Layout
Telephone layout Analogue 1-Line Hidden Base with Cordless Colour Handset and Charger - CTM-A2116 SIP 1-Line Cordless Colour Handset and Charger - NGC-S3410HC Handset Battery charging light Colour screen Soft keys (3) Perform the action indicated by the on-screen labels. -
Page 8: Analogue 1-Line Hidden Base
Analogue 1-Line Hidden Base with Cordless Colour Handset and Charger - CTM-A2116 Analogue 1-Line Hidden Base FIND HANDSET button. Short press (for less than 2 seconds) to find the handset by making it ring. Short press again to stop handset ringing. -
Page 9: Installation
Installation IMPORTANT INFORMATION 1. Use only a compatible VTech power Analogue 1-Line Hidden Base with adapter. To order a replacement power Cordless Colour Handset and Charger adapter, call +44 (0)1706 694 070 or - CTM-A2116 email ukca@trustdistribution.com. Analogue 1-Line Hidden Base 2. - Page 10 To mount the base station on the wall 4. Check to make sure the plate is secure at top and bottom. It should be flush with the 1. Install two mounting screws on the wall. base station body. Choose screws with heads larger than 5.
-
Page 11: Analogue 1-Line Hidden Base With Cordless Colour Handset And Charger - Ctm-A2116
Analogue 1-Line Hidden Base with Installation Notes Cordless Colour Handset and Charger Avoid placing the base station, handset, or - CTM-A2116 handset charger too close to: SIP 1-Line Cordless Colour Handset • Communication devices such as television sets, DVD players, or other... -
Page 12: Handset Registration
You can register additional cordless handsets 2. With Registration selected, press OK. to the base station. The Base station 3. Press to select Deregister, and accommodates up to four CTM-A2116 or then press Select. CTM-S2115 cordless handsets. 4. Press to select the handset you 1. -
Page 13: Handset Battery Charging
Handset battery charging 3. Place the top of the battery in the handset battery compartment so that the battery The battery must be fully charged before connectors are aligned. using the cordless handset for the first time. 4. Push the bottom of the battery down into The battery charge light turns on when the the battery compartment. -
Page 14: Set Up
Set up Analogue 1-Line Hidden Base with Cordless Colour Handset and Charger - CTM-A2116 Default settings are indicated by asterisks (*). Setting Options Adjustable by Listening volume- Handset 1, 2, 3, 4, 5, 6*, 7 User and administrator Ringer tone... -
Page 15: Operation
The call ends Cordless Colour Handset and Charger when all handsets hang up. - CTM-A2116 Hold SIP 1-Line Cordless Colour Handset To place a call on hold: and Charger - NGC-S3410HC... -
Page 16: Switching Between Calls
when the phone is not in use. All idle cordless To answer the incoming call: handsets beep for 60 seconds. • Press Ans on the cordless handset. The active call is put on hold. To end paging: To ignore the incoming call: •... -
Page 17: Appendix
Appendix Troubleshooting If you have difficulty with the telephones, please try the suggestions below. For customer service, call +44 (0)1706 694 070 or email ukca@trustdistribution.com. For cordless telephone Question Suggestions • Make sure the power adapter is connected to the base station power jack, and plugged into an electrical outlet that is not controlled by a wall switch. - Page 18 Question Suggestions • Try all the above suggestions. Make sure there is a dial tone before dialing. It is normal if the cordless handset takes a second or two to synchronize with the base station before producing a dial tone. Wait an extra second before dialing.
- Page 19 Question Suggestions • Make sure the cordless handset is placed in the handset charger correctly. The battery charging light should be on. • Remove the battery and then install it again. Charge it for up to 11 hours. • If the cordless handset is in the The battery does not charge in the cordless handset charger but the battery handset or the battery does not accept charge.
- Page 20 Question Suggestions • Make sure the ringer volume is turned up on the cordless handset. • Make sure the power adapter is connected to the base station power jack, and plugged into an electrical outlet that is not controlled by a wall switch.
- Page 21 Question Suggestions • Reset the telephone base by unplugging the electrical power to the base. Wait for 15 seconds and plug it back in again. Allow up to one minute for the cordless handset and the telephone base to synchronize. The cordless handset beeps and is not •...
- Page 22 Question Suggestions • The cordless handset may be out of range. Move the handset closer to the base station or adjust the setting of RF transmission power. Refer page xx for details. • Appliances or other cordless telephones plugged into the same circuit as the telephone base can cause interference.
- Page 23 Question Suggestions • Disconnect the base station from the network wall jack and connect a different working telephone. If calls are still not clear, the problem is I hear other calls when using the telephone. probably in the wiring or telephone service.
-
Page 24: Vtech Hospitality Limited Warranty Program
During the limited warranty period, VTech’s authorised service representative will repair or replace, at VTech’s option, without charge, a Product that is not free from defects in materials and workmanship. If VTech’s authorised service representative repairs the Product, new or refurbished replacement parts may be used. -
Page 25: Maintenance
Avoid rough treatment arise through the use of this product. VTech Place the handset down gently. Save the Communications, Inc. and its suppliers original packing materials to protect your assume no responsibility for any damage or telephone if you ever need to ship it. -
Page 26: Disposal Of Batteries And Product
Disposal of batteries and product Product disposal instructions for business users ‚) ( These symbols on the products, If you wish to discard electrical and electronic packaging, and/or accompanying documents equipment, please contact your dealer or mean that used electrical and electronic supplier for further information. -
Page 27: Technical Specifications
Technical specifications Analogue 1-Line Hidden Base with Cordless Colour Handset and Charger - CTM-A2116 Analogue 1-Line Hidden Base SIP 1-Line Cordless Colour Handset and Charger - NGC-S3410HC Frequency control Crystal controlled PLL synthesiser Transmit frequency Handset: 1921.536-1928.448 MHz Base Station: 1921.536-1928.448 MHz... - Page 28 Index Mute 15 Place a call 15 Play messages 16 Answer a call 15 Receive a call 15 Battery 13, 26, 27 charging 13 Registration, Handset 12 Ringer volume 15 Call waiting 15 Speakerphone 15 Speed dial 16 Deregistration, Handset 12 Technical specification 27 End a call 15 Troubleshooting 17...
- Page 29 FCC Caution: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
- Page 30 Specifications are subject to change without notice. Copyright © 2021 VTech Telecommunications, Inc. All rights reserved. 09/21. CTM-A2116_NGC-S3410HC_UG_V1_CEC_EU-UK_2021.09.28...