Samsung SSC-17TQ Installation Manual
  1. Manuals
  2. Brands
  3. Samsung Manuals
  4. Security System
  5. SSC-17TQ
  6. Installation manual
Samsung SSC-17TQ Installation Manual

Samsung SSC-17TQ Installation Manual

Color dual quad observation system
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
COLOR DUAL QUAD
OBSERVATION SYSTEM
SSC-17TQ
INSTALLATION
MANUAL
POWER

Advertisement

Table of Contents
loading

Related Manuals for Samsung SSC-17TQ

Summary of Contents for Samsung SSC-17TQ

  • Page 1 COLOR DUAL QUAD OBSERVATION SYSTEM SSC-17TQ INSTALLATION MANUAL POWER...

  • Page 2: Important Safeguards

    8A. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven CAUTION surfaces may cause the appliance and cart combination to overturn. RISK OF ELECTRIC SHOCK 9. Ventilation : Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of DO NOT OPEN the video product and to protect it from overheating, and these openings must not be blocked or covered.

  • Page 3: Table Of Contents

    Contents Chapter 3: Setting each item function at SETUP MENU IMPORTANT SAFEGUARDS...........e-2 3-1) CLOCK/DISPLAY SET MENU function setting .....e-30 3-2) CHANNEL TITLE MENU function setting .....e-31 3-3) SYSTEM SET MENU function setting ......e-32 3-4) EVENT SET MENU function setting ......e-34 Chapter 1: System Components and Installation 3-5) EVENT LIST MENU function setting ......e-36 1-1) Environmental requirements for installation and safety ..e-6...

  • Page 4: Chapter 1: System Components And Installation

    Chapter 1: System Components and Installation 1-2) System Components The system consists of the following: 1-1) Environmental requirements for installation and safety This section describes the environmental requirements for safe installation and use. Install the product on a flat table or in a rack. It should be used only when level and should not be used when stood vertically or obliquely.

  • Page 5: 1-3) Camera Composition And Installation Method

    CAMERA BRACKET (M4 x L15) CAMERA CABLE MCB-60 6PIN SHIELD CABLE 60ft(1ft=0.3048m) CAMERA CABLE MCB-100 6PIN SHIELD CABLE 100ft(1ft=0.3048m) INSTALLATION MANUAL SSC-17TQ PIN NUMBER SPEC POWER CORD CBF-POWER CORD SPEAKER(HOT) VCR CABLE BNC DIN CABLE ASSY VIDEO_OUT SENSOR CONNECTOR TERMINAL-BLOCK...
  • Page 6 f. Speaker 3) PIR Camera composition It outputs the sound signal which was transfered from the monitor. <Top> <Bottom> • PIN configuration of the PIR CAMERA is the same as the STANDARD e-10 e-11 CAMERA. • But, PIR CAMERA does not provide ALARM JACK. 2) INSTALLING STANDARD CAMERA (SOD14C) SOD14C s camera can be attached to the wall, ceiling or shelf using the camera mount bracket (SBR-110).
  • Page 7 6-pin modular jack <Sensor Detection Angle & Area> Used to connect the camera to the monitor. 1> Vertical Detection Line e-12 e-13 PIN NUMBER SPEC SPEAKER(HOT) VIDEO_OUT SPEAKER(COLD) AUDIO_OUT/ALARM_OUT 12V DC • Please consider the horizontal detection area and the vertical detection line when choosing an installation site.
  • Page 8 Camera installation Hints <Inside> 1. Do not install directly towards rising or setting sun. Can cause burn or damage to internal options. 2. Do not limit desired detection zone by interference of curtains, screens, potted plants, etc. 3. Also, do not locate it in front of source of water/oil vapors. Avoid placement of heat source inside e-14 e-15 detection zone...
  • Page 9 4) INSTALLING THE PIR CAMERA (SMM-PIRCAM) 4. Connect the Camera connector(RJ-11) cable to the case-rear as well as the cable to be connected to 1. Choose an installation site that can sufficiently support 5 times the weight of the equipments to be the terminal.
  • Page 10 6. Adjust the direction of the lens. 4) CAMERA MOUNT BRACKET(SBR-110) & STANDARD CAMERA(SOD14C) 1) Use the cross (+) screw driver to turn the screw (indicated by the arrow in the illustration) counterclockwise slightly. The lens body will move. (1) Overview 2) Tilt the lens body down about 10°...

  • Page 11: 1-4) Camera Composition And Connecting Method To System

    1-4) CAMERA Composition and Connecting Method to • Loosen the handle by turning it in a counterclockwise direction and then adjust the camera SYSTEM position . Tighten the handle, turning it clockwise, and lock the camera in position. After positioning monitor and installing three cameras to a desired location, please connect CAMERA e-20 e-21 to SYSTEM through CAMERA CABLE (MCB-60 or MCB-100) as shown in the below figure.

  • Page 12: 1-6) Whole System Connection And Configuration

    1-5) External terminal connecting method for CAMERA and f) Connect the A/O (HOT) terminal on the rear panel to the Alarm IN terminal of the VCR. SYSTEM g) Connect the A/O (COLD) terminal on the rear panel to the Ground terminal of the VCR. h) Connect the A/R terminal on the rear panel to the Alarm Reset terminal of the VCR.

  • Page 13: 1-7) Rear Panel Function

    1-7) REAR Panel function 1-8) Mounting the DIGITAL DUAL QUAD (SOQ-080N) ACCESSORY e-24 e-25 Screws (BH M3X6, 4EA) Screws (TH M4X20, 4EA) Rack Mount Adapters (2EA) a. CAMERA IN (RJ-11) Video camera input terminals. You Can connect up to 8 Cameras with RJ-11 connectors. 1) Assemble the fixing holes of the b.

  • Page 14: Chapter 2: Remote Control Function And Using Method

    Chapter 2: REMOTE CONTROL 2-4) SET- KEY Function and Using Method Alarm function and loss function can be cancelled while the alarm or loss is working. e-26 e-27 The Remote Controller(REMOCON) is contained in the 17" TFT-LCD Monitor (SMT-170). 2-5) QUAD/PAGE- KEY 2-1) TALK KEY Allows users to display QUAD A or QUAD B at QUAD DISPLAY MODE.

  • Page 15: 2-7) Pip- Key

    2-7) PIP- KEY 2-12) ENTER- KEY Can be used to see the main screen while Single screen is displayed. The main screen can be changed As a multi functional ENTER key, it is used for 1. entering from the menu into the submenu, 2. moving and transfered to another channel while PIP is working.

  • Page 16: Chapter 3: Setting Each Item Function At Setup Menu

    Chapter 3: Setting each item function at SETUP DATE TYPE: MM/DD/YY YY/MM/DD DD/MM/YY. DATE [MM/DD/YY] MENU • Month(MM) : 01 ~ 12 • Day(DD) : 01 ~ 31 Pressing the MENU BUTTON of the FRONT PANEL allows users to enter SETUP MENU and see the e-30 e-31 •...

  • Page 17: 3-3) System Set Menu Function Setting

    3-3) SYSTEM SET MENU function setting PIP POSITION: BOTTOM-RIGHT TOP-LEFT TOP-RIGHT BOTTOM-LEFT. • Select the PIP position among the four options listed above. You may change DWELL TIME, PIP POSITION, BORDER COLOR, LOSS CHANNEL COLOR, BORDER COLOR: GRAY WHITE BLACK. SYSTEM ID.

  • Page 18: 3-4) Event Set Menu Function Setting

    3-4) EVENT SET MENU function setting EVENT DETECT... You may change EVENT HOLD TIME, EVENT BUZZER, EVENT DETECT. • Select “EVENT DETECT...” with the UP/DOWN button and click the ENTER button. If you click the UP/DOWN button to select 4. EVENT SET in the SETUP MENU and click the e-34 e-35 Then the following screen pops up.

  • Page 19: 3-5) Event List Menu Function Setting

    3-5) EVENT LIST MENU function setting Chapter 4: DISPLAY MODE setting method You can check the ALARM/LOSS EVENT LIST. If you click the UP/DOWN button to select 5. EVENT LIST in the SETUP MENU and click the ENTER button, the following screen will be 4-1) SINGLE SCREEN DISPLAY e-36 e-37...

  • Page 20: 4-2) Quad Mode Display

    4-2) QUAD MODE DISPLAY 4-3) AUTO SEQUENTIAL DISPLAY MODE Users can switch SINGLE DISPLAY MODE and SEQUENTIAL DISPLAY MODE to QUAD Pressing on the SEQUENCE KEY on the front allows screen to automatically switch to SINGLE DISPLAY MODE, or QUAD A (QUAD B) to QUAD B (QUAD A), or PIP MODE to QUAD MODE, MODE full screen or QUAD MODE.

  • Page 21: 4-4) Pip Mode Display

    4-4) PIP MODE DISPLAY 4-5) ZOOM MODE DISPLAY This is available in Single Screen mode. While in a single screen display, press the ZOOM key to display the zoom area. When in a PIP screen, you can use the UP and DOWN buttons to change the main channel and use the Use the LEFT, RIGHT, UP, and DOWN keys to move to the area you want to zoom in, and then press e-40 e-41...

  • Page 22: Chapter 5: Each Product Feature

    Chapter 5: Each product feature SMM-PIRCAM : PIR Camera SMM-PIRCAM Model Name SOD14C : Standard Camera NTSC STANDARD Broadcasting System e-42 e-43 1/4'' SUPER HAD IT CCD Imaging Device SOD14C Model Name 510(H) x 492(V) Effective Pixels NTSC STANDARD Broadcasting System Internal Synchronization 1/4 ”SUPER HAD IT CCD...

  • Page 23: Soq-080N : Digital Dual Quad

    Memo SOQ-080N : DIGITAL DUAL QUAD • CAMERA 8 Input: 1.0Vp-p(CVBS), 75Ω Video Input • VCR 1 Input (to Video Out of VCR) : 1.0Vp-p, 75Ω e-44 • BNC 8 Output: 1.0 Vp-p, 75Ω, S-Jack Type, CVBS Video Output • VCR 1 Output: 1.0 Vp-p, 75Ω , S-Jack Type, CVBS •...
  • Page 24 Memo...
  • Page 25 Samsung CCTV dba GV1 1621 West Crosby, Suite 104 Part No.: AB68-00403A (Rev.01) Carrollton, TX. 75006 Printed in Korea PHONE : 866.492.8246...

Table of Contents