Download Print this page

Advertisement

CH01

Advertisement

   Also See for LG CED-8080B

   Related Manuals for LG CED-8080B

   Summary of Contents for LG CED-8080B

  • Page 1

    CH01...

  • Page 2

    CAUTION : The laser used in the CD-R/RW drive can damage your eyes. Do not attempt to open the cover. To reduce the risk of electric shock, do not remove cover (or back). No user-serviceable parts inside. Refer servicing to qualified service personnel. Use of controls or performance of procedures other than those specified here in may result in hazardous radiation exposure.

  • Page 3

    Industry Canada requirement This class B digital apparatus meets all requirements of the Canadian Interference- Causing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. FCC COMPLIANCE STATEMENT Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

  • Page 4

    (2) this device must accept any interference received, including interference that may cause undesired operation. Trade Name/Model : LG or GoldStar/CED-8080B or CED-8083B Responsible Party : LG Electronics U.S.A. Inc. Address: 6133 N. River Road, Suite 1100...

  • Page 5: Table Of Contents

    Warranty ........18 CED-8083B: 4X Record ReWrite /32X Read CED-8080B: 8X Record ReWrite /32X Read * Writing speed depends on capabilities of discs. As a result, you should...

  • Page 6: Features

    DirectCD v2.5b(s) Introduction Thank you for Features purchasing this • Running OPC* gives a flatter writing signal that improves reliability. CD-R/RW Drive. • Easy-to-use tray model. • Enhanced-IDE (ATAPI) model. • Can read not only CD-R and CD-RW discs, but also video CDs, music CDs, and photo CDs.

  • Page 7: Important Precautions

    DirectCD v2.5b(s) Important Precautions Follow these precautions when handling the drive or discs. Precautions • Please take notice that the manufacturer of this equipment does not offer any warranty against data loss due to inappropriate installation or handling, or direct or indirect damages. •...

  • Page 8: System Environment

    DirectCD v2.5b(s) System Environment Computer This unit can be operated in the system environment explained here. 200MHz (or faster) Pentium (for 8X speed, System 233MHz or faster recommended) requirements Memory Windows 98/95 : 32MB or greater. Windows NT Workstation Ver. 4.0: 32MB or greater (64MB or over recommended) Hard disk Hard disk with average access time of 19 msec...

  • Page 9: Location And Function Of Controls

    DirectCD v2.5b(s) Location and Function of Contro l s Front Panel Emergency Eject Hole Disc Tray Stop/Eject Button Play/Skip Button Headphone Jack Volume Drive Activity Indicators Control 1. Disc tray This is the tray for the disc. Place the disc on the ejected disc tray, then lightly push the tray (or push the eject button) and the CD will be loaded.

  • Page 10

    DirectCD v2.5b(s) Analog Audio Output Rear Panel IDE Interface Connector Connector Power Jumper Connector Digital Audio Connector Output Connector 1. Power Connector Connects to the power supply (5-and 12-V DC) of the host computer. NOTE : Be careful to connect with the proper polarity. Connecting the wrong way may damage the system (and is not guaranteed).

  • Page 11: Installing The Drive

    DirectCD v2.5b(s) Installation Installing the Drive Before Before installing the drive, please note the following points. I You will need the following: Installation • A screw driver of a suitable size to fit the securing screws for the drive unit. •...

  • Page 12

    ″ drive bay panel from the computer. Refer to Mounting 1. Remove the 5 the manual for the computer for details. the Drive 2. Insert the drive unit into the bay. Do not apply excessive pressure to the cables inside the computer. 3.

  • Page 13

    Connecting Connect the 40 pin IDE cable to the back of the CD-R/RW Drive, making sure the coloured (red) stripe on the IDE cable is connected to pin 1 on the CD-R/RW drive. Interface NOTE : Generally, the IDE connector is keyed and will only fit one way.

  • Page 14

    Jumper Before installation, set the jumper on the jumper connector on the rear panel. Setup The drive can be connected as the Master or Slave on an EIDE (ATAPI) interface. When several (up to four) EIDE devices are connected, each must be set in a unique way. Specific knowledge of hardware and software is necessary to install the drive.

  • Page 15

    The CD-R/RW drive connects to the motherboard of the host computer using an IDE interface cable. You may connect the CD- Connection R/RW Drive as a Slave or Master device, depending on your computer. To Install as To install the drive as a Master, the jumper can be left as supplied from the factory.

  • Page 16

    To Install as To install the drive as a Slave, change the jumper setting on the rear panel to SL. a Slave Drive Master drive (Booting hard disk) Slave drive (CD-R/RW drive) - OR - Master drive (Booting hard disk) Master drive (Other IDE drive) Slave drive...

  • Page 17: Device Drivers

    Device Drivers When using Windows 98/95 or Window NT Workstation Ver.4.0, no special device driver is required. ″ floppy This CD-R/RW drive is supplied with MS-DOS drivers on a 3 disk. These drivers are required to use the CD-R/RW drive in DOS or to enable the CD-ROM disk.

  • Page 18

    Running 1. Insert the diskette into the appropriate drive. 2. Go to the floppy drive by typing A: or B: at the DOS prompt, as the Install appropriate. Program 3. Type the word INSTALL and press [ENTER]. (MS-DOS 4. The INSTALL program will begin loading. When loading is Installation) complete, the INSTALL program identification will appear on screen.

  • Page 19: How To Use The Discs

    Operation How to Use the Discs When using CD-ROM discs, CD-R discs or CD-RW discs, don’t attach any stickers or labels to the discs. Using discs with them attached not only causes read and write errors, but data on the disc may be lost due to damage to the disc itself.

  • Page 20: Troubleshooting

    DirectCD v2.5b(s) Appendix Troubleshooting Before Before calling for service, check this list. • The drive doesn’t have power. Requesting • Is the power supply cable from the host computer plugged in? Service • Is the Power Connector to the drive securely attached? •...

  • Page 21: Specifications

    Data Transfer Rate Read : 14 to 32X CAV: 2.1MB to 4.8MB/sec Write : 2X: 300KB/sec. 4X: 600KB/sec. 8X: 1200KB/sec(Model : CED-8080B only.) ∗ Burst (ATAPI) 16.67MB/sec (PIO Mode 4, MULTI-DMA Mode 2) Average access time Random 100m sec <Typical>...

  • Page 22: Warranty

    Internet Address : http :// www. LGEservice.com CD-R/RW LIMITED WARRANTY LG Electronics Inc. will repair or at its option replace*, without charge, your product which proves to be defective in material or workmanship under normal use, during the warranty period listed below from the data of original purchase.

  • Page 23

    Copyright © 1999 LG Electronics Inc. LG Electronics U.S.A. Inc. 1000 Sylvan Ave. Englewood Cliffs NJ 07632 U. S. A. LG Electronics Canada Inc. 235 Superior Blvd, Mississauga Ontario, Canada LG Electronics Deutschland GMBH Jakob-Kaiser-Straße 12, D-47677 Willich, Germany LG Electronics U. K. Ltd.

This manual also for:

Ced-8083b

Comments to this Manuals

Symbols: 0
Latest comments: