Onkyo DV-CP706 Setup Manual page 2

What to Do if There's No Sound or Picture
Press the remote controller's [RESOLU-
TION] button. When "HDMI OFF"
appears on the display, press the button
again to select "HDMI ON."
If HDMI is already on, the currently selected resolution
(e.g., 480p) will be displayed.
Try pressing the remote controller's
[RESOLUTION] button repeatedly to
select another resolution.
If you want to use HDMI with 720p or 1080i, make sure
that your TV supports these resolutions.
480p (480p/576p)
720p
You can check the status of the HDMI connection by pressing and holding down the DV-CP706's [DISPLAY] button for
10 seconds until a message ID appears on the display. Look up the message ID in the following tables and check the
HDMI connections and settings on both the DV-CP706 and the connected component. The page numbers in parentheses
refer to the DV-CP706 Instruction Manual.
HDMI connection and HDMI-related settings status
Displayed ID
MSG ID 001 Turn the DV-CP706 and the connected component off, then turn them on again. Make sure that the con-
MSG ID 005 nected component is working properly and that the DV-CP706's HDMI settings are configured suitably for
MSG ID 015 that component.
No picture from the HDMI connection
Displayed ID
MSG ID 002 The HDMI Output Setting is set to Off. Change it to On (page 45).
MSG ID 003 The HDMI cable may not be connected properly. Check the connection. Also, make sure the HDMI input
MSG ID 004 on the TV or AV receiver is correctly configured to received HDMI.
Make sure the HDMI input on the TV or AV receiver is correctly configured to received HDMI.
MSG ID 005 The connected component may not support HDCP. Make sure the connected component supports HDCP.
MSG ID 006 Turn the DV-CP706 and the connected component off, then turn them on again.
MSG ID 007 The DV-CP706 may be connected to the other component's DVI jack. Some TVs may not properly receive
the video output by the DV-CP706. Also, with a DVI connection, there will be no sound.
The DV-CP706's HD Resolution setting is set to 720p or 1080i. If your TV doesn't support these resolu-
MSG ID 008
tions, select another resolution (page 24).
The connected component may not be receiving the HDMI signal properly.
MSG ID 009
Try selecting another resolution on the DV-CP706 (page 24).
No sound from the HDMI connection
Displayed ID
MSG ID 010 The DV-CP706's Digital/HDMI Audio Out setting is set to Off. Change the setting to All or PCM (page 46).
MSG ID 011 The connected component may not support 96 kHz PCM. Set the DV-CP706's Linear PCM Out setting to
MSG ID 014 Down Sample On (page 46).
MSG ID 012 The connected component may not support Dolby Digital. Set the DV-CP706's Digital/HDMI Audio Out
MSG ID 013 setting to PCM (page 46).
The connected component may not support DTS.
MSG ID 016
The DV-CP706 cannot play the DTS format audio or soundtrack. On your DVD-Video disc's audio setup
MSG ID 017
menu, select an audio format other than DTS.
For more information, refer to the manuals for the DV-CP706 and the other component.
SN 29344790
(C) Copyright 2008 ONKYO CORPORATION Japan. All rights reserved.
480i (480i/576i) AUTO
1080i 1080p
If you select a resolution that's not supported by your
TV, vertical lines may appear on your TV and the picture
will not be displayed correctly. In this case, press the
[RESOLUTION] button repeatedly to find a resolution at
which the picture is displayed correctly.
Using RIHD
To use RIHD, make sure CEC is enabled on your other
CEC-compatible AV components (e.g., TV or AV receiver).
On the DV-CP706, make sure the HDMI Control, Power
Control, and Direct Change settings are all set to On.
About RIHD-compatible Components
The TVs listed below (in no particular order) are com-
patible with RIHD.
• Panasonic TVs that support VIERA LINK
• Toshiba TVs that support CE-LINK
Components other than those listed here may also provide
linked operation if they support the CEC part of the HDMI
standard, however, operation cannot be guaranteed.
Message
Message
Message
I0806-1
* 2 9 3 4 4 7 9 0 *