Connecting Cable Tv - Samsung FP-T5084 Owner's Instructions Manual

I
Connecting Cable TV
To connect to a cable TV system, follow the instructions below.
Cable without a Cable Box
1 Plug the incoming cable into the ANT 2 IN(CABLE) terminal on the back of the TV.
)0>-
Because this TV is cable-ready, you do not need a cable box to view
unscrambled cable channels.
Connecting to a Cable Box that Descrambles All Channels
1 Find the cable that is connected to the ANT OUT terminal on your cable box.
)0>-
This terminal might be labeled "ANT OUT", "VHF OUT" or simply, "OUT".
2 Connect the other end of this cable to the ANT 2 IN(CABLE) terminal on the back of
the TV.
ANT IN ANT OUT
Connecting to a Cable Box that Descrambles Some Channels
If your cable box descrambles only some channels (such as premium channels), follow the instructions below.
You will need a two-way splitter, an RF (AlB) switch and four lengths of Antenna cable. (These items are available
at most electronics stores.)
1 Find and disconnect the cable that is
connected to the ANT IN terminal on your
cable box.
)0>-
This terminal might be labeled "ANT IN",
"VHF IN" or simply, "IN".
2 Connect this cable to a two-way splitter.
------~-{J
cable Splitter
3 Connect an Antenna cable between an
OUTPUT terminal on the splitter and the IN
terminal on the cable box.
Incoming
cable
Splitter
Cable Box
Cable Box
4 Connect an Antenna cable between the
ANT OUT terminal on the cable box and the
B-IN terminal on the RF(AlB) switch.
1 - - l n · ~ ~ · ~ e · i n g - - : = [ I I [ ] S L . . p l ~ i t t e r " ' r ~-
r
omr~-'-,"--:Cc
. .
: ::-t£
- - : C 0 l l T ~ ) ~~~J
Switch
5 Connect another cable between the other
OUT terminal on the splitter and the A-IN
terminal on the RF (AlB) switch.
Incoming
cable
6 Connect the last Antenna cable between
the OUT terminal on the RF (AlB) switch
and the ANT 2 IN (CABLE) terminal on the
rear of the TV.
Incoming
cable
~
_ _ lVRear
~
" oa,
001
ro
~~ ~~o
'--d-~
,
0 ANT 2 IN (CABLE)
Splitter
,-=_ _ ~.
RF (AlB)
Switch
After you have made this connection, set the AlB switch to the "A" position for normal viewing. Set the AlB switch to the "B"
position to view scrambled channels. (When you set the AlB switch to "B", you will need to tune your TV to the cable box's
output channel, which is usually channel 3 or 4.)
I
Connecting Cable TV
To connect to a cable TV system, follow the instructions below.
Cable without a Cable Box
1 Plug the incoming cable into the ANT 2 IN(CABLE) terminal on the back of the TV.
)0>-
Because this TV is cable-ready, you do not need a cable box to view
unscrambled cable channels.
Connecting to a Cable Box that Descrambles All Channels
1 Find the cable that is connected to the ANT OUT terminal on your cable box.
)0>-
This terminal might be labeled "ANT OUT", "VHF OUT" or simply, "OUT".
2 Connect the other end of this cable to the ANT 2 IN(CABLE) terminal on the back of
the TV.
ANT IN ANT OUT
Connecting to a Cable Box that Descrambles Some Channels
If your cable box descrambles only some channels (such as premium channels), follow the instructions below.
You will need a two-way splitter, an RF (AlB) switch and four lengths of Antenna cable. (These items are available
at most electronics stores.)
1 Find and disconnect the cable that is
connected to the ANT IN terminal on your
cable box.
)0>-
This terminal might be labeled "ANT IN",
"VHF IN" or simply, "IN".
2 Connect this cable to a two-way splitter.
------~-{J
cable Splitter
3 Connect an Antenna cable between an
OUTPUT terminal on the splitter and the IN
terminal on the cable box.
Incoming
cable
Splitter
Cable Box
Cable Box
4 Connect an Antenna cable between the
ANT OUT terminal on the cable box and the
B-IN terminal on the RF(AlB) switch.
1 - - l n · ~ ~ · ~ e · i n g - - : = [ I I [ ] S L . . p l ~ i t t e r " ' r ~-
r
omr~-'-,"--:Cc
. .
: ::-t£
- - : C 0 l l T ~ ) ~~~J
Switch
5 Connect another cable between the other
OUT terminal on the splitter and the A-IN
terminal on the RF (AlB) switch.
Incoming
cable
6 Connect the last Antenna cable between
the OUT terminal on the RF (AlB) switch
and the ANT 2 IN (CABLE) terminal on the
rear of the TV.
Incoming
cable
~
_ _ lVRear
~
" oa,
001
ro
~~ ~~o
'--d-~
,
0 ANT 2 IN (CABLE)
Splitter
,-=_ _ ~.
RF (AlB)
Switch
After you have made this connection, set the AlB switch to the "A" position for normal viewing. Set the AlB switch to the "B"
position to view scrambled channels. (When you set the AlB switch to "B", you will need to tune your TV to the cable box's
output channel, which is usually channel 3 or 4.)