Setting Up Anynet; Scanning And Switching Between Anynet+ Devices - Samsung FP-T5084 Owner's Instructions Manual

The following settings help set the Anynet+ functions.
I
Setting Up Anynet+
To use the Anynet+ Function, Anynet+ (HDMI·CEC) must be set to On
1 Press the Anynet+ button.
Press the. or T button to select Setup, then press the ENTER button.
2 Press the ENTER button to select Anynet+ (HDMI·CEC), then press the
ENTER button.
3 Press the. or T button to select On, then press the ENTER button.
};>
The Anynet+ (HDMI-CEC) function is enabled.
};>
If you select Off, Anynet+ (HDMI-CEC) is disabled.
};>
When the Anynet+ (HDMI-CEC) function is disabled, all the Anynet+ related
operations are deactivated.
Setting an Anynet+ Device to turn Off Automatically when the TV is Turned Off
2 Press the. or T button to select Auto Turn Off, then press the ENTER button.
3 Press the. or T button to select On, then press the ENTER button.
};>
The Auto Turn Off function is enabled.
};>
If you select Off, the Auto Turn Off function is canceled.
Press the EXIT button to exit.
};>
The active source on the TV remote must be set to TV to use the Anynet+ function.
};>
If you set Auto Turn Off to On, connected external devices are also turned off when the TV is turned off.
If an external device is still recording, it mayor may not turn off.
};>
Anynet+ devices connected to the TV are listed.
2 Press the • or T button to select a particular device and press the ENTER button.
It is switched to the selected device.
3 If you cannot find a device you want, press the. or T button to select Searching
Connections, then press the ENTER button.
The message Configuring Anynet+ connection ... is displayed.
When searching devices complete, the connected devices are listed in the Anynet+
menu.
};>
Switching to the selected devices may take up to 2 minutes. You cannot cancel the
operation during the switching operation.
};>
The time required to scan for devices is determined by the number of connected
devices.
};>
When the device scan is complete, the number of devices found are not displayed.
};>
Although the TV automatically scans devices when it is turned on using the POWER button, devices connected when
the TV is already on are not displayed in the device list. In this case, select the Searching Connections menu to search
devices.
};>
If you have selected an external device by pressing the SOURCE button, you cannot use the Anynet+ function. Make
sure to switch to an external Anynet+ device by using the Anynet+ button.
Continued...
The following settings help set the Anynet+ functions.
I
Setting Up Anynet+
To use the Anynet+ Function, Anynet+ (HDMI·CEC) must be set to On
1 Press the Anynet+ button.
Press the. or T button to select Setup, then press the ENTER button.
2 Press the ENTER button to select Anynet+ (HDMI·CEC), then press the
ENTER button.
3 Press the. or T button to select On, then press the ENTER button.
};>
The Anynet+ (HDMI-CEC) function is enabled.
};>
If you select Off, Anynet+ (HDMI-CEC) is disabled.
};>
When the Anynet+ (HDMI-CEC) function is disabled, all the Anynet+ related
operations are deactivated.
Setting an Anynet+ Device to turn Off Automatically when the TV is Turned Off
2 Press the. or T button to select Auto Turn Off, then press the ENTER button.
3 Press the. or T button to select On, then press the ENTER button.
};>
The Auto Turn Off function is enabled.
};>
If you select Off, the Auto Turn Off function is canceled.
Press the EXIT button to exit.
};>
The active source on the TV remote must be set to TV to use the Anynet+ function.
};>
If you set Auto Turn Off to On, connected external devices are also turned off when the TV is turned off.
If an external device is still recording, it mayor may not turn off.
};>
Anynet+ devices connected to the TV are listed.
2 Press the • or T button to select a particular device and press the ENTER button.
It is switched to the selected device.
3 If you cannot find a device you want, press the. or T button to select Searching
Connections, then press the ENTER button.
The message Configuring Anynet+ connection ... is displayed.
When searching devices complete, the connected devices are listed in the Anynet+
menu.
};>
Switching to the selected devices may take up to 2 minutes. You cannot cancel the
operation during the switching operation.
};>
The time required to scan for devices is determined by the number of connected
devices.
};>
When the device scan is complete, the number of devices found are not displayed.
};>
Although the TV automatically scans devices when it is turned on using the POWER button, devices connected when
the TV is already on are not displayed in the device list. In this case, select the Searching Connections menu to search
devices.
};>
If you have selected an external device by pressing the SOURCE button, you cannot use the Anynet+ function. Make
sure to switch to an external Anynet+ device by using the Anynet+ button.
Continued...