Treadmill Operation - Horizon Fitness TREADMILL WT951 User Manual

TENSIONING THE RUNNING BELT
The running belt has been properly adjusted at the
factory before it was shipped. At times the belt can
move off-center during shipment.
CAUTION: Running belt should NOT be moving during
tensioning. Over-tightening the running belt can
cause excessive wear on the treadmill as well as its
components. Never over-tighten the belt.
If you can feel a slipping sensation when running on the
treadmill, the running belt must be tightened. In most
cases, the belt has stretched from use, causing the
belt to slip. This is a normal and common adjustment.
To eliminate this slipping, TURN THE TREADMILL OFF
and tension BOTH THE REAR ROLLER BOLTS using the
supplied Allen wrench, turning them 1/4 TURN to the
right as shown. Turn the treadmill on and check for
slipping. Repeat if necessary, but NEVER TURN the
roller bolts more than 1/4 turn at a time. Belt is properly
tensioned when the slipping sensation is gone.
Belt is too far to the right side
Belt is too far to the left side
1
WT951_Pedo_Treadmill_Rev.1.3.ind14-15 14-15
CENTERING THE RUNNING BELT
The running belt has been properly adjusted at the
factory before it was shipped. At times the belt can
move off-center during shipment. Before operating the
treadmill, make sure the belt is centered and remains
centered to maintain smooth operation.
CAUTION: Do not run belt faster than 1/2 mph while
centering. Keep fingers, hair and clothing away from
belt at all times.
If the running belt is too far to the right side:
With the treadmill running at 1/2 mph, turn the right
adjustment bolt clockwise 1/4 TURN at a time (using
the supplied Allen wrench). Check the belt alignment.
Allow belt to run a full cycle to gauge if more adjustment
is needed. Repeat if necessary, until the belt remains
centered during use.
If the running belt is too far to the left side:
With the treadmill running at 1/2 mph, turn the right
adjustment bolt counter-clockwise 1/4 TURN at a time
(using the supplied Allen wrench). Check the belt
alignment. Allow belt to run a full cycle to gauge if more
adjustment is needed. Repeat if necessary, until the
belt remains centered during use.
TREAD MIL L O PERATIO N
K L E A
INCLINE M A NUA L IN TERVALS
1,000 2,000 5,000
E NT ER
C H A N GE DI SP LAY
C D
H J
A) WIDESCREEN MONITOR DISPLAY: Speed, Time, Heart Rate, Distance, Incline, Calories and Program Profiles.
B) STOP: Press to pause/end your workout. Hold for 3 seconds to reset the treadmill.
C) START: Simply press to begin exercising or starts your program.
D) ENTER: Used to select Program, Level and Time. Press to change display feedback during workout, Hold to scan.
Also used to confirm SPEED/INCLINE keys.
E) INCLINE KEYS: Used to reach desired incline more quickly. Press before pressing ENTER to confirm.
F) SPEED KEYS: Used to reach desired speed more quickly. Press before pressing ENTER to confirm.
G) PROGRAM KEYS: Used to select from 7 preset programs.
H) INCLINE ARROW KEYS: Used to adjust incline in small increments (0.5% increments).
I) SPEED ARROW KEYS: Used to adjust speed in small increments (0.1 mph increments).
J) SAFETY KEY POSITION: Enables treadmill when safety key is inserted.
K) WATER BOTTLE / CD / MP HOLDERS: Holds personal workout equipment.
L) READING RACK: Holds reading material. (Remove sales sticker before use)
G F K
™
W EIG HT
SPEED
L O SS
10,000
B
I
15
9/15/06 1:03:05 PM