Horizon Fitness T901 User Manual page 6

ASSE MBLY ST E P 2
HARDWARE BAG 2 CONTENTS :
BOLT (D)
Qty: 1
LEAD WIRE
RIGHT CONSOLE MAST
CONSOLE CABLE
LOCK LATCH PIN (G)
ELEVATION FRAME
A Open HARDWARE BAG 2.
B Attach LOCK LATCH PIN (G) to RIGHT FOLDING
FRAME using T-wrench and tighten completely.
C Pull LEAD WIRE through RIGHT CONSOLE MAST. After pulling the lead wire through the mast, the top
of the console cable should be located at the top of the mast. Detach and discard lead wire.
D Insert 1 BOLT (D) and 1 FLAT WASHER (E) through RIGHT CONSOLE MAST followed by 1 WAVY WASHER
(F) and attach to MAIN FRAME.
E Unscrew PRE-ATTACHED NUT and remove from RIGHT LINKAGE ARM and discard. Carefully move
RIGHT LINKAGE ARM and PRE-ATTACHED TEFLON WASHER into position to attach to ELEVATION
FRAME.
F While holding RIGHT CONSOLE MAST in the upright position, attach RIGHT LINKAGE ARM using BOLT
(I) and TEFLON WASHER (J) as shown.
10
T901_Rev.2.0.indd 10-11
FLAT WASHER (E)
WAVY WASHER (F)
27 mm
29 mm
Qty: 1
Qty: 1
BOLT (I) TEFLON WASHER (J)
Qty: 1 Qty: 1
RIGHT CONSOLE MAST
WAVY WASHER (F)
TEFLON WASHER (J)
FLAT WASHER (E)
BOLT (I)
BOLT (D)
RIGHT LINKAGE ARM
PRE-ATTACHED BOLT
PRE-ATTACHED NUT PRE-ATTACHED TEFLON WASHER
ELEVATION FRAME
NOTE: Do not completely tighten any
screws or bolts until step 6 is complete!
ASSEMBLY STEP 
HARDWARE BAG  CONTENTS:
LOCK LATCH
PIN (G)
BOLT (K)
Qty: 1
20 mm
Qty: 6
RIGHT HANDLEBAR
FLAT WASHERS (L)
SPRING WASHERS (M)
BOLTS (K)
POWER CABLE
PULSE CABLE
CONSOLE CABLE
CABLE HOLE
RIGHT HANDLEBAR
RIGHT CONSOLE MAST
FLAT WASHER (L) SPRING WASHER (M)
8 mm 8 mm
Qty: 4 Qty: 6
A Open HARDWARE BAG .
B With the running deck in the
lowered position, place the
RIGHT HANDLEBAR on top of
the RIGHT CONSOLE MAST.
CONSOLE CABLE
Carefully route the CONSOLE
BOLTS (K)
CABLE through the bottom
SPRING WASHERS (M)
of the handlebar and out the
ARC WASHERS (N)
CABLE HOLE as shown in
second drawing below. The
PULSE CABLE and POWER
CABLE should be pulled out of
the hole as well.
CONSOLE MASTS
NOTE: Do not pinch the
CONSOLE CABLE when placing
right handlebar on top of the
RIGHT CONSOLE MAST.
C To assemble the RIGHT
HANDLEBAR to the RIGHT
CONSOLE MAST, insert
2 BOLTS (K), 2 SPRING
WASHERS (M) and 2 FLAT
WASHERS (L) in the inside
of the mast and 1 BOLT (K),
1 SPRING WASHER (M) and 1
ARC WASHER (N) in the rear
of the mast as shown.
D Repeat on other side.
NOTE: Only the pulse cable
will need to be routed through
the cable hole on the left
handlebar.
CONSOLE CABLE
NOTE: Do not completely
tighten any screws or bolts
NOTE: Carefully align holes
until step 6 is complete!
when assembling handlebars to
console mast, making sure to
not press down on handlebars.
ARC WASHER (N)
8 mm
Qty: 2
11
9/10/08 11:15:33 AM