Do you have a question about the PREMIER T1201 and is the answer not in the manual?
Questions and answers
Rosanne
March 7, 2025
error code - belt needs lube?
what type of lube and instructions to do this?
1 comments:
Mr. Anderson
March 7, 2025
The Horizon Fitness PREMIER T1201 treadmill requires a lubricant for the belt. The instructions for lubricating the belt are:
1. Unplug the power cord. 2. Apply the lubricant to the running deck. 3. Tighten both rear roller bolts to their original position, aligning with the marks. 4. Plug in the power cord and insert the safety key. 5. Start the treadmill and walk on the belt for two minutes to spread the lubricant. 6. Once lubrication is complete, reset the console by pressing and holding the ‘STOP’ and Speed ‘+’ buttons for five seconds.
For lubricating the air shocks, use a Teflon-based spray. For additional questions, contact Horizon Fitness.
Whether your goal is to win races or simply enjoy a fuller, healthier lifestyle, a Premier Series treadmill can help you attain it – adding club-quality performance to your at-home workouts, with the ergonomics and innovative features you need to get stronger and healthier, faster.
Failure to comply will void the warranty. • Do not use treadmill in any location that is not temperature controlled, such as but not limited to garages, porches, pool rooms, bathrooms, car ports or outdoors. Failure to comply may void the warranty.
If there is any play in these areas, the treadmill has not been properly assembled. To prevent damage to the treadmill, the assembly instructions must be reviewed and corrective actions should be taken.
P R E-ASS E MB LY Disassemble box and remove the cardboard packaging that is not beneath the treadmill. Do not attempt to lift the treadmill at this time. Remove plastic wrap from console masts. *NOTE: During each assembly step, ensure that ALL nuts and bolts are in place and partially threaded in before completely tightening any ONE bolt.
Page 6
ASSE MBLY ST E P HARDWARE BAG CONTENTS: BOLT (A) FLAT WASHER (B) 20 mm 8 mm Qty: 6 Qty: 4 RIGHT HANDLEBAR CONSOLE CABLE ARC WASHERS (D) SPRING WASHERS (C) BOLTS (A) BOLTS (A) SPRING WASHERS (C) FLAT WASHERS (B) CONSOLE MASTS POWER CABLE...
Page 7
SUPPORT BAR as shown. Repeat on the other side Connect power plug to the treadmill and connect the cord to a power outlet. The on/off switch is located next to the power cord. Flip this switch to the 'ON' position, so ON/OFF SWITCH that the switch is lit.
Your treadmill will not start unless the safety key is placed in position. Attach the clip end securely to your clothing. This safety key is designed to cut the power to the treadmill if you should fall. Check the operation of the safety key every 2 weeks.
START: Press start to begin exercising, starts your workout, or resume exercising after pause. the right adjustment bolt clockwise 1/4 TURN at STOP: Press to pause/end your workout. Hold for 3 seconds to reset the treadmill. a time (using the supplied Allen wrench). Check INCLINE the belt alignment.
Q U I C K STA RT Use this mode if you wish to begin working out immediately. Turn on the treadmill (the switch is located at the bottom-front of motor cover). Press START key and begin exercising. Program will automatically count time up from 0:00, the speed will default to 0.5 mph, and the incline will default to 0%.
2:00 USI NG iPod The Horizon Fitness iPod Docking Station is the entertainment solution for your workouts. Various models of iPod with a dock connector can fit with the use of the included inserts. Using your iPod Docking Station (iPod not included) Remove the RUBBER PLUG from bottom of the DOCKING STATION.
HOW HARD? (Intensity of Workouts) How hard you workout is also determined by your goals. If you use your treadmill to prepare for a 5K run, you will probably work out at a higher intensity than if your goal is general fitness. Regardless of your long term goals, always begin an exercise program at low intensity.
Page 13
TA RG E T HE A RT RAT E ZO NE CHA RT What is Target Heart Rate Zone? Target Heart Rate Zone tells you the number of times per minute your heart needs to beat to achieve a desired workout effect.
WHEN SHOULD I BE WORRIED ABOUT A NOISE? As long as the sounds your treadmill makes are no louder than a normal conversational tone of voice, it is considered normal noise.
• Inspect the power cord. If the power cord is damaged, contact Horizon Fitness. until calibration is complete. • Make sure the power cord is not underneath the treadmill or in any other area where it can become pinched or cut.
All repairs attempted by you on your fitness equipment are undertaken AT YOUR OWN RISK and Horizon Fitness shall have no liability for any ExCLUSIONS AND LIMITATIONS injury to the person or property arising from such repairs.
NOTE: Please read the TROUBLESHOOTING section before contacting Customer Tech Support. To receive additional product information, visit us at www.horizonfitness.com T1201. Rev. 1.7 2008 Horizon Fitness Products | Designed & Engineered in the U.S.A. | Made in China T1201_Rev.1.7.indd 32...
Need help?
Do you have a question about the PREMIER T1201 and is the answer not in the manual?
Questions and answers
error code - belt needs lube? what type of lube and instructions to do this?
The Horizon Fitness PREMIER T1201 treadmill requires a lubricant for the belt. The instructions for lubricating the belt are:
1. Unplug the power cord.
2. Apply the lubricant to the running deck.
3. Tighten both rear roller bolts to their original position, aligning with the marks.
4. Plug in the power cord and insert the safety key.
5. Start the treadmill and walk on the belt for two minutes to spread the lubricant.
6. Once lubrication is complete, reset the console by pressing and holding the ‘STOP’ and Speed ‘+’ buttons for five seconds.
For lubricating the air shocks, use a Teflon-based spray. For additional questions, contact Horizon Fitness.
This answer is automatically generated