Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Dell Manuals
  4. Server
  5. PowerEdge C410X
  6. Hardware owner's manual

Dell PowerEdge C410x Hardware Owner's Manual

Servers
Hide thumbs

Advertisement

Quick Links

Download this manual
Dell PowerEdge C410x
Hardware Owner's Manual

Advertisement

loading

  Also See for Dell PowerEdge C410x

Dell PowerEdge C410x Getting Started Manual
Dell PowerEdge C410x Getting Started Manual 123 pages
Dell PowerEdge B02S Hardware Owner's Manual
Dell PowerEdge B02S Hardware Owner's Manual 85 pages
Dell PowerEdge C410x Hardware Owner's Manual
Dell PowerEdge C410x Hardware Owner's Manual 65 pages

  Related Manuals for Dell PowerEdge C410x

  Summary of Contents for Dell PowerEdge C410x

  • Page 1 Dell PowerEdge C410x Hardware Owner’s Manual...

  • Page 2: Notes, Cautions, And Warnings

    Other trademarks and trade names may be used in this publication to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.

  • Page 3: Table Of Contents

    Contents NOTES, CAUTIONS, AND WARNINGS ........................1 CONTENTS ................................. 3 INTRODUCTION ............................6 ................................6 OWER EQUENCE GPGPU C ..........................10 UPPORTED ONFIGURATIONS GPGPU S ............................10 UPPORT IMITATION (IB) S ..........................10 NFINI UPPORT IMITATION ................................... 10 HECKLIST PRODUCT OVERVIEW ..........................11 ..............................
  • Page 4 Replacing Power Distribution Board (PDB) ......................52 Installing the power distribution board ....................... 58 ................................59 OARD Replacing iPass Board ............................59 Installing the iPass board ............................. 67 ................................68 IDDLE OARD Replacing Middle Board ............................68 Installing the system middle board ........................69 I/O P ................................
  • Page 5 —F ........................... 99 AFETY IRST OU AND YSTEM Checking GPU Card ............................100 Checking iPass Cable ............................100 Checking iPass Connector to Host System ......................101 Check if iPass Board (GS-IPASS2 / GS-IPASS3) is installed properly ..............101 JUMPERS AND CONNECTORS ........................102 C410X M ..................

  • Page 6: Introduction

    Introduction Power Sequence It is recommended that the following power sequence be followed when using the C410x and BMC 1.34 (or newer) with a host server not Intel E5-2600 Series based: For a single host server connected to a C410x: Power Up Sequence: Power up the C410x.
  • Page 7 Wait for the Green power LEDs on the individual PCI cages to light. Power up the host server. iii. Power Down Sequence: i. Power down the C410x. ii. Wait for the Green power LEDs on the individual PCI cages to turn off and the fans to turn off.
  • Page 8 Power down the C410x. iii. For multiple host servers connected to a C410x: Initial Power Up Sequence: Power up the C410x. Wait for the Green power LEDs on the individual PCI cages to light. iii. Wait for the Blue UID LED on the left ear tab to stop blinking and then turn off.
  • Page 9 Wait for the host server to power off. For multiple host servers connected to a C410x: Initial Power Up Sequence: Power up the C410x. Wait for the Green power LEDs on the individual PCI cages to light. iii. Wait for the Blue UID LED on the left ear tab to stop blinking and then turn off.

  • Page 10: Supported Gpgpu Configurations

    If more than one IB card is installed in a C410x and connected to a single host server issues may be observed. Checklist Carefully unpack the Dell PowerEdge C410X server and check that the following items were included. • One Dell PowerEdge C410X system •...

  • Page 11: Product Overview

    Product Overview A Tour of the System The following sections describe the external features of the Dell PowerEdge C410X server. System Front View Figure 1 – Front View Power LED/Button PCI Cage 5 System LED PCI Cage 6 UID LED/Button...
  • Page 12 Figure 2 – Back View Power Module 1 iPass connector 6 Power Module 2 iPass connector 7 Power Module 3 iPass connector 8 Power Module 4 PCI Cage 11 BMC LAN Cable PCI Cage 12 iPass connector 1 PCI Cage 13 iPass connector 2 PCI Cage 14 iPass connector 3...

  • Page 13: System Leds Description

    System LEDs Description Front System LEDs The front system LEDs contain System LED, Power LED and UID LED information. The detailed LEDs information is listed below: Figure 3 – Front System LEDs Table 1-1. Front System LEDs System LED Displays status/errors and is controlled by BMC. Color Condition Occurrence...

  • Page 14: Static / Dynamic Ip Switch Function Instruction

    Static / Dynamic IP Switch Function Instruction  To switch from DHCP to static or vice versa:  Hold down the ID button for 5 seconds  While pressing the ID button, press and hold the power button for 5 seconds ...

  • Page 15: Removing And Installing Hardware

    Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.
  • Page 16 Removing and Installing Hardware | 16...
  • Page 17 2. Remove the middle top cover from the system. 3. Loosen and remove the screws securing the back cover. Removing and Installing Hardware | 17...

  • Page 18: Installing The System Cover

    4. Slide the cover horizontally to the back using the traction pad and remove the back cover in the direction of the arrow. NOTE: This system must be operated with the system cover installed to ensure proper cooling. Installing the system cover To install the system cover follow the instructions for removing the system cover in the reverse order.

  • Page 19: Pci Cage

    PCI Cage Removing the PCI Cage NOTE: • Take note of the drive tray orientation before sliding it out. • The tray will not fit back into the bay if inserted incorrectly. 1. Lift the release lever and pull on the cage handle at the same time. 2.

  • Page 20: Installing The Pci Cage

    Installing the PCI cage To install the PCI cage follow the instructions for removing the PCI cage in the reverse order. PCIe Card Replacing PCIe Card CAUTION: Before you remove or install the PCIe card, press PCI cage power button to turn off the specific single PCI cage power before replacing PCIe card.

  • Page 21: Installing The M1060 Card

    3. Secure the card in place with screws and place the PCI side cover as shown in the illustration. 4. Secure the PCI side cover and back cover in place with screws. Installing the M1060 card To install the M1060 card follow the instructions for removing the M1060 card in the reverse order. Removing and Installing Hardware | 21...
  • Page 22 For M2050/M2070/M2070Q/M2075/M2090 Cards 1. Connect PCI power cable. 2. Insert the PCIe card by 45 degree and push it into the socket vertically. CAUTION: Care should be taken to prevent damage to components on the back side of the PCIe card. Make sure the card does not drag across the card mounting standoffs of the cage when inserting the card into the socket.
  • Page 23 5. Connect power cable to card as shown. 6. Replace the side cover. 7. Secure the side cover with 4 screws. Removing and Installing Hardware | 23...
  • Page 24 8. Secure the PCIE side cover with 3 screws as illustration arrow show. Removing and Installing Hardware | 24...

  • Page 25: Installing The Intel 5110P Card

    Installing the Intel 5110P Card Follow the instructions to install the Intel 5110P card. 1. Attach two support brackets with screws to the 5110P card heatsink cover. Screw 2/4 Support Bracket 3 Support Bracket 1 Removing and Installing Hardware | 25...
  • Page 26 Connect power cable to card as shown. CAUTION: Make sure the power cable is plugged before inserting the PCIe card into socket. 3. Insert the 5110P card into the socket as shown in the illustration. CAUTION: Care should be taken to prevent damage to components on the back side of the PCIe card. Make sure the card does not drag across the card mounting standoffs of the cage when inserting the card into the socket.
  • Page 27 4. Secure the 511P card with 3 screws. Screw 7 Screw 8 Removing and Installing Hardware | 27...

  • Page 28: Removing The 5110P Card

    Removing the 5110P card Follow the instructions to remove the Intel 5110P card. Remove the 3 securing screws. Remove the 5110P card from the socket. CAUTION: Care should be taken to prevent damage to components on the back side of the PCIe card. Make sure the card does not drag across the card mounting standoffs of the cage when removing the card from the socket.
  • Page 29 Remove the securing screws and the support bracket from the 5110P heatsink cover. Removing and Installing Hardware | 29...

  • Page 30: Installing The Nvidia K10/K20 Card

    Installing the NVIDIA K10/K20 Card Follow the instructions to install the NVIDIA K10/K20 card. 1. Remove the 5 securing screws of K10 heatsink top cover. Remove the 8 securing screws of K20 heatsink top cover. NOTE: Please keep heatsink top cover and securing screws. The heatsink top cover should be attached to replaced card before returning.
  • Page 31 2. Attach the support bracket with two screws to the K10/K20 card. Screw 2 3. Insert the K10/K20 card into the socket as shown in the illustration. CAUTION: Care should be taken to prevent damage to components on the back side of the PCIe card. Make sure the card does not drag across the card mounting standoffs of the cage when inserting the card into the socket.
  • Page 32 4. Secure the K10/K20 card with 3 screws. Screw 4 (Same as Screw 2) Screw 5 Removing and Installing Hardware | 32...
  • Page 33 5. Attach K10 support bracket. NOTE: Use the right mounting holes to secure the mounting bracket for the K10 card. Attach the K20 support bracket. NOTE: Use the left mounting holes to secure the mounting bracket for the K20 card. NOTE: Picture is showing a K10 card for a K20 installation.
  • Page 34 6. Secure the K10 support bracket with 3 screws. Secure the K20 support bracket with 3 screws. NOTE: Picture is showing a K10 card for a K20 installation. Screw 7 (Same as Screw 2) Screw 8 Removing and Installing Hardware | 34...
  • Page 35 7. Connect power cable to card. Removing and Installing Hardware | 35...

  • Page 36: Removing The Nvidia K10/K20 Card

    Removing the NVIDIA K10/K20 Card Follow the instructions to remove the NVIDIA K10/20 card. 1. Unplug power cable as shown. 2. Remove the K10 3 securing screws. Remove the K20 3 securing screws. Removing and Installing Hardware | 36...
  • Page 37 3. Remove the K10 support bracket. Remove the K20 support bracket. Removing and Installing Hardware | 37...
  • Page 38 4. Remove the 3 securing screws. 5. Remove the card from the socket. CAUTION: Care should be taken to prevent damage to components on the back side of the PCIe card. Make sure the card does not drag across the card mounting standoffs of the cage when removing the card from the socket. Removing and Installing Hardware | 38...
  • Page 39 6. Remove the securing screws and the support bracket from K10/K20 card. 7. Attach the heatsink top cover to the K10 card and secure with 5 screws. NOTE: The heatsink top cover must be assembled to the K10 card before it is returned for replacement.
  • Page 40 Attach the heatsink top cover to the K20 card and secure with 8 screws. NOTE: The heatsink top cover must be assembled to the K20 card before it is returned for replacement. Removing and Installing Hardware | 40...

  • Page 41: Replacing System Fans

    Replacing System Fans In case of system fan failure, you can quickly replace the system fan. CAUTION: Before you remove or install the system fans, take the steps: 1) Make sure the system is not turned on or connected to the AC power. 2) Disconnect all necessary cable connections.
  • Page 42 2. Remove the middle top cover from the system. 3. Lift the system fan ears. Removing and Installing Hardware | 42...

  • Page 43: Installing The System Fans

    4. Lift the system fan out of the system fan cage. Installing the system fans To install the system fans follow the instructions for removing the system fans in the reverse order. Removing and Installing Hardware | 43...

  • Page 44: Fan Cage

    Fan cage Replacing System Fan Cage CAUTION: Before you remove or install the system fan cage, take the steps: 1) Make sure the system is not turned on or connected to the AC power. 2) Disconnect all necessary cable connections. Failure to observe these warnings could result in personal injury or damage to the equipment.
  • Page 45 2. Remove the middle top cover from the system. 3. Loosen and remove the screws securing the fan cage. Removing and Installing Hardware | 45...
  • Page 46 4. Lift the fan cage out of the system. NOTE: Watch the fan status LED cables as the fan cage is lifted out of the system. The fan status LED connector should be unplugged before removing the fan cage completely from the system. Removing and Installing Hardware | 46...
  • Page 47 5. Remove the fans from the fan cage. Removing and Installing Hardware | 47...

  • Page 48: Installing The System Fan Cage

    6. Loosen and remove the screws on top of the system fan cage. Installing the system fan cage To install the system fan cage follow the instructions for removing the system fan cage in the reverse order. Removing and Installing Hardware | 48...

  • Page 49: Power Supply

    Power supply Replacing Power Supplies In case of a power supply failure, you can quickly replace the power supply unit. Follow these instructions to remove the power supply: CAUTION: In order to reduce the risk of injury from electric shock, disconnect AC power from the power supply before removing it from the system.
  • Page 50 2. Press the retaining clip on the right side of the power supply along the direction of the arrow. 3. At the same time, pull out the power supply by using its handle. NOTE: It takes considerable force to remove the power supply. Removing and Installing Hardware | 50...
  • Page 51 Follow these instructions to install the power supply: Insert the replacement power supply firmly into the bay. The retaining clip should snap. Fold the power supply handle down. Connect the AC power cord to the replaced power supply. Removing and Installing Hardware | 51...

  • Page 52: Power Distribution Board (Pdb)

    Power Distribution Board (PDB) Replacing Power Distribution Board (PDB) Follow these instructions to remove the PDB: CAUTION: Before you remove or install the power distribution board take the steps: 1) Make sure the system is not turned on or connected to the AC power. 2) Disconnect all necessary cable connections.
  • Page 53 3. Remove the middle top cover from the system. 4. Loosen and remove the screws securing the back cover. Removing and Installing Hardware | 53...
  • Page 54 5. Slide the cover horizontally to the back using the traction pad and remove the back cover in the direction of the arrow. 6. Then Remove the BMC LAN cable from the retention clip. Lay the BMC LAN cable across the fans out of the way.
  • Page 55 7. Loosen and remove the screws securing the power supply cage. 8. Slide the power cage horizontally to the back. Removing and Installing Hardware | 55...
  • Page 56 9. Lift the power cage to remove it in the direction of the arrow. 10. Loosen and remove the screw securing the rail. Removing and Installing Hardware | 56...
  • Page 57 11. Remove the rail by lifting the retention clip and at the same time slide the rail in the direction of the arrow. 12. Loosen and remove the screws securing the PDB. Removing and Installing Hardware | 57...

  • Page 58: Installing The Power Distribution Board

    13. Remove the PDB in the direction of the arrow. NOTE: It takes considerable force to remove the PDB. Installing the power distribution board To install the power distribution board follow the instructions for removing the power distribution board in the reverse order.

  • Page 59: Ipass Board

    iPass Board Replacing iPass Board Follow these instructions to replace the iPass board: CAUTION: Before you remove or install the iPass Board, take the steps: 1) Make sure the system is not turned on or connected to the AC power.2) Disconnect all necessary cable connections.
  • Page 60 2. Remove the middle top cover from the system. 3. Loosen and remove the screws securing the back cover. Removing and Installing Hardware | 60...
  • Page 61 4. Slide the cover horizontally to the back using the traction pad and remove the back cover in the direction of the arrow. 5. Then Remove the BMC LAN cable from the retention clip. Lay the BMC LAN cable across the fans out of the way.
  • Page 62 6. Pull up the power supply handle. 7. Remove the power supply in the direction of the arrow. Removing and Installing Hardware | 62...
  • Page 63 8. Loosen and remove the screws securing the power supply cage. 9. Slide the power cage horizontally to the back. Removing and Installing Hardware | 63...
  • Page 64 10. Lift the power cage to remove it in the direction of the arrow. 11. Loosen and remove the screws securing the top of the iPass connector cage. Removing and Installing Hardware | 64...
  • Page 65 12. Slide the iPass connector cage horizontally to the back. 13. Loosen and remove the screws securing the top iPass board. Removing and Installing Hardware | 65...
  • Page 66 14. Lift up the iPass board and remove it from the system. 15. Loosen and remove the screws securing the bottom iPass board. Removing and Installing Hardware | 66...

  • Page 67: Installing The Ipass Board

    16. Lift up the iPass board and remove it from the system. Installing the iPass board To install the iPass board follow the instructions for removing the iPass board in the reverse order. Removing and Installing Hardware | 67...

  • Page 68: Middle Board

    Middle Board Replacing Middle Board Follow these instructions to replace the middle board: CAUTION: Before you remove or install the middle board, take the steps: 1) Make sure the system is not turned on or connected to the AC power. 2) Disconnect all necessary cable connections.

  • Page 69: Installing The System Middle Board

    5. Lift the middle board out of the system in the direction of the arrow, front edge first , to clear the IO ports. Installing the system middle board To install the system middle board follow the instructions for removing the system middle board in the reverse order.

  • Page 70: Front I/O Panel

    Front I/O Panel Removing Front I/O Panel CAUTION: Before you remove or install the Front I/O Panel, make sure the system is not turned on or connected to the AC power. 1. Remove the screws securing the Front I/O panel cover. 2.

  • Page 71: Installing The Front Io Panel

    3. Remove the screws securing the Front I/O panel. 4. Remove the Front I/O panel and disconnect the cable. Installing the Front IO panel To install the Front IO panel follow the instructions for removing the Front IO panel in the reverse order. Removing and Installing Hardware | 71...

  • Page 72: Installing The Rail And The System

    Installing the Rail and the System Follow these instructions to install the rail into a rack: 1. Install the sliding rails into the rack. 2. Align the inner rails with the sliding rails of the rack. Removing and Installing Hardware | 72...
  • Page 73 3. Push the system into the sliding rails until the locking latch clicks into place. 4. Connect ipass connectors and power connectors. Removing and Installing Hardware | 73...
  • Page 74 NOTE: The 1400W Power Supplies require 220VAC. Removing and Installing Hardware | 74...

  • Page 75: Cable Routings

    Cable Routings Fan Power Cable Front I/O Cable BMC LAN Cable Fan LED Cable PCI Power Cable Switch Cable Cable Routings | 75...

  • Page 76: Ipass Port Mapping

    iPass Port Mapping 2 to 1 mode 4 to 1 mode 8 to 1 mode IPASS PCIE IPASS PCIE IPASS PCIE Mapping1 1,15 1,2,15,16 1,2,3,4,13,14,15,16 2,16 Mapping2 3,13 3,4,13,14 4,14 Mapping3 5,11 5,6,11,12 5,6,7,8,9,10,11,12 6,12 Mapping4 7,8,9,10 8,10 NOTE: The default port mapping is 2 to 1 mode. Cable Routings | 76...

  • Page 77: Bmc Remote Management Console

    Initial Configuration using a DHCP Server Before entering the Dell Remote Management Console, you need to connect the DHCP server in the subnet to which it is physically connected. If a DHCP server is found, it may provide a valid IP address, gateway address and net mask.

  • Page 78: Static/Dhcp Ip Controlled By Front Panel Button

    Static/DHCP IP Controlled by Front Panel Button  To switch from DHCP to static or vice versa:  Hold down the ID button for 5 seconds  While pressing the ID button, press and hold the power button for 5 seconds ...

  • Page 79: Remote Management Console Overview

    Remote Management Console Overview Open a web browser and type in your identified IP. The IP address can be found using your DHCP server. A dialog box prompts you to enter Username and Password. Enter the following values: Username: root Password: root NOTE: The default user name and password are in lower-case characters.

  • Page 80: Enter Dell Remote Management Console

    Enter Dell Remote Management Console After you successfully log in to your Dell Remote Management Console, the Remote Management Console GUI appears. Properties Properties displays the firmware version of current remote client system. BMC Remote Management Console | 80...

  • Page 81: Configuration

    Configuration Network You can view and modify the network settings on this screen. Select whether to obtain an IP address automatically or configure one manually. It is recommended to use DHCP if your environment has a DHCP server. You can set DHCP (obtain the IP address automatically) or STATIC IP (configure the IP address manually).

  • Page 82: Security

    Security Security shows the current certificate status. To generate a new certificate, click Generate Certificate. To upload a certificate, click Upload Certificate. BMC Remote Management Console | 82...

  • Page 83: Users

    Users To configure a specific user, click the Users ID. To display new user information, click Refresh. Please note that BMC convention for enabling an 'anonymous' login is to configure the entry for User ID 1 with a null username (all zero’s) and a null password (all zero’s). Applications may then present this to the user as an anonymous login.

  • Page 84: Services

    Services You can configure the web server parameters (such as, HTTP Port Number, HTTPS Port Number, and Timeout) on a remote computer. By default, the timeout is 1800 seconds; 5 for the Max Sessions and 1 for the Active Sessions. When you finish the configuration, click Apply Changes.

  • Page 85: Ipmi

    IPMI This screen contains two sections: IPMI Serial and IPMI Settings. IPMI Serial There are three serial configuration in IPMI Serial: Connection Mode Settings, Baud Rate, and Channel Privilege Level Limit. The Connection Mode Settings allows user to select the Console redirection type and to manage the system from a remote location.
  • Page 86 IPMI Settings IPMI Settings provides remote configuration over LAN. To activate IPMI remote configuration by LAN, check Enable IPMI Over LAN option, define the Channel Privilege Level Limit, and enter the Encryption Key. When you finish the configuration, click Apply Changes. BMC Remote Management Console | 86...

  • Page 87: Sessions

    Sessions This screen displays information on Active Sessions. Additionally, the trash can icon provides the delete function for privileged users. Click Refresh to refresh the Sessions status. BMC Remote Management Console | 87...

  • Page 88: Updates

    Updates The firmware can be updated remotely. To update firmware, follow the instruction below: 1. Select the file on your local system using Browse. 2. Select Update Type. 3. Select Preserve Configuration. 4. Click Update to delete the current version and update to the new version. NOTE: BMC firmware update should not be interrupted, any interruption may result unrecoverable firmware crash? ROM replacement is required to bring C410x back.

  • Page 89: Utilities

    Utilities Utilities provides BMC reboot and Factory default restore functions. To reboot system, click Reboot. To restore factory default, click Factory Default. BMC Remote Management Console | 89...

  • Page 90: Server Information

    Server Information Power Control The Power Control allows you to power on/off/cycle the remote host system. Additionally you can see the remote power status. To perform the power control operation, select the operation and click Apply Changes. BMC Remote Management Console | 90...

  • Page 91: Power Consumption

    Power Consumption This screen displays information on the system power consumption. The information includes Current Power Consumption, Power Consumption Monitoring Start Date, Max/Min Power Consumption, and Average Power Consumption. BMC Remote Management Console | 91...

  • Page 92: Gpu Power Consumption

    GPU Power Consumption This screen displays the status of GPU power consumption. Each sensor displays different color to indicate the health status of a specified GPU device. The green color indicates the device is healthy and there’s no sensor that has any alert. The yellow color indicates the device has at least one sensor that has warning alert.

  • Page 93: Thermal

    Thermal This screen displays the Fans and Temperatures sensors of a remote host system. Click Refresh to update current health status for both Fans and Temperatures. The green color indicates the device is healthy and there’s no sensor that has any alert. The yellow color indicates the device has at least one sensor that has a warning alert.

  • Page 94: System Event Log

    System Event Log System Event Log: It records the event when sensor has an abnormal state. When the log matches the pre-defined alert, the system sends out the notification automatically, if it is pre-configured. BMC Remote Management Console | 94...

  • Page 95: Platform Events

    Platform Events A platform event filter (PEF) can trigger an action and generate an alert when a critical hardware-related event occurs. For each PEF, you can choose the action to be taken when a platform event occurs. You can also choose to generate and send an alert when a platform event occurs. In the Platform Events screen, you can enable the generation of platform event alerts globally by clicking Global Alerting Enable.

  • Page 96: Traps Settings

    Traps Settings In the Trap Settings, user can set the IPv4 and Ipv6 Destination List. IPv6 and IPv4 are two completely separate protocols. IPv6 is not backwards compatible with IPv4, and IPv4 hosts and routers will not be able to deal directly with IPv6 traffic. IPv6 has a significantly larger address space than IPv4.

  • Page 97: Email Settings

    Email Settings If you want the alert to be sent by email, you can configure to specify the e-mail address, subject and message in the Email Settings. After you finish the configuration, click Apply Change to save the settings. BMC Remote Management Console | 97...

  • Page 98: Port Map

    Port Map User can identify the specified iPASS mapping to PCIE controller in Port Map. Click Apply Change to save the settings. BMC Remote Management Console | 98...

  • Page 99: Troubleshooting Your System

    Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

  • Page 100: Checking Gpu Card

    Checking GPU Card 1. Power off and remove the middle cover. See section-Removing System Cover to remove the middle cover. 2. Power on the system and PCIe device and check if the GPU card LED lights. 3. If not, see Check iPass cable. Checking iPass Cable 1.

  • Page 101: Checking Ipass Connector To Host System

    Checking iPass Connector to Host System 1. Check the Board to Board (BTB) connectors to the iPass Boards. 2. Check System SMBus device routing table. IPASS TOP IPASS Bottom iPass 1: Slot 1/15 iPass 5: Slot 2/16 iPass 2: Slot 3/13 iPass 6: Slot 4/14 iPass 3:...

  • Page 102: Jumpers And Connectors

    Jumpers and Connectors Dell PowerEdge C410X Middle Board Connectors and Jumpers Figure 5 identifies critical components on the Dell PowerEdge C410X middle board. Figure 5 – Middle Board Connectors and Jumpers Item Component PCI-E connectors PCI-E connectors Power connectors iPass board connectors...

  • Page 103: Getting Help

    Dell product catalog. Dell provides several online and telephone-based support and service options. Availability varies by country and product, and some services may not be available in your area. To contact Dell for sales, technical support, or customer service issues: 1.

  • Page 104: Index

    I/O removing, 46 system cover, 8 front view, 2 system event log, 72 getting help system fans, 17 contacting Dell, 82 system fans cages, 20 GPU power consumption, 70 system LEDs initial configuration via DHCP server, 53 front, 4...