Creda SPA 200c Installation And User Manual
Creda SPA 200c Installation And User Manual

Creda SPA 200c Installation And User Manual

Electric shower

Advertisement

HOW TO USE YOUR SPA200C SHOWER (SUMMARY)
1. Ensure the electricity and water are turned on to the unit.
2. Press the start / stop button "B".
This will turn the shower on, the water will flow and the
neon indicator light will illuminate. It is recommended that
you do not wholly enter the water flow during this period.
3. Knob "A" controls the power selection.
Select "High", "Medium (Med)" or "Cold"
The "small bar" indicates knob setting.
4. If the water is not at your desired showering
temperature, turn knob "C" a small amount until
you reach the desired showering temperature.
Turn clockwise for cooler or Turn anti-clockwise for warmer.
5. When you have finished showering, press the start / stop button "B" again.
The water will stop flowing and the neon indicator will go out.
10.5kW Models Only-Water will continue to flow for approximately 7 seconds before switching off.
6. Switch off the electricity supply at the ceiling switch or local isolator.
Notes
Wait 20 seconds for the temperature to stabilise after each adjustment.
The neon indicator light illuminates when the heaters are on and, if the shower has
been recently used, it may take up to 20 seconds to come on.
During this time the water may go from very hot to cold before stabilising.
The position of knob "C" will be approximately the same each time the shower is
used, varying only with incoming water temperature or pressure changes
(e.g. you will only need to change from summer to winter).
During normal operation, if an overheated water temperature is sensed then the
heater will switch off and the neon indicator light will go out.
Water will continue to flow and cool down before the heater switches back on again.
IMPORTANT WARNINGS!
DO NOT SWITCH THE APPLIANCE ON IF YOU SUSPECT IT OF BEING FROZEN.
WAIT UNTIL YOU ARE SURE IT HAS THAWED OUT.
DO NOT OPERATE THE APPLIANCE IF WATER DISCHARGES FROM THE PRESSURE RELIEF
VALVE. MAINTENANCE IS REQUIRED BEFORE THE APPLIANCE CAN BE SAFELY USED.
THIS APPLIANCE IS NOT INTENDED FOR USE BY PERSONS (INCLUDING CHILDREN AND
THE INFIRM) WITH REDUCED PHYSICAL, SENSORY OR MENTAL CAPABILITIES,
OR LACK OF EXPERIENCE AND KNOWLEDGE, UNLESS THEY HAVE BEEN GIVEN
SUPERVISION OR INSTRUCTION CONCERNING USE OF THE APPLIANCE
BY A PERSON RESPONSIBLE FOR THEIR SAFETY.
CHILDREN SHOULD BE SUPERVISED TO ENSURE THAT THEY
DO NOT PLAY WITH THE APPLIANCE.
We offer a technical advisory service on the telephone to installers and
other customers with problems in the field. RING 0844 372 7766 (UK ONLY)
(A3) Leaflet No. 567-2151-61b
16
CREDA SPA200C RANGE
ELECTRIC SHOWER
Installation and User Guide
IMPORTANT:
This booklet should be left with the user
after installation and demonstration

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SPA 200c and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Creda SPA 200c

  • Page 1 Water will continue to flow and cool down before the heater switches back on again. IMPORTANT WARNINGS! CREDA SPA200C RANGE DO NOT SWITCH THE APPLIANCE ON IF YOU SUSPECT IT OF BEING FROZEN. WAIT UNTIL YOU ARE SURE IT HAS THAWED OUT.
  • Page 2: Table Of Contents

    Creda After Sales Service ........
  • Page 3: Introduction

    INTRODUCTION 1. Water is heated instantaneously as it flows Thank you for purchasing a quality Creda SPA200C Shower manufactured in England. over the heating elements in the copper To enjoy your new shower at its best, please take time to read this manual thoroughly to cylinder (Diagram 8).
  • Page 4: How To Install Your Spa200C Shower

    HOW TO INSTALL YOUR SPA200C SHOWER WHAT TO DO IF THINGS GO WRONG (2) WARNING: ALL WIRING AND INSTALLATION MUST BE PROFESSIONAL SERVICE SUPERVISED BY A SUITABLY QUALIFIED PERSON. If the previous “Self Help” checks fail to restore the performance, you should seek professional help. WARNING: DO NOT INSTALL THIS SHOWER WHERE IT MAY BE SUBJECTED TO FREEZING CONDITIONS The person who installed the shower is probably the best one to investigate and correct it and is...
  • Page 5 Note: You may be charged for a service call if it is due to incorrect installation. leaflet. 7. The shower is designed to have an open outlet and should only be used with “Creda” recommended fittings. The model and serial number are located on the bottom face of the shower.
  • Page 6: Cold Water Inlet Pipe Configuration

    Curtain and Rail Pack with Handset Cat No. 93597862 Non-Slip Mat Cat No. 83792811 Height Adjuster Cat No. 93597861 Additional accessories and spare parts can be supplied against any Credit or Debit cards from Creda Sales Hotline 0844 372 7750...
  • Page 7 c) ELECTRICAL HOW TO USE YOUR SPA200C SHOWER (DETAILED) WARNING: THIS SHOWER MUST BE EARTHED. Ensure the electricity and water are turned on to the unit. The electrical installation must be in accordance with the current BS.7671 (IEE Wiring Regulations) and “Part P”...
  • Page 8: Assembly Of Accessories

    5. Re-fit the detachable bottom section with the two screws if it was removed. ASSEMBLY OF ACCESSORIES Diagram 5 - Riser Rail and Soap Dish Fitting Instructions (Refer to the separate fitting instruction sheet packed with the accessories for more details) 1.

Table of Contents