Creda JETSPA CONTEMPORARY Installation And User Manual
Creda JETSPA CONTEMPORARY Installation And User Manual

Creda JETSPA CONTEMPORARY Installation And User Manual

Electric shower

Advertisement

HOW TO USE YOUR JETSPA SHOWER (SUMMARY)
1. Ensure the electricity and water are turned on to the unit.
2. Your shower can be turned on by pressing either
Button "A", Button "B" or Button "C"
Button "A" (III) - Starts shower on "High" power.
Button "B" (II) - Starts shower on "Medium" power.
Button "C" (I) - Starts shower on "Cold".
Press Button "A", "B" or "C".
Water will flow and the LED indicator above your choice
will illuminate. It is recommended that you do not wholly
enter the water flow during this period.
3. If the water is not at your desired showering temperature,
turn knob "E" a small amount until you
reach the desired showering temperature.
Turn clockwise for cooler or Turn anti-clockwise for warmer.
4. When you have finished showering, press Button "D" ( ) only, the LED light above will flash.
Water will continue to flow for up to 7 seconds before switching off.
5. Switch off the electricity supply at the ceiling switch or local isolator.
Notes
Wait 20 seconds for the temperature to stabilise after each adjustment.
The LED indicator light illuminates when the heaters are on and, if the shower has
been recently used, can take up to 20 seconds to come on.
During this time the water may go from very hot to cold before stabilising.
The position of knob "E" will be approximately the same each time the shower is
used, varying only with incoming water temperature or pressure changes
(e.g. you will only need to change from summer to winter).
During normal operation, if an overheated water temperature is sensed then the
heater will switch off and the LED indicator light will go out.
Water will continue to flow and cool down before the heater switches back on again.
IMPORTANT WARNINGS!
DO NOT SWITCH THE APPLIANCE ON IF YOU SUSPECT IT OF BEING FROZEN.
WAIT UNTIL YOU ARE SURE IT HAS THAWED OUT.
DO NOT OPERATE THE APPLIANCE IF WATER DISCHARGES FROM THE PRESSURE RELIEF
VALVE. MAINTENANCE IS REQUIRED BEFORE THE APPLIANCE CAN BE SAFELY USED.
THIS APPLIANCE IS NOT INTENDED FOR USE BY PERSONS (INCLUDING CHILDREN AND
THE INFIRM) WITH REDUCED PHYSICAL, SENSORY OR MENTAL CAPABILITIES,
OR LACK OF EXPERIENCE AND KNOWLEDGE, UNLESS THEY HAVE BEEN GIVEN
SUPERVISION OR INSTRUCTION CONCERNING USE OF THE APPLIANCE
BY A PERSON RESPONSIBLE FOR THEIR SAFETY.
CHILDREN SHOULD BE SUPERVISED TO ENSURE THAT THEY
DO NOT PLAY WITH THE APPLIANCE.
We offer a technical advisory service on the telephone to installers and
other customers with problems in the field. RING 0870 9000 430 (UK ONLY)
(A3) Leaflet No. 567-2189-01 Revision A
12
JETSPA CONTEMPORARY
ELECTRIC SHOWER
Installation and User Guide
IMPORTANT:
This booklet should be left with the user
after installation and demonstration

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the JETSPA CONTEMPORARY and is the answer not in the manual?

Questions and answers

Summary of Contents for Creda JETSPA CONTEMPORARY

  • Page 1 Water will continue to flow and cool down before the heater switches back on again. IMPORTANT WARNINGS! JETSPA CONTEMPORARY DO NOT SWITCH THE APPLIANCE ON IF YOU SUSPECT IT OF BEING FROZEN. WAIT UNTIL YOU ARE SURE IT HAS THAWED OUT.
  • Page 2: Table Of Contents

    Note: You may be charged for a service call if you do not have the serial number. Creda After Sales Service ... . . How to maintain your Jet Spa Shower ..
  • Page 3: How To Install Your Jetspa Shower

    HOW YOUR JETSPA SHOWER WORKS HOW TO INSTALL YOUR JETSPA SHOWER WARNING: ALL WIRING AND INSTALLATION MUST BE 1. Water is heated instantaneously as it flows SUPERVISED BY A SUITABLY QUALIFIED PERSON. over the heating elements in the copper cylinder (Diagram 6). WARNING: DO NOT INSTALL THIS SHOWER WHERE IT MAY BE 2.
  • Page 4 Undo headworks of stabiliser valve. Check stabiliser is in place and remove any debris in valve then re-assemble. 7. The shower is designed to have an open outlet and should only be used with “Creda” recommended Water discharges Check for cause of high pressure and remove it.
  • Page 5: Cold Water Inlet Pipe Configuration

    COLD WATER INLET PIPE CONFIGURATION HOW TO USE YOUR JETSPA SHOWER (DETAILED) Please note that standard compression fittings are shown. 1. Ensure the electricity and water are turned on to the unit. Push-Fit connections or a combination of the two are also suitable. 2.
  • Page 6: Assembly Of Accessories

    IMPORTANT: Ensure you connect the flying lead from PCB to the front cover. against any Credit or Debit cards from Creda Sales Hotline 0870 9000 420 6. Re-fit the front cover, and secure by replacing the top and bottom fastening screws.

This manual is also suitable for:

Advantage 550Advantage 550c

Table of Contents