Table Of Contents - Comtech EF Data Vipersat CDM-570 User Manual

General
How to Use This Manual . . . . . . . . . . . 1-1
Manual Organization . . . . . . . . . . . . 1-1
Chapter 1 - General . . . . . . . . . 1-1
Chapter 2 - Quick Start Configuration 1-1
Chapter 3 - Using the Command Line
Interface (CLI) . . . . . . . . . . . . 1-2
Appendix A - Network Addressing . . 1-2
Appendix B - Automatic Switching . . 1-2
Appendix C - Dynamic Power Control1-2
Appendix D - Network Migration . . . 1-2
Appendix E - Glossary . . . . . . . . 1-2
Conventions and References . . . . . . . . 1-2
Product Description . . . . . . . . . . . . . . 1-4
Introduction . . . . . . . . . . . . . . . 1-4
Modem Features. . . . . . . . . . . . . 1-4
Router Features . . . . . . . . . . . . . 1-4
Network and Bandwidth Management. . 1-5
Dynamic SCPC (dSCPC) . . . . . . . . 1-5
Turbo Product Coding . . . . . . . . . . 1-6
Header Compression . . . . . . . . . . 1-6
Payload Compression . . . . . . . . . . 1-6
Quality of Service . . . . . . . . . . . . 1-6
Data Encryption . . . . . . . . . . . . . 1-6
New in this Release . . . . . . . . . . . . . 1-6
1.5.4 Release . . . . . . . . . . . . . . 1-7
New DPC (Dynamic Power Control)
Enhancements . . . . . . . . . . . . 1-7
STDMA Power Hunt . . . . . . . . . . 1-7
Hitless Switching. . . . . . . . . . . . 1-7
VMS Registration and Managing Address
1-7
UDP Port Base Address . . . . . . . . 1-7
Auto Home State Failsafe . . . . . . . 1-8
SOTM (Satellite On The Move) . . . . 1-8
Dynamic Routing . . . . . . . . . . . 1-8
Dynamic QoS Rules . . . . . . . . . . 1-8
Customer Support . . . . . . . . . . . . . . . 1-9
Contact Information . . . . . . . . . . . 1-9
Return Material Authorization . . . . . . 1-9
Reader Comments / Corrections . . . . 1-9
Quick Start Configuration
Introduction . . . . . . . . . . . . . . . . . . 2-1
Initial Configuration . . . . . . . . . . . . . . 2-2

Table of Contents

Terminal Connection . . . . . . . . . . 2-2
Network Role . . . . . . . . . . . . . . . . 2-3
Setting Vipersat CDM-570/570L Operating
Parameters. . . . . . . . . . . . . . . . . 2-3
Set the Feature Configuration . . . . . . 2-3
Set the IP Address . . . . . . . . . . . 2-6
Configure the Route Table . . . . . . . 2-7
Routing in a Vipersat Network. . . . . 2-7
Creating the Routes . . . . . . . . . . 2-8
Set the Satellite Modem Configuration 2-10
Set the Vipersat Configuration . . . . 2-10
Using the Command Line Interface
(CLI)
General . . . . . . . . . . . . . . . . . . . . . 3-1
Common Screen Commands . . . . . . . . 3-2
Save Parameters to Permanent Storage 3-2
Exit . . . . . . . . . . . . . . . . . . . 3-2
Telnet Logout . . . . . . . . . . . . . . 3-2
Menu Descriptions . . . . . . . . . . . . . . . 3-3
Main menu . . . . . . . . . . . . . . . . . 3-3
Administration . . . . . . . . . . . . . . 3-3
Feature Configuration . . . . . . . . . . . . 3-5
Vipersat Feature Codes . . . . . . . . . 3-5
Vipersat Management . . . . . . . . . . 3-6
Vipersat STDMA . . . . . . . . . . . . 3-6
Vipersat Auto Switching . . . . . . . . . 3-6
Vipersat File Streamer. . . . . . . . . . 3-7
Vipersat Configuration . . . . . . . . . . . . . 3-8
STDMA Mode . . . . . . . . . . . . . . . . 3-8
STDMA . . . . . . . . . . . . . . . . . 3-9
STDMA Tx Rate . . . . . . . . . . . . . 3-9
Hub Type . . . . . . . . . . . . . . . 3-10
1 - Fixed . . . . . . . . . . . . . . 3-10
2 - Dynamic Slot . . . . . . . . . . 3-11
3 - Dynamic Cycle . . . . . . . . . 3-11
4 - GIR . . . . . . . . . . . . . . . 3-11
5 - Entry Channel . . . . . . . . . . 3-12
Group ID. . . . . . . . . . . . . . . . 3-12
STDMA Power Hunt. . . . . . . . . . 3-13
Low Data Rate Fast Acquisition . . . . 3-13
Burstmap Multicast IP . . . . . . . . . 3-14
Outbound IP . . . . . . . . . . . . . . 3-14
Cycles Per Burst Map . . . . . . . . . 3-15
Slot Guardband . . . . . . . . . . . . 3-15
i