Porter-Cable 10 IN. (254 MM) JOBSITE TABLE SAW Instruction Manual page 17

6. Thread the arbor nut (2) onto the arbor, making sure
the flat side of the nut is against the blade, then
hand-tighten. (Fig. T)
7. To tighten the arbor nut (2), place the open-end
wrench (5) on the flats of the saw arbor to keep the
arbor from turning. (Fig. T)
8. Place the box-end wrench (6) on the arbor nut (2)
and turn clockwise (to the rear of the saw table).
(Fig. T)
9. Lower the blade to its minimum height position and
place insert (1) into position. (Fig. R)
Fig. T
WARNING
!
To avoid possible injury and damage to the
workpiece, be sure to INSTALL THE BLADE WITH
THE TEETH POINTING TOWARD THE FRONT OF
TABLE in the direction of the rotation arrow on the
blade guard.
REMOVING THE BLADE (FIG. R, T)
WARNING
!
To avoid injury from an accidental start, make sure
the switch is in the OFF position and the plug is
disconnected from the power source outlet.
1. Remove the table insert by snapping out from the
hole (8). (Fig. R)
2. Raise the blade to the maximum height by turning
the blade elevation handwheel clockwise.
3. Adjust the blade to the 90° vertical position by
unlocking the blade tilting lock handle and turning the
blade tilting handwheel counterclockwise, and then
lock into position.
4. Place the box end blade wrench (6) on the arbor nut
(2). (Fig. T)
5. To loosen the arbor nut (2), place the open-end
wrench (5) on the flats of the saw arbor to keep the
arbor from turning. (Fig. T)
6. Remove the blade (7). Clean but do not remove the
inner blade flange before reassembling the blade.
(Fig. T)
5
7
3
2
4
6
ADJUSTING THE 90° AND 45° POSITIVE STOPS
(FIG. U, V)
Your saw has positive stops that will quickly position the
saw blade at 90° and 45° to the table. Make adjustments
only if necessary.
90° Stop
1. Disconnect the saw from the power source.
2. Turn the blade elevation handwheel and raise the
blade to the maximum elevation.
3. Loosen the blade bevel lock handle and move the
blade (1) to the maximum vertical position, then
tighten the lock handle.
4. Place a combination square (2) on the table and
against the blade (1) to determine if the blade is 90°
to the table. (Fig. U)
5. If the blade is not 90° to the table, loosen the two set
screws (4), located on the collar (5) underneath the
table saw (Fig. V) with the hex key, and back off the
collar.
6. Loosen the bevel lock knob, turn the blade tilting
handwheel to move the blade until it is 90° to the
table and tighten the bevel lock knob.
7. Adjust the collar (5) so it contacts the bracket (3)
when the blade is 90° to the table. Tighten the two
set screws (4). (Fig. V)
Fig. U
°
90
45° Stop
1. With the blade in the upright 90° position, loosen the
bevel lock handle and move the blade to the
maximum bevel angle.
2. Place the combination square on the table as shown
in Fig. U to check if the blade is 45° to the table.
3. If the blade is not 45° to the table, loosen the two set
screws (4), located on the collar (5) the table saw,
with the hex key, and back off the collar underneath.
(Fig. V)
4. Loosen the bevel lock handle, turn the blade tilting
handwheel to move the blade until it is 45° to the table
and tighten the blade bevel lock handle.
17
°
45
2
1